This reverts commit f536f5ebdd.
As Hauke commented, this causes builder failures on 5.4 kernels.
This revert includes changes to the mx100 kernel modules
dependency as well as the uci led definitions.
Tested-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds a userspace interpretation of the nu801 driver used by Meraki
hardware. Previously this was a driver that was added per target, but as
multiple targets now have this driver, we should move to something that
can be shared by all targets since no driver exists upstream.
Co-developed-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kernel has added the different variants of the Rock Pi 4 in commit
b5edb0467370 ("arm64: dts: rockchip: Mark rock-pi-4 as rock-pi-4a
dts"). The former Rock Pi 4 is now Rock Pi 4A.
For compatibility with kernel 5.4, this rename has been held back
so far. Having switched to kernel 5.10 now, we can finally apply
it in our tree as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The GPIO_DEVICE symbol belonged to a custom driver that was removed from
OpenWrt in 2012. The symbol never existed in the upstream kernel.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update busybox to version 1.34.1, which is a minor
maintenance release. It contains just the two post-1.34.0
upstream patches that we earlier backported plus a few fixes
to awk.
* Remove the two backported upstream patches that are
now unnecessary.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
U-Boot 2021.10 has been released.
Rebase mediatek patches on top of new release and remove some patches
which have been merged upstream.
Tested on Bananapi BPi-R2 (mt7623), Bananapi BPi-R64 (mt7622) and
Linksys E8450 (mt7622).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Bring the usage in line with the dnsmasq man page and the other options
where set: is mandatory.
No functional change.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Nobody ever updates PKG_RELEASE when changing devices or setup in
the various uboot-* packages. Use $(AUTORELEASE) so we still have
proper versioning there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This simplifies some operations as it doesn't have to be caculated over
and over. It will also allow adding support for more vendor formats.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Globalscale MOCHAbin is a Armada 7040 based development board.
Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element
Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.
Installation:
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/
$ in.tftpd -L -s bin/targets/mvebu/cortexa72/
Connect to the device UART via microUSB port and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Set the ethernet device (Example for the 1G WAN):
$ setenv ethact mvpp2-2
Ping server to confirm network is working:
$ ping $serverip
Using mvpp2-2 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin
$ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb
Boot the image:
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Hit any key to stop the autoboot.
Reset U-boot env and set the bootcmd:
$ env default -a
$ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}'
Optionally I would advise to edit the console env variable to remove earlycon as that
causes the kernel to never use the driver for the serial console.
Earlycon should be used only for debugging before the kernel can configure the console
and will otherwise cause various issues with the console.
$ setenv console 'console=ttyS0,115200'
Save and reset
$ saveenv
$ reset
OpenWrt should boot from eMMC now.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Fix BPi-R2 GPIO LEDs to indicate boot into production or recovery
firmware in DTS and define them in default environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
186f6eaeba70 wireless: display log messages for setup/teardown/retry
fac471c4934a wireless: process and close script file descriptor when rerunning setup
62e2bb56f48e main: poll process log stream even if processes are killed
0e311d3f2d1a wireless: reset number of retries on config change
e467e0ff44c0 wireless: reset retry counter when setup succeeds
448ffc154fe7 wireless: fix index for stations
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Even though TRACEPOINTS is not enabled in my kernel config, my build
fails due to KVM_MMU_AUDIT being missing. Add this symbol to kmod-kvm to
fix this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
In hostapd_ubus_add_bss(), ubus objects are not registered for mesh
interfaces. This provokes a segfault when accessing the ubus object in
mesh deinit.
This commit adds the same condition to hostapd_ubus_free_bss() for
discarding those mesh interfaces.
Signed-off-by: Jesus Fernandez Manzano <jesus.manzano@galgus.net>
The `mkdir` commands supports passing multiple arguments to batch create
multiple folders, instead of calling the tool every single time.
If the creation of one of the folders fails, all other folder are still
created and therefore doesn't change the error handling.
Also stop creating `/etc/` explicitly after subfolders of `/etc/` were
already created.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The `sed`-script shouldn't be called multiple times, especially not with
the same files.
This commit merges all files together in a single `sed`-script call.
Signed-off-by: Paul Spooren <mail@aparcar.org>
For some reason, the build system chops off the last number from the version,
which is not correct. Add it back.
Update hash.
Fixes: 96c7164acd ("restool: update to LSDK-20.12")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[add Fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The official Plasma Cloud firmware adjusted the BDFs to contain new
conformance test limits and target power values. These should be imported
to avoid emissions outside the allowed limits.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Currently, the fstab service starts after the log service which breaks
the ability to write a persistent log file to a filesystem mounted by
the fstab service. Thus, change the start order of the fstab service so
it starts right before the log service.
Fixes: b131853 ("ubox: update to latest git revision")
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
[set to 11 to be explicitly before log, not only alphabetically, SPDX]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Fixes compilation with GCC11.
Kept PKG_VERSION as there's some bug that chops off the 12 at the end.
Refreshed other patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Fixes compilation with both GCC 10 and 11.
Switched to AUTORELEASE for simplicity.
Removed PKG_VERSION as it's derived from PKG_SOURCE_VERSION.
Removed all patches as they are upstream backports.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Delete tunnel on 6rd interface teardown.
Should solve problem related to tunnel stuck on restart loop
with "Unknown Command" on tunnel restart due to wan connection drop.
This patch is similar to the one written by Ansuel on Aug 2, 2021
but the 6rd teardown produces the same symptoms when the network
service is restarted.
Signed-off-by: David Lam <david@thedavid.net>
GCC 10 defaults to `-fno-common` and complains about multiple definition
of `mc_status` in restool.
Backport a patch from upstream to fix compilation with host GCC 10.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
c62d85cf7a0d bridge: check port bpdu filter status and apply it to the config
25555611be91 libnetlink: turn rtnetlink error answers into debug msgs
462b3a491347 build: use pthread cflags/ldflags
Signed-off-by: Felix Fietkau <nbd@nbd.name>
d590fbd255ce wireless: always enable bpdu filter for AP interfaces and VLANs
f8ff6d820283 system-linux: remove copy&paste from /proc and /sys path names
300b1220fab3 wireless: improve reliability of proxyarp support
5ba9744aac6d device: add support for configuring bonding devices
6fa9b042ff4d wireless: only apply wireless device attributes to the base vif interface
06d11bbf1f2b wireless: only enable proxyarp/isolate for AP vifs
08e954e137ff bonding: claim the port device before creating the bonding device
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds the hash also for the aarch64 toolchain in addition to the
x86_64 toolchain. This gets the build on a Linux aarch64 host one step
further.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update iproute2 to latest stable 5.14; for the changes see https://lwn.net/Articles/867940/
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
8a60e7e trace: don't leak file descriptor in error path
68df9ac procd: fix container deletion
f16abe0 uxc: add JSON output option for 'list' command
a23c888 jail: prepare for adding process to existing namespace
50da8a4 instance: allow jailed service to join namespace(s)
482d1ab Revert "jail: do not hack /etc/resolv.conf on container rootfs"
1eb4371 jail: start ubus and netifd instances for container with netns
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
bump version and remove patches that have been applied
176d701 wtmi: Wait 1s after putting PHYs INTn pin low
2eeccfe wtmi: Change comment describing reset workaround
e8c94a5 wtmi: Count RAM size from both CS0 and CS1
995979e wtmi: Rename macro
e29eb29 wtmi: soc: Fix start_ap_workaround() for TF-A with debug
81245ed wtmi: Use constant name PLAT_MARVELL_MAILBOX_BASE
18ccb83 wtmi: Do a proper UART reset with clock change as described in spec
15ff106 avs: Validate VDD value from OTP
3f33626 fix: clock: a3700: change pwm clock for 600/600 and 1200/750 preset
fb5e436 wtmi: uart: fix UART baudrate divisor calculation
Signed-off-by: sean lee <ilf@live.com>
Summary of upstream CHANGELOG:
* Handle DHCPREBIND requests in the DHCPv6 server code.
* Fix bug which caused dnsmasq to lose track of processes forked.
* Major rewrite of the DNS server and domain handling code.
* Revise resource handling for number of concurrent DNS queries.
* Improve efficiency of DNSSEC.
* Connection track mark based DNS query filtering.
* Allow smaller than 64 prefix lengths in synth-domain.
* Make domains generated by --synth-domain appear in replies
when in authoritative mode.
* Ensure CAP_NET_ADMIN capability is available when
conntrack is configured.
* When --dhcp-hostsfile --dhcp-optsfile and --addn-hosts are
given a directory as argument, define the order in which
files within that directory are read.
* Support some wildcard matching of input tags to --tag-if.
Signed-off-by: Etan Kissling <etan.kissling@gmail.com>
Changes from 4.7.0:
Fix one high (OCSP verification issue) and two low vulnerabilities
Improve compatibility layer
Other improvements and fixes
For detailed changes refer to https://github.com/wolfSSL/wolfssl/releases
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HPv2
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: W631GG8MB-12 128 MiB DDR3 SDRAM
(stock firmware is configured to use only 64 MiB)
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
24 ethernet port PoE status LEDs
2 SFP status/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESTORE" button on front panel
1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J41) with populated standard pin connector on
the left edge of the PCB, angled towards the side.
The casing has a rectangular cutout on the side that provides
external access to these pins.
Pinout (front to back):
+ GND
+ TX
+ RX
+ VCC
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
OEM upgrade method:
(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
The ipq-wifi-netgear_wac510 package is not selected by any device and would
be empty anyway. The default board-2.bin from ath10k-board-qca4019 is
therefore used for this device and the package doesn't provide any visible
features.
Fixes: b126d9c3a3 ("ipq40xx: add netgear wac510 support")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When doing parallel build on a fast machine with bottleneck in i/o,
m_xt.so may start linking faster than dynsyms.list gets populated,
resulting in error:
ld:dynsyms.list:0: syntax error in dynamic list
Fix this by adding dynsyms.list as make dependency to m_xt.so
Described also here:
https://bugs.openwrt.org/index.php?do=details&task_id=3353
Change from v1:
- add dynsysms.list dependancy only when shared libs are enabled
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Fixes: FS#3353
Christian Lamparter
Chris Blake
Adrian Schmutzler
Ronny Kotzschmar
Stijn Tintel
Hannu Nyman
Daniel Golle
Paul Fertser
Rafał Miłecki
Robert Marko
Alan Swanson
Felix Fietkau
Rosen Penev
Jesus Fernandez Manzano
Paul Spooren
Sven Eckelmann
Timo Sigurdsson
Hauke Mehrtens
David Lam
Kuan-Yi Li
Hans Dedecker
sean lee
Etan Kissling
Ivan Pavlov
Soma Zambelly
Christian Pointner
Roman Yeryomin