From bec1d849d1c8ae58a5bfa441193ee7ab7d3292e3 Mon Sep 17 00:00:00 2001 From: chron-kh <51377081+chron-kh@users.noreply.github.com> Date: Fri, 26 Jul 2019 13:49:28 -0400 Subject: [PATCH] Create printer.cfg --- Mods/Chron/SKR 1.3 Config/printer.cfg | 504 ++++++++++++++++++++++++++ 1 file changed, 504 insertions(+) create mode 100644 Mods/Chron/SKR 1.3 Config/printer.cfg diff --git a/Mods/Chron/SKR 1.3 Config/printer.cfg b/Mods/Chron/SKR 1.3 Config/printer.cfg new file mode 100644 index 0000000..f82aab3 --- /dev/null +++ b/Mods/Chron/SKR 1.3 Config/printer.cfg @@ -0,0 +1,504 @@ +# CHRONS VORON2 300mm SKR 1.3 TMC2208 UART config + +# *** THINGS TO CHANGE/CHECK: *** +# Arduino paths [mcu] section +# Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file +# FSR switch (z endstop) location [homing_override] section +# FSR switch (z endstop) offset for Z0 [stepper_z] section +# Probe points [quad_gantry_level] section +# Min & Max gantry corner postions [quad_gantry_level] section +# PID tune [extruder] and [heater_bed] sections +# Fine tune E steps [extruder] section + +# ========================== Pin Definitions ========================== +# X_STEP_PIN 2.2 +# X_DIR_PIN 2.6 +# X_ENABLE_PIN 2.1 +# X_MIN_PIN 1.29 +# X_MAX_PIN 1.28 +# X_UART_RX 1.17 +# X_UART_TX 4.29 + +# Y_STEP_PIN 0.19 +# Y_DIR_PIN 0.20 +# Y_ENABLE_PIN 2.8 +# Y_MIN_PIN 1.27 +# Y_MAX_PIN 1.26 +# Y_UART_RX 1.15 +# Y_UART_TX 1.16 + +# Z_STEP_PIN 0.22 +# Z_DIR_PIN 2.11 +# Z_ENABLE_PIN 0.21 +# Z_MIN_PIN 1.25 +# Z_MAX_PIN 1.24 +# Z_UART_RX 1.10 +# Z_UART_TX 1.14 + +# E0_STEP_PIN 2.13 +# E0_DIR_PIN 0.11 +# E0_ENABLE_PIN 2.12 +# E0_UART_RX 1.8 +# E0_UART_TX 1.9 + +# E1_STEP_PIN 0.1 +# E1_DIR_PIN 0.0 +# E1_ENABLE_PIN 0.10 +# E1_UART_RX 1.1 +# E1_UART_TX 1.4 + +# HE1 2.4 +# HE0 2.7 +# BED 2.5 +# TH1 (H1 Temp) 0.25 +# TH0 (H0 Temp) 0.24 +# TB (Bed Temp) 0.23 +# FAN 2.3 +# SERVO 2.0 +# ===================================================================== + + +[force_move] +enable_force_move: True + +[mcu] +# mcu for X/Y/E steppers main MCU +# [X in X] - B Motor +# [Y in Y] - A Motor +# [E in Z] - Extruder +# obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify +serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.2:1.0 + +[mcu z] +# mcu for Z steppers +# [Z in X] - Front Left +# [Z1 in Y] - Rear Left +# [Z2 in Z] - Rear Right +# [Z3 in E0]- Front Right +# obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify +serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.3:1.0 + +[printer] +kinematics: corexy +max_velocity: 350 +max_accel: 4000 +max_z_velocity: 50 +max_z_accel: 350 +# The maximum velocity (in mm/s) that the toolhead may travel a 90 +# degree corner at. A non-zero value can reduce changes in extruder +# flow rates by enabling instantaneous velocity changes of the +# toolhead during cornering. This value configures the internal +# centripetal velocity cornering algorithm; corners with angles +# larger than 90 degrees will have a higher cornering velocity while +# corners with angles less than 90 degrees will have a lower +# cornering velocity. If this is set to zero then the toolhead will +# decelerate to zero at each corner. The default is 5mm/s. +#square_corner_velocity: 10.0 + + +# +# TMC2208 UART Section for x/y +# + +[stepper_x] +#connected to X on mcu_xye (B Motor) +step_pin: P2.2 +dir_pin: !P2.6 +enable_pin: !P2.1 +step_distance: 0.0125 +endstop_pin: P1.29 +position_min: 0 +position_endstop: 305 +position_max: 305 +homing_speed: 50 +homing_retract_dist: 5 +homing_positive_dir: true + +[tmc2208 stepper_x] +uart_pin: P1.17 +microsteps: 16 +interpolate: True +run_current: 0.8 +hold_current: 0.5 +sense_resistor: 0.110 +stealthchop_threshold: 250 + +[stepper_y] +#connected to Y on mcu_xye (A Motor) +step_pin: P0.19 +dir_pin: !P0.20 +enable_pin: !P2.8 +step_distance: 0.0125 +endstop_pin: P1.27 +position_min: 0 +position_endstop: 305 +position_max: 305 +homing_speed: 50 +homing_retract_dist: 5 +homing_positive_dir: true + +[tmc2208 stepper_y] +uart_pin: P1.15 +microsteps: 16 +interpolate: True +run_current: 0.8 +hold_current: 0.5 +sense_resistor: 0.110 +stealthchop_threshold: 250 + +# +# TMC2208 UART Section for z +# + +#Z MCU - IN X +# Z0 Stepper - Front Left +[stepper_z] +step_pin: z:P2.2 +dir_pin: !z:P2.6 +enable_pin: !z:P2.1 +step_distance: 0.00250 +endstop_pin: !z:P1.25 +# Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) +# (+) value = endstop above Z0, (-) value = endstop below +position_endstop: -0.5 +position_max: 240 +position_min: -5 +homing_speed: 15.0 +second_homing_speed: 3.0 +homing_retract_dist: 3.0 + +[tmc2208 stepper_z] +uart_pin: z:P1.17 +microsteps: 16 +interpolate: True +run_current: 0.90 +hold_current: 0.80 +sense_resistor: 0.110 +stealthchop_threshold: 50 + +#Z MCU - IN Y +# Z1 Stepper - Rear Left +[stepper_z1] +step_pin: z:P0.19 +dir_pin: z:P0.20 +enable_pin: !z:P2.8 +step_distance: 0.00250 + + +[tmc2208 stepper_z1] +uart_pin: z:P1.15 +microsteps: 16 +interpolate: True +run_current: 0.80 +hold_current: 0.80 +sense_resistor: 0.110 +stealthchop_threshold: 50 + +#Z MCU - IN Z +# Z2 Stepper - Rear Right +[stepper_z2] +step_pin: z:P0.22 +dir_pin: !z:P2.11 +enable_pin: !z:P0.21 +step_distance: 0.00250 + +[tmc2208 stepper_z2] +uart_pin: z:P1.10 +microsteps: 16 +interpolate: True +run_current: 0.90 +hold_current: 0.80 +sense_resistor: 0.110 +stealthchop_threshold: 50 + +#Z MCU - IN E0 +# Z3 Stepper - Front Right +[stepper_z3] +step_pin: z:P2.13 +dir_pin: z:P0.11 +enable_pin: !z:P2.12 +step_distance: 0.00250 + +[tmc2208 stepper_z3] +uart_pin: z:P1.8 +microsteps: 16 +interpolate: True +run_current: 0.90 +hold_current: 0.80 +sense_resistor: 0.110 +stealthchop_threshold: 50 + +# +# bed heater, extruder and nozzle heater +# + +#Z on MCU X/Y +[extruder] +step_pin: P2.13 +dir_pin: P0.11 +enable_pin: !P2.12 +# 16 microsteps -m3 0.001875 +step_distance: 0.00180180 +nozzle_diameter: 0.400 +filament_diameter: 1.75 +heater_pin: P2.5 +sensor_type: NTC 100K beta 3950 +sensor_pin: P0.24 +smooth_time: 3.0 +min_temp: 10 +max_temp: 270 +max_power: 0.75 +min_extrude_temp: 170 +max_extrude_only_distance: 1150 +max_extrude_cross_section: 9999 +# PA can be disabled by declaring a 0.0 value +pressure_advance: 0.0 +# time seconds to look ahead for PA moves default is 0.010 or 10ms +pressure_advance_lookahead_time: 0.010 +control = pid +pid_kp = 26.213 +pid_ki = 1.304 +pid_kd = 131.721 + +#Z on MCU X/Y +[tmc2208 extruder] +uart_pin: P1.10 +microsteps: 16 +interpolate: True +run_current: 1.0 +hold_current: 1.0 +sense_resistor: 0.110 +stealthchop_threshold: 5 + + +[probe] +# Inductive Probe +# Z height probe. One may define this section to enable Z height +# probing hardware. When this section is enabled, PROBE and +# QUERY_PROBE extended g-code commands become available. The probe +# section also creates a virtual "probe:z_virtual_endstop" pin. One +# may set the stepper_z endstop_pin to this virtual pin on cartesian +# style printers that use the probe in place of a z endstop. +pin: !z:P1.24 +# Z_MAX on mcu_z +x_offset: 0 +# Offset (in mm) for inductive probe Y direction from nozzle +y_offset: 25.0 +z_offset: 0 +# Speed (in mm/s) of the Z axis when probing. The default is 5mm/s. +speed: 2.0 +samples: 4 +# How far to retract (in mm) from the probe point for multi-probe samples +sample_retract_dist: 3.0 +samples_tolerance: 0.100 +# The maximum Z distance (in mm) that a sample may differ from other +# samples. If this tolerance is exceeded then either an error is +# reported or the attempt is restarted (see +# samples_tolerance_retries). The default is 0.100mm. +samples_tolerance_retries: 3 +# The number of times to retry if a sample is found that exceeds +# samples_tolerance. On a retry, all current samples are discarded +# and the probe attempt is restarted. If a valid set of samples are +# not obtained in the given number of retries then an error is +# reported. The default is zero which causes an error to be reported +# on the first sample that exceeds samples_tolerance + + +# +# Fan control +# + +[fan] +# print cooling fans +pin: P2.4 +#max_power: 0.5 +kick_start_time: 0.5 +cycle_time: 0.001 + +[heater_fan hotend_fan] +# Hotend fan MCU Z +pin: P2.7 +#max_power: 0.8 +#shutdown_speed: 0.0 +kick_start_time: 0.5 +heater: extruder +heater_temp: 50.0 +#fan_speed: 1.0 + +#[heater_fan controller_fan] +# Controller fan +#pin: z:ar10 +# D10 on mcu_z +#kick_start_time: 0.500 +#heater: heater_bed +#heater_temp: 45.0 + +[heater_fan exhaust_fan] +pin: z:P2.4 +#max_power: 1.0 +#shutdown_speed: 0.0 +kick_start_time: 5.0 +heater: heater_bed +heater_temp: 60 +#fan_speed: 1.0 + +[heater_bed] +heater_pin: z:P2.5 +sensor_type: NTC 100K MGB18-104F39050L32 +#pullup_resistor: 5500 +sensor_pin: z:P0.25 +smooth_time: 3.0 +max_power: 1.0 +min_temp: 0 +max_temp: 110 +control: pid +pid_kp: 58.437 +pid_ki: 2.347 +pid_kd: 363.769 + +[idle_timeout] +timeout: 1800 + +[verify_heater heater_bed] +hysteresis: 0.5 +check_gain_time: 120 + +[homing_override] +axes: z +set_position_z: 0 +gcode: + G90 + G0 Z5 F600 + G28 X Y + # XY Location of the FSR Switch + G0 X99.7 Y305 F3600 + G28 Z + G0 Z10 F1800 + G0 X150 Y150 Z30 F3600 + + +[quad_gantry_level] +# Use QUAD_GANTRY_LEVEL to level a gantry. +# Min & Max gantry corners - measure from nozzle at MIN (0,0) and MAX (300,300) to respective belt positions +gantry_corners: + -55,-7 + 355,370 +# Probe points +points: + 60,60 + 60,240 + 240,240 + 240,60 + # The speed (in mm/s) of non-probing moves during the calibration. +# The default is 50. +speed: 50 +# The height (in mm) that the head should be commanded to move to +# just prior to starting a probe operation. The default is 5 +horizontal_move_z: 10 +# number of times to retry if the stepper movements aren't within tolerance +retries: 5 +# if retries are enabled then retry if any z_stepper movement was greater +# than the retry_tolerance +retry_tolerance: 0.0075 +# Saftey limit if an ajustment greater than this value is requested +# quad_gantry_level will abort. +max_adjust: 10 + + +# BED_MESH_CALIBRATE +[bed_mesh] +speed: 200 +horizontal_move_z: 10 +min_point: 20,20 +max_point: 280,280 +probe_count: 10,10 +fade_start: 0.5 +fade_end: 25.0 +split_delta_z: .025 +move_check_distance: 5.0 +mesh_pps: 0,0 +algorithm: bicubic + + +[display] +# RepRapDiscount 128x64 Full Graphic Smart Controller +lcd_type: st7920 +cs_pin: z:P1.19 +sclk_pin: z:P1.20 +sid_pin: z:P1.18 +# LCD connector on mcu_z +menu_timeout: 40 +# Timeout for menu. Being inactive this amount of seconds will exit the menu +# Default is 0 seconds (disabled) +encoder_pins: ^z:P3.26, ^z:P3.25 +click_pin: ^!z:P0.28 +#kill_pin: ^!z: + + +### Macros ### + +[gcode_macro G32] +gcode: + G28 + QUAD_GANTRY_LEVEL + G28 + G0 X150 Y150 Z20 F6000 + +[gcode_macro PRINT_START] +# Use PRINT_START for the slicer starting script - please customise for your slicer of choice +gcode: + M117 Homing... ; display message + G28 ; home all axes + G1 Z20 F3000 ; move nozzle away from bed + M117 Preheat (Print) ; display message + M104 S0 ; turn off hotend while waiting for bed to get to temp) + +[gcode_macro PRINT_END] +# Use PRINT_END for the slicer ending script - please customise for your slicer of choice +gcode: + M400 ; wait for buffer to clear + G92 E0 ; zero the extruder + G1 E-10.0 F3600 ; retract filament + G91 ; relative positioning + G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing + TURN_OFF_HEATERS + M107 ; turn off fan + G1 Z2 F3000 ; move nozzle up 2mm + G90 ; absolute positioning + G0 X125 Y250 F3600 ; park nozzle at rear + M117 Finished! + +[gcode_macro LOAD_FILAMENT] +gcode: + M83 ; set extruder to relative + G1 E750 F1800 ; quickly load filament to down bowden + G1 E30 F300 ; slower extrusion for hotend path + G1 E15 F150 ; prime nozzle with filament + M82 ; set extruder to absolute + +[gcode_macro UNLOAD_FILAMENT] +gcode: + M83 ; set extruder to relative + G1 E10 F300 ; extrude a little to soften tip + G1 E-780 F1800 ; retract filament completely + M82 ; set extruder to absolute + +[gcode_macro quad_me] +gcode: + G28 + quad_gantry_level + G28 + quad_gantry_level + G28 + quad_gantry_level + G28 + G1 X150 Y150 Z20 + +# Sensor Types +# "EPCOS 100K B57560G104F" +# "ATC Semitec 104GT-2" +# "NTC 100K beta 3950" +# "Honeywell 100K 135-104LAG-J01" +# "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad) +# "AD595" +# "PT100 INA826"