1
0
mirror of https://git.openwrt.org/openwrt/openwrt.git synced 2024-10-20 06:28:12 +02:00
openwrt/target/linux
Piotr Dymacz 6492ea7d9e ath79: add support for ALFA Network N2Q
ALFA Network N2Q is an outdoor N300 AP/CPE based on Qualcomm/Atheros
QCA9531 v2. This model is a successor of the old N2 which was based
on Atheros AR7240. FCC ID: 2AB8795311.

Specifications:

- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2T2R 2.4 GHz Wi-Fi with ext. PA (Skyworks SE2623L) and LNA
- 2x 10/100 Mbps Ethernet with passive PoE input in one port (24 V)
- PoE pass through in second port (controlled by GPIO)
- support for optional 802.3af/at PoE module
- 1x mini PCIe slot (PCIe bus, extra 4.2 V for high power cards)
- 2x IPEX/U.FL connectors on PCB
- 1x USB 2.0 mini Type-B (power controlled by GPIO)
- 8x LED (7 of them are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- UART (4-pin, 2.54 mm pitch) header on PCB
- LEDs (2x 5-pin, 2.54 mm pitch) header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-09-28 01:28:37 +02:00
..
apm821xx treewide: remove empty default cases 2020-09-17 12:46:19 +02:00
arc770 arc770: drop support for kernel 4.14 2020-09-02 16:29:22 +02:00
archs38
armvirt
at91 at91: explicitly set CONFIG_USB_SUPPORT for sam9x subtarget 2020-08-27 16:36:18 +02:00
ath25 ath25: fix preinit Ethernet port configuration 2020-09-10 18:52:15 +02:00
ath79 ath79: add support for ALFA Network N2Q 2020-09-28 01:28:37 +02:00
bcm27xx kernel: bump 5.4 to 5.4.67 2020-09-24 18:53:23 +02:00
bcm47xx kernel: bump 5.4 to 5.4.64 2020-09-12 01:28:50 +02:00
bcm53xx bcm53xx: add Cisco Meraki MR32 2020-09-25 19:32:34 +02:00
bcm63xx kernel: bump 5.4 to 5.4.67 2020-09-24 18:53:23 +02:00
gemini gemini: Bring up DSA switches 2020-09-25 19:32:34 +02:00
generic kernel: add default for new config symbols 2020-09-25 19:32:34 +02:00
imx6
ipq40xx ipq40xx: tidy up device recipe for Edgecore OAP100 2020-09-26 18:26:19 +02:00
ipq806x ipq806x: fix support of Edgecore ECW5410 support 2020-09-19 13:32:11 +02:00
ipq807x
kirkwood target: update SPDX license names 2020-09-22 20:58:26 +02:00
lantiq kernel: bump 5.4 to 5.4.67 2020-09-24 18:53:23 +02:00
layerscape kernel: bump 5.4 to 5.4.67 2020-09-24 18:53:23 +02:00
malta
mediatek kernel: bump 5.4 to 5.4.67 2020-09-24 18:53:23 +02:00
mpc85xx target: update SPDX license names 2020-09-22 20:58:26 +02:00
mvebu target: update SPDX license names 2020-09-22 20:58:26 +02:00
mxs
octeon
octeontx
omap
oxnas target: update SPDX license names 2020-09-22 20:58:26 +02:00
pistachio pistachio: drop support for kernel 4.14 2020-09-02 16:29:22 +02:00
ramips ramips: merge ethernet setup for RT-AC51U/RT-AC54U 2020-09-28 00:20:24 +02:00
rockchip
rtl838x target: update SPDX license names 2020-09-22 20:58:26 +02:00
sunxi
tegra
uml
x86 kernel: bump 5.4 to 5.4.63 2020-09-06 19:55:19 +02:00
zynq
Makefile