Create printer.cfg
This commit is contained in:
chron-kh
parent
3780605aae
commit
bec1d849d1
GPG Key ID:
4AEE18F83AFDEB23
504
Mods/Chron/SKR 1.3 Config/printer.cfg
Normal file
504
Mods/Chron/SKR 1.3 Config/printer.cfg
Normal file
@ -0,0 +1,504 @@
|
|||||||
|
# CHRONS VORON2 300mm SKR 1.3 TMC2208 UART config
|
||||||
|
|
||||||
|
# *** THINGS TO CHANGE/CHECK: ***
|
||||||
|
# Arduino paths [mcu] section
|
||||||
|
# Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
||||||
|
# FSR switch (z endstop) location [homing_override] section
|
||||||
|
# FSR switch (z endstop) offset for Z0 [stepper_z] section
|
||||||
|
# Probe points [quad_gantry_level] section
|
||||||
|
# Min & Max gantry corner postions [quad_gantry_level] section
|
||||||
|
# PID tune [extruder] and [heater_bed] sections
|
||||||
|
# Fine tune E steps [extruder] section
|
||||||
|
|
||||||
|
# ========================== Pin Definitions ==========================
|
||||||
|
# X_STEP_PIN 2.2
|
||||||
|
# X_DIR_PIN 2.6
|
||||||
|
# X_ENABLE_PIN 2.1
|
||||||
|
# X_MIN_PIN 1.29
|
||||||
|
# X_MAX_PIN 1.28
|
||||||
|
# X_UART_RX 1.17
|
||||||
|
# X_UART_TX 4.29
|
||||||
|
|
||||||
|
# Y_STEP_PIN 0.19
|
||||||
|
# Y_DIR_PIN 0.20
|
||||||
|
# Y_ENABLE_PIN 2.8
|
||||||
|
# Y_MIN_PIN 1.27
|
||||||
|
# Y_MAX_PIN 1.26
|
||||||
|
# Y_UART_RX 1.15
|
||||||
|
# Y_UART_TX 1.16
|
||||||
|
|
||||||
|
# Z_STEP_PIN 0.22
|
||||||
|
# Z_DIR_PIN 2.11
|
||||||
|
# Z_ENABLE_PIN 0.21
|
||||||
|
# Z_MIN_PIN 1.25
|
||||||
|
# Z_MAX_PIN 1.24
|
||||||
|
# Z_UART_RX 1.10
|
||||||
|
# Z_UART_TX 1.14
|
||||||
|
|
||||||
|
# E0_STEP_PIN 2.13
|
||||||
|
# E0_DIR_PIN 0.11
|
||||||
|
# E0_ENABLE_PIN 2.12
|
||||||
|
# E0_UART_RX 1.8
|
||||||
|
# E0_UART_TX 1.9
|
||||||
|
|
||||||
|
# E1_STEP_PIN 0.1
|
||||||
|
# E1_DIR_PIN 0.0
|
||||||
|
# E1_ENABLE_PIN 0.10
|
||||||
|
# E1_UART_RX 1.1
|
||||||
|
# E1_UART_TX 1.4
|
||||||
|
|
||||||
|
# HE1 2.4
|
||||||
|
# HE0 2.7
|
||||||
|
# BED 2.5
|
||||||
|
# TH1 (H1 Temp) 0.25
|
||||||
|
# TH0 (H0 Temp) 0.24
|
||||||
|
# TB (Bed Temp) 0.23
|
||||||
|
# FAN 2.3
|
||||||
|
# SERVO 2.0
|
||||||
|
# =====================================================================
|
||||||
|
|
||||||
|
|
||||||
|
[force_move]
|
||||||
|
enable_force_move: True
|
||||||
|
|
||||||
|
[mcu]
|
||||||
|
# mcu for X/Y/E steppers main MCU
|
||||||
|
# [X in X] - B Motor
|
||||||
|
# [Y in Y] - A Motor
|
||||||
|
# [E in Z] - Extruder
|
||||||
|
# obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify
|
||||||
|
serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.2:1.0
|
||||||
|
|
||||||
|
[mcu z]
|
||||||
|
# mcu for Z steppers
|
||||||
|
# [Z in X] - Front Left
|
||||||
|
# [Z1 in Y] - Rear Left
|
||||||
|
# [Z2 in Z] - Rear Right
|
||||||
|
# [Z3 in E0]- Front Right
|
||||||
|
# obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify
|
||||||
|
serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.3:1.0
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: corexy
|
||||||
|
max_velocity: 350
|
||||||
|
max_accel: 4000
|
||||||
|
max_z_velocity: 50
|
||||||
|
max_z_accel: 350
|
||||||
|
# The maximum velocity (in mm/s) that the toolhead may travel a 90
|
||||||
|
# degree corner at. A non-zero value can reduce changes in extruder
|
||||||
|
# flow rates by enabling instantaneous velocity changes of the
|
||||||
|
# toolhead during cornering. This value configures the internal
|
||||||
|
# centripetal velocity cornering algorithm; corners with angles
|
||||||
|
# larger than 90 degrees will have a higher cornering velocity while
|
||||||
|
# corners with angles less than 90 degrees will have a lower
|
||||||
|
# cornering velocity. If this is set to zero then the toolhead will
|
||||||
|
# decelerate to zero at each corner. The default is 5mm/s.
|
||||||
|
#square_corner_velocity: 10.0
|
||||||
|
|
||||||
|
|
||||||
|
#
|
||||||
|
# TMC2208 UART Section for x/y
|
||||||
|
#
|
||||||
|
|
||||||
|
[stepper_x]
|
||||||
|
#connected to X on mcu_xye (B Motor)
|
||||||
|
step_pin: P2.2
|
||||||
|
dir_pin: !P2.6
|
||||||
|
enable_pin: !P2.1
|
||||||
|
step_distance: 0.0125
|
||||||
|
endstop_pin: P1.29
|
||||||
|
position_min: 0
|
||||||
|
position_endstop: 305
|
||||||
|
position_max: 305
|
||||||
|
homing_speed: 50
|
||||||
|
homing_retract_dist: 5
|
||||||
|
homing_positive_dir: true
|
||||||
|
|
||||||
|
[tmc2208 stepper_x]
|
||||||
|
uart_pin: P1.17
|
||||||
|
microsteps: 16
|
||||||
|
interpolate: True
|
||||||
|
run_current: 0.8
|
||||||
|
hold_current: 0.5
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 250
|
||||||
|
|
||||||
|
[stepper_y]
|
||||||
|
#connected to Y on mcu_xye (A Motor)
|
||||||
|
step_pin: P0.19
|
||||||
|
dir_pin: !P0.20
|
||||||
|
enable_pin: !P2.8
|
||||||
|
step_distance: 0.0125
|
||||||
|
endstop_pin: P1.27
|
||||||
|
position_min: 0
|
||||||
|
position_endstop: 305
|
||||||
|
position_max: 305
|
||||||
|
homing_speed: 50
|
||||||
|
homing_retract_dist: 5
|
||||||
|
homing_positive_dir: true
|
||||||
|
|
||||||
|
[tmc2208 stepper_y]
|
||||||
|
uart_pin: P1.15
|
||||||
|
microsteps: 16
|
||||||
|
interpolate: True
|
||||||
|
run_current: 0.8
|
||||||
|
hold_current: 0.5
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 250
|
||||||
|
|
||||||
|
#
|
||||||
|
# TMC2208 UART Section for z
|
||||||
|
#
|
||||||
|
|
||||||
|
#Z MCU - IN X
|
||||||
|
# Z0 Stepper - Front Left
|
||||||
|
[stepper_z]
|
||||||
|
step_pin: z:P2.2
|
||||||
|
dir_pin: !z:P2.6
|
||||||
|
enable_pin: !z:P2.1
|
||||||
|
step_distance: 0.00250
|
||||||
|
endstop_pin: !z:P1.25
|
||||||
|
# Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||||
|
# (+) value = endstop above Z0, (-) value = endstop below
|
||||||
|
position_endstop: -0.5
|
||||||
|
position_max: 240
|
||||||
|
position_min: -5
|
||||||
|
homing_speed: 15.0
|
||||||
|
second_homing_speed: 3.0
|
||||||
|
homing_retract_dist: 3.0
|
||||||
|
|
||||||
|
[tmc2208 stepper_z]
|
||||||
|
uart_pin: z:P1.17
|
||||||
|
microsteps: 16
|
||||||
|
interpolate: True
|
||||||
|
run_current: 0.90
|
||||||
|
hold_current: 0.80
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 50
|
||||||
|
|
||||||
|
#Z MCU - IN Y
|
||||||
|
# Z1 Stepper - Rear Left
|
||||||
|
[stepper_z1]
|
||||||
|
step_pin: z:P0.19
|
||||||
|
dir_pin: z:P0.20
|
||||||
|
enable_pin: !z:P2.8
|
||||||
|
step_distance: 0.00250
|
||||||
|
|
||||||
|
|
||||||
|
[tmc2208 stepper_z1]
|
||||||
|
uart_pin: z:P1.15
|
||||||
|
microsteps: 16
|
||||||
|
interpolate: True
|
||||||
|
run_current: 0.80
|
||||||
|
hold_current: 0.80
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 50
|
||||||
|
|
||||||
|
#Z MCU - IN Z
|
||||||
|
# Z2 Stepper - Rear Right
|
||||||
|
[stepper_z2]
|
||||||
|
step_pin: z:P0.22
|
||||||
|
dir_pin: !z:P2.11
|
||||||
|
enable_pin: !z:P0.21
|
||||||
|
step_distance: 0.00250
|
||||||
|
|
||||||
|
[tmc2208 stepper_z2]
|
||||||
|
uart_pin: z:P1.10
|
||||||
|
microsteps: 16
|
||||||
|
interpolate: True
|
||||||
|
run_current: 0.90
|
||||||
|
hold_current: 0.80
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 50
|
||||||
|
|
||||||
|
#Z MCU - IN E0
|
||||||
|
# Z3 Stepper - Front Right
|
||||||
|
[stepper_z3]
|
||||||
|
step_pin: z:P2.13
|
||||||
|
dir_pin: z:P0.11
|
||||||
|
enable_pin: !z:P2.12
|
||||||
|
step_distance: 0.00250
|
||||||
|
|
||||||
|
[tmc2208 stepper_z3]
|
||||||
|
uart_pin: z:P1.8
|
||||||
|
microsteps: 16
|
||||||
|
interpolate: True
|
||||||
|
run_current: 0.90
|
||||||
|
hold_current: 0.80
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 50
|
||||||
|
|
||||||
|
#
|
||||||
|
# bed heater, extruder and nozzle heater
|
||||||
|
#
|
||||||
|
|
||||||
|
#Z on MCU X/Y
|
||||||
|
[extruder]
|
||||||
|
step_pin: P2.13
|
||||||
|
dir_pin: P0.11
|
||||||
|
enable_pin: !P2.12
|
||||||
|
# 16 microsteps -m3 0.001875
|
||||||
|
step_distance: 0.00180180
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.75
|
||||||
|
heater_pin: P2.5
|
||||||
|
sensor_type: NTC 100K beta 3950
|
||||||
|
sensor_pin: P0.24
|
||||||
|
smooth_time: 3.0
|
||||||
|
min_temp: 10
|
||||||
|
max_temp: 270
|
||||||
|
max_power: 0.75
|
||||||
|
min_extrude_temp: 170
|
||||||
|
max_extrude_only_distance: 1150
|
||||||
|
max_extrude_cross_section: 9999
|
||||||
|
# PA can be disabled by declaring a 0.0 value
|
||||||
|
pressure_advance: 0.0
|
||||||
|
# time seconds to look ahead for PA moves default is 0.010 or 10ms
|
||||||
|
pressure_advance_lookahead_time: 0.010
|
||||||
|
control = pid
|
||||||
|
pid_kp = 26.213
|
||||||
|
pid_ki = 1.304
|
||||||
|
pid_kd = 131.721
|
||||||
|
|
||||||
|
#Z on MCU X/Y
|
||||||
|
[tmc2208 extruder]
|
||||||
|
uart_pin: P1.10
|
||||||
|
microsteps: 16
|
||||||
|
interpolate: True
|
||||||
|
run_current: 1.0
|
||||||
|
hold_current: 1.0
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 5
|
||||||
|
|
||||||
|
|
||||||
|
[probe]
|
||||||
|
# Inductive Probe
|
||||||
|
# Z height probe. One may define this section to enable Z height
|
||||||
|
# probing hardware. When this section is enabled, PROBE and
|
||||||
|
# QUERY_PROBE extended g-code commands become available. The probe
|
||||||
|
# section also creates a virtual "probe:z_virtual_endstop" pin. One
|
||||||
|
# may set the stepper_z endstop_pin to this virtual pin on cartesian
|
||||||
|
# style printers that use the probe in place of a z endstop.
|
||||||
|
pin: !z:P1.24
|
||||||
|
# Z_MAX on mcu_z
|
||||||
|
x_offset: 0
|
||||||
|
# Offset (in mm) for inductive probe Y direction from nozzle
|
||||||
|
y_offset: 25.0
|
||||||
|
z_offset: 0
|
||||||
|
# Speed (in mm/s) of the Z axis when probing. The default is 5mm/s.
|
||||||
|
speed: 2.0
|
||||||
|
samples: 4
|
||||||
|
# How far to retract (in mm) from the probe point for multi-probe samples
|
||||||
|
sample_retract_dist: 3.0
|
||||||
|
samples_tolerance: 0.100
|
||||||
|
# The maximum Z distance (in mm) that a sample may differ from other
|
||||||
|
# samples. If this tolerance is exceeded then either an error is
|
||||||
|
# reported or the attempt is restarted (see
|
||||||
|
# samples_tolerance_retries). The default is 0.100mm.
|
||||||
|
samples_tolerance_retries: 3
|
||||||
|
# The number of times to retry if a sample is found that exceeds
|
||||||
|
# samples_tolerance. On a retry, all current samples are discarded
|
||||||
|
# and the probe attempt is restarted. If a valid set of samples are
|
||||||
|
# not obtained in the given number of retries then an error is
|
||||||
|
# reported. The default is zero which causes an error to be reported
|
||||||
|
# on the first sample that exceeds samples_tolerance
|
||||||
|
|
||||||
|
|
||||||
|
#
|
||||||
|
# Fan control
|
||||||
|
#
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
# print cooling fans
|
||||||
|
pin: P2.4
|
||||||
|
#max_power: 0.5
|
||||||
|
kick_start_time: 0.5
|
||||||
|
cycle_time: 0.001
|
||||||
|
|
||||||
|
[heater_fan hotend_fan]
|
||||||
|
# Hotend fan MCU Z
|
||||||
|
pin: P2.7
|
||||||
|
#max_power: 0.8
|
||||||
|
#shutdown_speed: 0.0
|
||||||
|
kick_start_time: 0.5
|
||||||
|
heater: extruder
|
||||||
|
heater_temp: 50.0
|
||||||
|
#fan_speed: 1.0
|
||||||
|
|
||||||
|
#[heater_fan controller_fan]
|
||||||
|
# Controller fan
|
||||||
|
#pin: z:ar10
|
||||||
|
# D10 on mcu_z
|
||||||
|
#kick_start_time: 0.500
|
||||||
|
#heater: heater_bed
|
||||||
|
#heater_temp: 45.0
|
||||||
|
|
||||||
|
[heater_fan exhaust_fan]
|
||||||
|
pin: z:P2.4
|
||||||
|
#max_power: 1.0
|
||||||
|
#shutdown_speed: 0.0
|
||||||
|
kick_start_time: 5.0
|
||||||
|
heater: heater_bed
|
||||||
|
heater_temp: 60
|
||||||
|
#fan_speed: 1.0
|
||||||
|
|
||||||
|
[heater_bed]
|
||||||
|
heater_pin: z:P2.5
|
||||||
|
sensor_type: NTC 100K MGB18-104F39050L32
|
||||||
|
#pullup_resistor: 5500
|
||||||
|
sensor_pin: z:P0.25
|
||||||
|
smooth_time: 3.0
|
||||||
|
max_power: 1.0
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 110
|
||||||
|
control: pid
|
||||||
|
pid_kp: 58.437
|
||||||
|
pid_ki: 2.347
|
||||||
|
pid_kd: 363.769
|
||||||
|
|
||||||
|
[idle_timeout]
|
||||||
|
timeout: 1800
|
||||||
|
|
||||||
|
[verify_heater heater_bed]
|
||||||
|
hysteresis: 0.5
|
||||||
|
check_gain_time: 120
|
||||||
|
|
||||||
|
[homing_override]
|
||||||
|
axes: z
|
||||||
|
set_position_z: 0
|
||||||
|
gcode:
|
||||||
|
G90
|
||||||
|
G0 Z5 F600
|
||||||
|
G28 X Y
|
||||||
|
# XY Location of the FSR Switch
|
||||||
|
G0 X99.7 Y305 F3600
|
||||||
|
G28 Z
|
||||||
|
G0 Z10 F1800
|
||||||
|
G0 X150 Y150 Z30 F3600
|
||||||
|
|
||||||
|
|
||||||
|
[quad_gantry_level]
|
||||||
|
# Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||||
|
# Min & Max gantry corners - measure from nozzle at MIN (0,0) and MAX (300,300) to respective belt positions
|
||||||
|
gantry_corners:
|
||||||
|
-55,-7
|
||||||
|
355,370
|
||||||
|
# Probe points
|
||||||
|
points:
|
||||||
|
60,60
|
||||||
|
60,240
|
||||||
|
240,240
|
||||||
|
240,60
|
||||||
|
# The speed (in mm/s) of non-probing moves during the calibration.
|
||||||
|
# The default is 50.
|
||||||
|
speed: 50
|
||||||
|
# The height (in mm) that the head should be commanded to move to
|
||||||
|
# just prior to starting a probe operation. The default is 5
|
||||||
|
horizontal_move_z: 10
|
||||||
|
# number of times to retry if the stepper movements aren't within tolerance
|
||||||
|
retries: 5
|
||||||
|
# if retries are enabled then retry if any z_stepper movement was greater
|
||||||
|
# than the retry_tolerance
|
||||||
|
retry_tolerance: 0.0075
|
||||||
|
# Saftey limit if an ajustment greater than this value is requested
|
||||||
|
# quad_gantry_level will abort.
|
||||||
|
max_adjust: 10
|
||||||
|
|
||||||
|
|
||||||
|
# BED_MESH_CALIBRATE
|
||||||
|
[bed_mesh]
|
||||||
|
speed: 200
|
||||||
|
horizontal_move_z: 10
|
||||||
|
min_point: 20,20
|
||||||
|
max_point: 280,280
|
||||||
|
probe_count: 10,10
|
||||||
|
fade_start: 0.5
|
||||||
|
fade_end: 25.0
|
||||||
|
split_delta_z: .025
|
||||||
|
move_check_distance: 5.0
|
||||||
|
mesh_pps: 0,0
|
||||||
|
algorithm: bicubic
|
||||||
|
|
||||||
|
|
||||||
|
[display]
|
||||||
|
# RepRapDiscount 128x64 Full Graphic Smart Controller
|
||||||
|
lcd_type: st7920
|
||||||
|
cs_pin: z:P1.19
|
||||||
|
sclk_pin: z:P1.20
|
||||||
|
sid_pin: z:P1.18
|
||||||
|
# LCD connector on mcu_z
|
||||||
|
menu_timeout: 40
|
||||||
|
# Timeout for menu. Being inactive this amount of seconds will exit the menu
|
||||||
|
# Default is 0 seconds (disabled)
|
||||||
|
encoder_pins: ^z:P3.26, ^z:P3.25
|
||||||
|
click_pin: ^!z:P0.28
|
||||||
|
#kill_pin: ^!z:
|
||||||
|
|
||||||
|
|
||||||
|
### Macros ###
|
||||||
|
|
||||||
|
[gcode_macro G32]
|
||||||
|
gcode:
|
||||||
|
G28
|
||||||
|
QUAD_GANTRY_LEVEL
|
||||||
|
G28
|
||||||
|
G0 X150 Y150 Z20 F6000
|
||||||
|
|
||||||
|
[gcode_macro PRINT_START]
|
||||||
|
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
||||||
|
gcode:
|
||||||
|
M117 Homing... ; display message
|
||||||
|
G28 ; home all axes
|
||||||
|
G1 Z20 F3000 ; move nozzle away from bed
|
||||||
|
M117 Preheat (Print) ; display message
|
||||||
|
M104 S0 ; turn off hotend while waiting for bed to get to temp)
|
||||||
|
|
||||||
|
[gcode_macro PRINT_END]
|
||||||
|
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
||||||
|
gcode:
|
||||||
|
M400 ; wait for buffer to clear
|
||||||
|
G92 E0 ; zero the extruder
|
||||||
|
G1 E-10.0 F3600 ; retract filament
|
||||||
|
G91 ; relative positioning
|
||||||
|
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
||||||
|
TURN_OFF_HEATERS
|
||||||
|
M107 ; turn off fan
|
||||||
|
G1 Z2 F3000 ; move nozzle up 2mm
|
||||||
|
G90 ; absolute positioning
|
||||||
|
G0 X125 Y250 F3600 ; park nozzle at rear
|
||||||
|
M117 Finished!
|
||||||
|
|
||||||
|
[gcode_macro LOAD_FILAMENT]
|
||||||
|
gcode:
|
||||||
|
M83 ; set extruder to relative
|
||||||
|
G1 E750 F1800 ; quickly load filament to down bowden
|
||||||
|
G1 E30 F300 ; slower extrusion for hotend path
|
||||||
|
G1 E15 F150 ; prime nozzle with filament
|
||||||
|
M82 ; set extruder to absolute
|
||||||
|
|
||||||
|
[gcode_macro UNLOAD_FILAMENT]
|
||||||
|
gcode:
|
||||||
|
M83 ; set extruder to relative
|
||||||
|
G1 E10 F300 ; extrude a little to soften tip
|
||||||
|
G1 E-780 F1800 ; retract filament completely
|
||||||
|
M82 ; set extruder to absolute
|
||||||
|
|
||||||
|
[gcode_macro quad_me]
|
||||||
|
gcode:
|
||||||
|
G28
|
||||||
|
quad_gantry_level
|
||||||
|
G28
|
||||||
|
quad_gantry_level
|
||||||
|
G28
|
||||||
|
quad_gantry_level
|
||||||
|
G28
|
||||||
|
G1 X150 Y150 Z20
|
||||||
|
|
||||||
|
# Sensor Types
|
||||||
|
# "EPCOS 100K B57560G104F"
|
||||||
|
# "ATC Semitec 104GT-2"
|
||||||
|
# "NTC 100K beta 3950"
|
||||||
|
# "Honeywell 100K 135-104LAG-J01"
|
||||||
|
# "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
|
||||||
|
# "AD595"
|
||||||
|
# "PT100 INA826"
|
||||||
Loading…
Reference in New Issue
Block a user