1
0
mirror of https://git.openwrt.org/openwrt/openwrt.git synced 2024-10-20 14:38:20 +02:00
Commit Graph

23340 Commits

Author SHA1 Message Date
Piotr Dymacz
6492ea7d9e ath79: add support for ALFA Network N2Q
ALFA Network N2Q is an outdoor N300 AP/CPE based on Qualcomm/Atheros
QCA9531 v2. This model is a successor of the old N2 which was based
on Atheros AR7240. FCC ID: 2AB8795311.

Specifications:

- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2T2R 2.4 GHz Wi-Fi with ext. PA (Skyworks SE2623L) and LNA
- 2x 10/100 Mbps Ethernet with passive PoE input in one port (24 V)
- PoE pass through in second port (controlled by GPIO)
- support for optional 802.3af/at PoE module
- 1x mini PCIe slot (PCIe bus, extra 4.2 V for high power cards)
- 2x IPEX/U.FL connectors on PCB
- 1x USB 2.0 mini Type-B (power controlled by GPIO)
- 8x LED (7 of them are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- UART (4-pin, 2.54 mm pitch) header on PCB
- LEDs (2x 5-pin, 2.54 mm pitch) header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-09-28 01:28:37 +02:00
Piotr Dymacz
9bcf98ed85 ath79: add support for ALFA Network R36A
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2, FCC
ID: 2AB879531.

Support for this device was first introduced in af8f0629df (ar71xx
target). When updating from previous release (and/or ar71xx target),
user should only adjust the WAN LED trigger type (netdev in ar71xx,
switch port in ath79).

Specifications:

- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB (R36AH/-U2) or 64 MB (R36A) of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet
- Passive PoE input support (12~36 V) in RJ45 near DC jack
- 2T2R 2.4 GHz Wi-Fi with Qorvo RFFM8228P FEM
- 2x IPEX/U.FL connectors on PCB
- 1x USB 2.0 Type-A
- 1x USB 2.0 mini Type-B in R36AH-U2 version
- USB power is controlled by GPIO
- 6/7x LED (5/6 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- DC jack with lock, for main power input (12 V)
- UART (4-pin, 2.54 mm pitch) header on PCB

Optional/additional features in R36A series (R36A was the first model):
- for R36AH:    USB 2.0 hub*
- for R36AH-U2: USB 2.0 hub*, 1x USB 2.0 mini Type-B, one more LED

*) there are at least three different USB 2.0 hub in R36AH/-U2 variants:
- Terminus-Tech FE 1.1
- Genesys Logic GL852G
- Genesys Logic GL850G (used in latests revision)

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-09-28 01:28:37 +02:00
Piotr Dymacz
cf42660dce ath79: add support for Samsung WAM250
Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless
hub, dedicated for Samsung Shape Wireless Audio System. The device is
based on Atheros AR9344 (FCC ID: A3LWAM250). Support for this device
was first introduced in e58e49bdbe (ar71xx target).

Specifications:

- Atheros AR9344
- 560/450/225 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet
- 2T2R 2.4/5 GHz Wi-Fi, with ext. PA (SE2598L, SE5003L) and LNA
- 1x USB 2.0
- 4x LED (all are driven by GPIO)
- 2x button (reset, wps/speaker add)
- DC jack for main power input (14 V)
- UART header on PCB (J4, RX: 3, TX: 5)

Flash instruction:

This device uses dual-image (switched between upgrades) with a common
jffs2 config partition. Fortunately, there is a way to disable this mode
so that more flash space can be used by OpenWrt image.

You can easily access this device over telnet, using root/root
credentials (the same also work for serial console access).

1. Make sure that your device uses second (bootpart=2) image using
   command: "fw_printenv bootpart".
2. If your device uses first image (bootpart=1), perform upgrade to the
   latest vendor firmware (after the update, device should boot from
   second partition) using web gui (default login: admin/1234567890).
3. Rename "sysupgrade" image to "firmware.bin", download it (you can use
   wget, tftp or ftpget) to "/tmp" and issue below commands:

   mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}')
   mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin)
   fw_setenv bootpart
   fw_setenv bootcmd "bootm 0x9f070000"
   reboot

Revert to vendor firmware instruction:

1. Download vendor firmware to "/tmp" device and issue below commands:

   fw_setenv bootpart 1
   sysupgrade -n -F SS_BHUB_v2.2.05.bin

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-09-28 01:28:37 +02:00
Piotr Dymacz
f777bca95d ath79: image: don't combine kmod-usb2 with kmod-usb-chipidea2
Include of kmod-usb-chipidea2 is enough to support USB host mode in
devices with Atheros AR9331 WiSOC.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-09-28 01:28:37 +02:00
Piotr Dymacz
c65c306d33 ath79: add support for Wallys DR531
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2. Support for this
device was first introduced in e767980eb8 (ar71xx target).

Specifications:

- Qualcomm/Atheros QCA9531 v2
- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of flash (SPI NOR)
- 2T2R 2.4 GHz Wi-Fi, with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors (optional IPEX/U.FL)
- mini PCIe connector (PCIe/USB buses and mini SIM slot)
- 7x LED, 1x button, 1x optional buzzer
- UART, JTAG and LED headers on PCB

Flash instruction (do it under U-Boot, using UART):

  tftpb 0x80060000 openwrt-ath79-...-dr531-squashfs-sysupgrade.bin
  erase 0x9f050000 +$filesize
  cp.b $fileaddr 0x9f050000 $filesize
  setenv bootcmd "bootm 0x9f050000"
  saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-09-28 01:28:37 +02:00
Piotr Dymacz
66abd58196 ath79: add support for ALFA Network AP121FE
The AP121FE is a slightly modified version of already supported AP121F
model (added to ar71xx in 0c6165d21a and to ath79 in 334bbc5198).

The differences in compare to AP121F:

- no micro SD card reader
- USB data lines are included in Type-A plug
- USB bus switched to device/peripheral mode (permanently, in bootstrap)

Other than that, specifications are the same:

- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz Wi-Fi, up to 15 dBm
- 1x IPEX/U.FL connector, internal PCB antenna
- 3x LED, 1x button, 1x switch
- 4-pin UART header on PCB (2 mm pitch)
- USB 2.0 Type-A plug (power and data)

Flash instruction (under U-Boot web recovery mode):

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
   wait for first blink of all LEDs (indicates network setup), then keep
   button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-09-28 01:28:37 +02:00
Piotr Dymacz
7f96cbd2a1 ath79: enable usbgadget feature
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-09-28 01:28:37 +02:00
Piotr Dymacz
b329bb9456 ath79: increase SPI clock and enable fast-read on AP121F
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-09-28 01:28:37 +02:00
Adrian Schmutzler
315904a459 ramips: merge ethernet setup for RT-AC51U/RT-AC54U
The ethernet setup/label MAC address for RT-AC51U and RT-AC54U are
the same, so move them into the shared DTSI.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-28 00:20:24 +02:00
Adrian Schmutzler
96023cd4ba ath79: fix LED labels for PowerCloud CAP324
The order of function and color in the labels in inverted for the
LAN LEDs. Fix it.

Fixes: 915966d86121 ("ath79: Port PowerCloud Systems CAP324 support")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-27 15:58:14 +02:00
Adrian Schmutzler
d232a8ac7d ath79: fix rssi-low LED for My Net Range Extender
The LED color was missing in 01_leds.

Fixes: 745dee11ac78 ("ath79: add support for WD My Net Wi-Fi Range
Extender")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-27 15:58:14 +02:00
Sungbo Eo
4682d4d770 ipq40xx: tidy up device recipe for Edgecore OAP100
* split up DEVICE_TITLE into DEVICE_{VENDOR,MODEL}
* use SOC instead of DEVICE_DTS

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-09-26 18:26:19 +02:00
Adrian Schmutzler
621297e867 ramips: move dts-v1 statement to top-level DTSI files
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.

In ramips, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent mtxxxx/rtxxxx DTSI files already determines the DTS
version, so putting it into the DTS files is just a useless repetition.

Consequently, this patch puts the dts-v1 statement into the top-level
SoC-based DTSI files, and removes all other occurences.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes accordingly where necessary.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-25 23:26:40 +02:00
Adrian Schmutzler
41cc7edc15 ath79: move dts-v1 statement to ath79.dtsi
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.

In ath79, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent ath79.dtsi file already determines the DTS version, so
putting it into the DTS files is just a useless repetition.

Consequently, this patch puts the dts-v1 statement into the parent
ath79.dtsi, which is (indirectly) included by all DTS files. All
other occurences are removed.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes to make sure the ath79.dtsi or its
descendants are always included first.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-25 23:26:34 +02:00
Adrian Schmutzler
3ca2d31c54 ath79: move ath79-clk.h include to ath79.dtsi
ath79.dtsi uses ATH79_CLK_MDIO, so the include

  <dt-bindings/clock/ath79-clk.h>

needs to be moved there.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-25 23:24:09 +02:00
Adrian Schmutzler
bdd9dd8ab2 ipq40xx: tidy up dts-v1 statements
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.

Therefore, adding it to a DTS _and_ a DTSI file is actually wrong,
as it will be present twice then (though the compiler does not
complain about it).

In ipq40xx, the dts-v1 statement is already included in
qcom-ipq4019.dtsi, so we don't have to add it anywhere at all.
However, based on the conditions stated above, this requires
qcom-ipq4019.dtsi to be included as the first file in any DTS(I).

Consequently, this patch removes all cases of dts-v1 for the
ipq40xx target, and moves the includes accordingly where necessary.

While at it, remove a few obviously unneeded includes on the way.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-25 21:10:41 +02:00
Adrian Schmutzler
b284333b3a ath79: move engenius_loader_okli recipe before devices
Move engenius_loader_okli image recipe in front of all Engenius
devices, so adding new device entries will not have them sorted
before the shared recipe.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-25 20:07:16 +02:00
Linus Walleij
7e9e6fdac7 gemini: Bring up DSA switches
First group the interfaces on the DSA switch into the
right LAN/WAN groups. Tested successfully on the
D-Link DIR-685 with the RTL8366RB DSA switch.

The RTL8366RB is DSA custom tagged and now handled
by the kernel tag parser. (Backported.)

The Vitesse switches are not capable of supporting
DSA per-port tagging. We suspect they must be handled
using some custom VLAN set-up.

Cc: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[sorted devices alphabetically]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
fa1713e791 ipq40xx: fix DTS warning in qcom-ipq4029-gl-s1300.dts
.dts:226.17-230.4: Warning (spi_bus_reg): /soc/spi@78b6000/spi@1:
	SPI bus unit address format error, expected "0"

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
890bb54d7f ipq40xx: fix DTS warning in qcom-ipq4019-cm520-79f.dts
.dts:121.4-14: Warning (reg_format): /led_spi/led_gpio@0:reg: \
	property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
.dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
.dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
.dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
.dts:119.24-126.5: Warning (avoid_default_addr_size): /led_spi/led_gpio@0: \
	Relying on default #size-cells value

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
0e4092cbad bcm53xx: add Cisco Meraki MR32
This patch adds support for Cisco Meraki MR32.
The unit was donated by Chris Blake. Thank you!

WARNING:
Only the 1x1:1 abgn Air Marshal WIPS wifi is currently supported by b43:
 b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
 b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
 b43-phy2: Loading firmware version 784.2 (2012-08-15 21:35:19)
 and only as 802.11ABG!

while WIFI1 and WIFI2 (both BCM4352) are not:
 b43-phy0: Broadcom 4352 WLAN found (core revision 42)
 b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 12, Type 11 (AC), Revision 1)

Hardware Highlights:

SoC:	Broadcom BCM53016A1 (1 GHz, 2 cores)
RAM:	128 MiB
NAND:	128 MiB Spansion S34ML01G2 (~114 MiB useable)
ETH:	1GBit Ethernet Port - PoE
WIFI1:	Broadcom BCM43520 an+ac (2x2:2 - id: 0x4352)
WIFI2:	Broadcom BCM43520 bgn (2x2:2 - id: 0x4352)
WIFI3:	Broadcom BCM43428 abgn (1x1:1 - id: 43428)

BLE:	Broadcom BCM20732 (ttyS1)
LEDS:   1 x Programmable RGB Status LED (driven by a PWM)
	1 x White LED (GPIO)
	1 x Orange LED Fault Indicator (GPIO)
	2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC:   AT24C64 8KiB EEPROM (i2c - stores Ethernet MAC + Serial#!)
	ina219 hardware monitor (i2c)
	Kensington Lock

SERIAL:
	WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
	The Serial setting is 115200-8-N-1. The board has a populated
	right angle 1x4 0.1" pinheader.
	The pinout is: VCC, RX, TX, GND. (Use a multimeter)

Flashing needs a serial adaptor (due to the lack of a working dropbear on
the original firmware).

This flashing procedure for the MR32 was tested with firmware:
"r23-149867:150252-aacharya".

0. Create a seperate Ethernet LAN which does not have access to the internet.
   Ideally use 192.168.1.2 for your PC. Make sure to reserve 192.168.1.1 it
   will be used later on by the OpenWrt firmware. The original Meraki firmware
   will likely try to setup the network via DHCP Discovery, so make sure your
   PC is running a DHCP-Server (i.e.: dnsmasq)
   '# dnsmasq -i eth# -F 192.168.1.5,192.168.1.50
   Furthermore, the PC needs a supported ssh/http/ftp server in order to
   retrieve the initramfs + dtb file

1. Disassemble the MR32 device by removing all screws (4 screws are located
   under the 4 rubber feets!) and prying open the plastic covers without
   breaking the plastic retention clips. Once inside, remove all the screws
   on the outer metal shielding to get to the PCB. It's not necessary to
   remove the antennas!

2. Connect the serial cable to the serial header.

3. Partially reassemble the outer metal shielding to ensure that the SoC
   has a proper heat sink.

4. Connect the Ethernet patch cable to the device and the power cable.

5. Wait for the device to boot and enter the root shell.
   (rooting is not discussed in detail here please refer to
   Chris Blake - "pwning the meraki mr18" blog post:
   <https://servernetworktech.com/2016/02/pwning-the-meraki-mr18/>
   (The same method works with the MR32's r23-149867:150252-aacharya)

   Wait for the MR32 to enter the "<Meraki>" prompt and enter:
   <Meraki> odm serial_num read
   (Verify that it matches what's on the S/N Sticker on the back!)
   <Meraki> odm serial_num write Q2XX-XXXX-XXXV
   <Meraki> odm serial_num read
   (Verify that the S/N has changed - and the LED start to flash)

   now to flash the firmware:
   <Meraki> odm firmware part.safe "http://192.168.1.2/mr32-initramfs.bin"

Once OpenWrt booted use sysupgrade to permanently install
OpenWrt. To do this: Download the latest sysupgrade.bin file
for the MR32 to the device and use sysupgrade *sysupgrade.bin
to install it.

WARNING: DO NOT DELETE the "storage" ubi volume!

To flash later MR32 Firmwares like r25-201804051805-G885d6d78-dhow-rel
requires in-circut-i2c tools to access the I2C EEPROM AT24C64 next to
the SoC. The idea is pretty much the same as from Step 5 from above:
Change the serial number to Q2XXXXXXXXXV (should be around 0x7c), then
attach a serial cable, ethernet (but make sure the device can't reach
the internet!) hit "s" (the small s!) during boot to enter the root-shell
and add the following commands to the /storage/config there:

serial_allow_odm true
serial_access_enabled true
serial_access_check false
valid_config true

and then hit exit to let it finish booting.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
1291274335 kernel: package bcm53xx i2c module
The BCM5301x SoCs do have i2c. Since this is only
being used by the Meraki MR32, this will be packaged
as a module.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
abe46d5002 kernel: add default for new config symbols
Provide disabled defaults for I2C_SLAVE_EEPROM and IPMB_DEVICE_INTERFACE.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
5f610ec4b8 bcm53xx: backport uart2 and pcie2 device-nodes
These have made their way into -next. This patch
also includes the portion of the bcm53xx kernel
patch refreshes as the hunks in
302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch
moved slightly due to the added nodes.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
c6d9a2ac59 bcm53xx: enable PWM for bcm53xx
The Meraki MR32 (BCM53016A1) uses the pwm to drive the
tricolor LED. The driver has been available in upstream
for a long time. Only the Device-Tree definition was
missing, but it has been queued recently.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:33 +02:00
Hans Geiblinger
a9071d02b5 ipq40xx: Add support for Linksys MR8300 (Dallas)
The Linksys MR8300 is based on QCA4019 and QCA9888
and provides three, independent radios.
NAND provides two, alternate kernel/firmware images
with fail-over provided by the OEM U-Boot.

Hardware Highlights:

SoC: IPQ4019 at 717 MHz (4 CPUs)
RAM: 512MB RAM

SoC:	Qualcomm IPQ4019 at 717 MHz (4 CPUs)
RAM:	512M DDR3
FLASH:	256 MB NAND (Winbond W29N02GV, 8-bit parallel)
ETH:	Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks)
BTN:	Reset and WPS
USB:	USB3.0, single port on rear with LED
SERIAL:	Serial pads internal (unpopulated)
LED:	Four status lights on top + USB LED
WIFI1:	2x2:2 QCA4019 2.4 GHz radio on ch. 1-14
WIFI2:  2x2:2 QCA4019 5 GHz radio on ch. 36-64
WIFI3:  2x2:2 QCA9888 5 GHz radio on ch. 100-165

Support is based on the already supported EA8300.
Key differences:
	EA8300 has 256MB RAM where MR8300 has 512MB RAM.
	MR8300 has a revised top panel LED setup.

Installation:
"Factory" images may be installed directly through the OEM GUI using
URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1)

Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com>
[copied Hardware-highlights from EA8300. Fixed alphabetical order.
fixed commit subject, removed bogus unit-address of keys,
fixed author (used Signed-off-By to From:) ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:31:51 +02:00
Tomasz Maciej Nowak
e24635710c ipq40xx: add support for Luma Home WRTQ-329ACN
Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band
wireless access point.

Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 2 MB SPI NOR
       128 MB SPI NAND
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R integrated
Ethernet: 2x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus
LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU
Buttons: 1x GPIO controlled
EEPROM: 16 Kbit, compatible with AT24C16
UART: row of 4 holes marked on PCB as J19, starting count from the side
      of J19 marking on PCB
      1. GND, 2. RX, 3. TX, 4. 3.3V
      baud: 115200, parity: none, flow control: none

The device supports OTA or USB flash drive updates, unfotunately they
are signed. Until the signing key is known, the UART access is mandatory
for installation. The difficult part is disassembling the casing, there
are a lot of latches holding it together.

Teardown
Prepare three thin, but sturdy, prying tools. Place the device with back
of it facing upwards. Start with the wall having a small notch. Insert
first tool, until You'll feel resistance and keep it there. Repeat the
procedure for neighbouring walls. With applying a pressure, one edge of
the back cover should pop up. Now carefully slide one of the tools to
free the rest of the latches.
There's no need to solder pins to the UART holes, You can use hook clips,
but wiring them outside the casing, will ease debuging and recovery if
problems occur.

Installation
1. Prepare TFTP server with OpenWrt initramfs image.
2. Connect to UART port (don't connect the voltage pin).
3. Connect to LAN port.
4. Power on the device, carefully observe the console output and when
   asked quickly enter the failsafe mode.
5. Invoke 'mount_root'.
6. After the overlayfs is mounted run:
     fw_setenv bootdelay 3
   This will allow to access U-Boot shell.
7. Reboot the device and when prompted to stop autoboot, hit any key.
8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
   'setenv' to do that, then run following commands:
     tftpboot 0x84000000 <openwrt_initramfs_image_name>
     bootm 0x84000000
   and wait till OpenWrt boots.
9. In OpenWrt command line run following commands:
     fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000"
     fw_setenv bootcmd "run openwrt"
10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
    with:
     ubirmvol /dev/ubi0 -N ubi_rootfs
     sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name>
11. After flashing, the access point will reboot to OpenWrt, then it's
    ready for configuration.

Reverting to OEM firmware
1. Execute installation guide steps: 1, 2, 3, 7, 8.
2. In OpenWrt command line run following commands:
     ubirmvol /dev/ubi0 -N rootfs_data
     ubirmvol /dev/ubi0 -N rootfs
     ubirmvol /dev/ubi0 -N kernel
     ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs
     ubimkvol /dev/ubi0 -S 34 -N kernel1
     ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1
     ubimkvol /dev/ubi0 -S 264 -N rootfs_data
     fw_setenv bootcmd bootipq
3. Reboot.

Known issues
The LEDs ring doesn't have any dedicated driver or application to control
it, the only available option atm is to manipulate it with 'i2cset'
command. The default action after applying power to device is spinning
blue light. This light will stay active at all time. To disable it
install 'i2c-tools' with opkg and run:
 i2cset -y 2 0x48 3 1 0 0 i
The light will stay off until next cold boot.

Additional information
After completing 5. step from installation guide, one can disable asking
for root password on OEM firmware by running:
 sed -e 's/root/root::/' -i /etc/passwd
This is useful for investigating the OEM firmware. One can look
at the communication between the stock firmware and the vendor's
cloud servers or as a way of making a backup of both flash chips.
The root password seems to be constant across all sold devices.
This is output of 'led_ctl' from OEM firmware to illustrate
possibilities of LEDs ring:

Usage: led_ctl [status | upgrade | force_upgrade | version]
       led_ctl solid    COLOR <brightness>
       led_ctl single   COLOR INDEX <brightness 0 - 15>
       led_ctl spinning COLOR <period 1 - 16 (lower = faster)>
       led_ctl fill     COLOR <period 1 - 16 (lower = faster)>
                                             ( default is 5 )
       led_ctl flashing COLOR <on dur 1 - 128>  <off dur 1 - 128>
                              (default is  34)  ( default is 34 )
       led_ctl pulsing  COLOR
COLOR: red, green, blue, yellow, purple, cyan, white

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit,
changed ubi volumes for easier integration, slightly reworded
commit message, changed ubi volume layout to use standard names all
around]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:30:19 +02:00
Brian Norris
03bc9b0002 ipq40xx: add open-drain support to pinctrl-msm
Submitted upstream. Shouldn't affect existing devices, but enables new
device support.

https://lore.kernel.org/linux-gpio/20200703080646.23233-1-computersforpeace@gmail.com/

Currently queued for-next:
https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git/commit/?h=for-next&id=13355ca35cd16f5024655ac06e228b3c199e52a9

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[refresh patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 18:43:09 +02:00
John Audia
3ea1b5b745 kernel: bump 5.4 to 5.4.67
All modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x, lantiq/xrx200 and ath79/generic
Run-tested: ipq806x (R7800), lantiq (Easybox 904 xDSL)

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[add test on lantiq]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-24 18:53:23 +02:00
J. Scott Heppler
620f9c7734 ramips: add support for Linksys EA7300 v2
This submission relied heavily on the work of
Santiago Rodriguez-Papa <contact at rodsan.dev>

Specifications:

*  SoC:            MediaTek  MT7621A            (880  MHz  2c/4t)
*  RAM:            Winbond W632GG6MB-12         (256M  DDR3-1600)
*  Flash:          Winbond W29N01HVSINA         (128M  NAND)
*  Eth:            MediaTek  MT7621A            (10/100/1000  Mbps  x5)
*  Radio:          MT7603E/MT7615N              (2.4  GHz  &  5  GHz)
                     4  antennae:  1  internal  and  3  non-deatachable
*  USB:            3.0  (x1)
*  LEDs:
          White    (x1  logo)
          Green    (x6  eth  +  wps)
          Orange   (x5,  hardware-bound)
*  Buttons:
          Reset    (x1)
          WPS      (x1)

Installation:

Flash factory image through GUI.

This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.

Reverting to factory firmware:

Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.

Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
2020-09-23 12:17:32 +02:00
Adrian Schmutzler
0cfdc7d446 target: update SPDX license names
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-22 20:58:26 +02:00
Paul Spooren
e8f61bf50d ath79: remove DTS from ATH79 target name
The legacy ar71xx target is removed and multiple targets use DTS now, so
there is no need to point that out for ATH79 specifically.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-09-22 20:29:24 +02:00
Chuanhong Guo
006cd489f0 mediatek: mt7622: select bluetooth module instead of firmware
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-22 21:13:54 +08:00
Chuanhong Guo
20f2bd044a mediatek: build btmtkuart as a kernel module
bluetooth on mt7622 needs a firmware to start. It can't be built-in or
it tries to load firmware before rootfs is mounted, and then fails.
build it as a kernel module to fix that.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-22 21:07:50 +08:00
David Woodhouse
7190fb2da4 mediatek: mt7623: use bash for generating bootable images
It turns out that 'echo -e' isn't portable; it doesn't work in the dash
builtin echo and Ubuntu users are complaining.

I can't even get octal (specified by POSIX) to work consistently because
those  variants of 'echo' which *do* support -e don't seem to interpret
octalwithout it.

I could switch to /bin/echo but using -e with that isn't actually
portable *either* even though it works today.

For now just stick with bash, and use its builtin. We may end up using
something else entirely; perhaps perl.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-09-19 13:39:29 +01:00
David Woodhouse
d10b738c4b mediatek: fix missing pause on switch port for Banana Pi R2
This causes rx drops when running iperf.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-09-19 13:39:29 +01:00
Adrian Schmutzler
95c9df7971 ipq806x: fix support of Edgecore ECW5410 support
This fixes several stylistic and functional errors of the recently
added Edgecore ECW5410:

  - fix call in 11-ath10k-caldata
  - use hex notation in 11-ath10k-caldata
  - remove redundant definitions from DTS that are already in DTSI
  - use proper sorting in image/Makefile
  - use DEVICE_VENDOR/DEVICE_MODEL instead of DEVICE_TITLE
  - use SOC instead of DEVICE_DTS

Fixes: 59f0a0fd839e ("ipq806x: add Edgecore ECW5410 support")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-19 13:32:11 +02:00
John Audia
770a9c6787 kernel: bump 5.4 to 5.4.66
All modifications made by update_kernel.sh/no manual intervention needed

Run-tested: ipq806x (R7800), ath79 (Archer C7v5), x86/64

No dmesg regressions, everything appears functional

Signed-off-by: John Audia <graysky@archlinux.us>
[add run test from PR]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-19 12:41:29 +02:00
John Thomson
bf2870c1d9 kernel: fix mtd partition erase < parent_erasesize writes
This bug applied where mtd partition end address,
or erase start address, was not cleanly divisible by parent mtd erasesize.

This error would cause the bits following the end of the partition
to the next erasesize block boundary to be erased,
and this partition-overflow data to be written to the partition erase
address (missing additional partition offset address)
of the mtd (top) parent device.

Fixes: FS#2428

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[shorten commit title, add Fixes, fix kernel 4.19 as well]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-19 12:41:29 +02:00
Roger Pueyo Centelles
e6b42386ba ath79/mikrotik: fix soft_config location for SXT 5n
The soft_config partition for these devices lays between 0xe000 and
0xf000 (as correctly detected by the RouterBoard platform driver),
before the bootloader2 partition which starts at 0x10000.

This commit correctly sorts the partitions, fixing the parsing error.

Fixes: FS#3314

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-09-17 23:52:03 +02:00
Martin Schiller
a594a5a330 lantiq: use uniform "u-boot-env" mtd label
This is the most popular choice in the linux kernel tree.

Within OpenWrt, this change will establish consistency with ath79
and ramips targets.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[extend commit message, include netgear_dm200, update base-files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 21:09:51 +02:00
Vladimir Vid
9f0d882680 mvebu: image: add check for fdt_add_r and kernel_addr_r variables
fdt_addr and kernel_addr variables are getting obsolete in the mainline
u-boot in favor of fdt_addr_r and kernel_addr_r.

By checking if the new variables exist, we can make sure that devices with newer
version of u-boot will work while not breaking support for the existing ones.

Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-09-17 21:09:51 +02:00
Felix Fietkau
4fb58813f9 mediatek: fix hardware flow offload
Add support for dealing with DSA ports

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-17 21:08:32 +02:00
David Bauer
056945faa4 ipq40xx: enable FRITZRepeater 3000 ports on switch
The ethernet ports on the AVM FRITZRepeater 3000 are not separated
between LAN and WAN in the stock firmware. OpenWrt currently abstracts
port 4 as eth0 and port 5 as eth1, bridging them in the kernel.

This patch adjusts the GMAC port bitmasks and default bitmask for ar40xx
to bridge them on the switch, avoiding traffic on both ports to pass
thru the CPU.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-17 18:08:46 +02:00
David Bauer
b7da0d2944 ath79: add support for Ubiquiti UniFi AP Pro
This adds support for the Ubiquiti UniFi AP Pro to the ath79 target. The
device was previously supported on the now removed ar71xx target.

SoC   Atheros AR9344
WiFi  Atheros AR9344 & Atheros AR9280
ETH   Atheros AR8327
RAM   128M DDR2
FLASH 16M SPI-NOR

Installation
------------

Follow the Ubiquiti TFTP recovery procedure for this device.

1. Hold down the reset button while connecting power for 10 seconds.
2. Transfer the factory image via TFTP to the AP (192.168.1.20)
3. Wait 2 minutes for the AP to write the firmware to flash. The device
   will automatically reboot to OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-17 18:07:39 +02:00
Adrian Schmutzler
6e170ffb96 ipq806x: sort entries in lib/upgrade/platform.sh
Apply alphabetic sorting like in the other files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 13:03:18 +02:00
Adrian Schmutzler
0b1cdb7eea treewide: remove empty default cases
There is no apparent reason to have an empty default case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 12:46:19 +02:00
Adrian Schmutzler
a744c14dfa ipq806x: sort entries in 02_network
Apply alphabetic sorting like in the other files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 12:33:45 +02:00
John Crispin
0fbdb51f76 ipq40xx: add Edgecore OAP-100 support
flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
  - tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
  - ubiattach -p /dev/mtd0
  - ubirmvol /dev/ubi0 -n0
  - ubirmvol /dev/ubi0 -n1
  - ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
  - sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin

Signed-off-by: John Crispin <john@phrozen.org>
2020-09-17 08:43:07 +02:00
Robert Marko
4488b260a0 ipq40xx: add Edgecore ECW5211 support
This patch adds support for the Edgecore ECW5211 indoor AP.

Specification:
- SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7
- RAM: 256MB DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB MX35LFxGE4AB SPI-NAND
- Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn)
- CC2540 BLE connected to USB 2.0 port
- Atmel AT97SC3205T I2C TPM

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:43:03 +02:00