Remove upstreamed from 2.11 release:
060-nl80211-fix-crash-when-adding-an-interface-fails.patch
Rebase all other patches
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16338
Signed-off-by: Robert Marko <robimarko@gmail.com>
Release 2.11 has been quite a few new features and fixes since the 2.10
release. The following ChangeLog entries highlight some of the main
changes:
* Wi-Fi Easy Connect
- add support for DPP release 3
- allow Configurator parameters to be provided during config exchange
* HE/IEEE 802.11ax/Wi-Fi 6
- various fixes
* EHT/IEEE 802.11be/Wi-Fi 7
- add preliminary support
* SAE: add support for fetching the password from a RADIUS server
* support OpenSSL 3.0 API changes
* support background radar detection and CAC with some additional
drivers
* support RADIUS ACL/PSK check during 4-way handshake (wpa_psk_radius=3)
* EAP-SIM/AKA: support IMSI privacy
* improve 4-way handshake operations
- use Secure=1 in message 3 during PTK rekeying
...and many more
Remove upstreamed patches:
023-ndisc_snoop-call-dl_list_del-before-freeing-ipv6-add.patch
030-driver_nl80211-rewrite-neigh-code-to-not-depend-on-l.patch
040-mesh-allow-processing-authentication-frames-in-block.patch
181-driver_nl80211-update-drv-ifindex-on-removing-the-fi.patch
182-nl80211-move-nl80211_put_freq_params-call-outside-of.patch
183-hostapd-cancel-channel_list_update_timeout-in-hostap.patch
210-build-de-duplicate-_DIRS-before-calling-mkdir.patch
253-qos_map_set_without_interworking.patch
751-qos_map_ignore_when_unsupported.patch
800-SAE-Check-for-invalid-Rejected-Groups-element-length.patch
801-SAE-Check-for-invalid-Rejected-Groups-element-length.patch
802-SAE-Reject-invalid-Rejected-Groups-element-in-the-pa.patch
Other patches has been updated.
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16338
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- Device: DNA Valokuitu Plus EX400
- SoC: MT7621A
- Flash: 256MB NAND
- RAM: 256MB
- Ethernet: Built-in, 2 x 1GbE
- Wifi: MT7603 2.4 GHz, MT7615 5 GHz (4x internal antennas)
- USB: 1x 3.0
- LED: 1x green/red, 1x green
- Buttons: Reset
MAC addresses:
- LAN: u-boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access booting can be halted to U-boot by pressing any
key. TFTP and flash writes are available, but only the first one has been
tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI install the OpenWrt factory image. Alternatively,
ssh to the device and use sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Known issues:
- MACs for wifi are stored in currently unknown place but it seems
to persist over power-off. They might be stored on the chip.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
[rmilecki: try NVMEM for MACs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
- specify CC target explicitly
- define KBUILD_SYM32=n to select "native" build format (if building with 64-bit arch)
- rewrap lines (for good)
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15702
Signed-off-by: Robert Marko <robimarko@gmail.com>
The path for linking libucode.so was not specified for the ucode binary.
This breaks execution of ucode in the host context.
Signed-off-by: David Bauer <david.bauer@uniberg.com>
move nanopc-t6 recipes above rock 5b.
Fixes: 9482341a47 ("rockchip: add support for nanopc t6")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16340
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: QCA8081 (10/100/1000/2.5GBASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2,
and 3 respectively. Be sure to crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.10.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: George Witt <george.witt@nltsproject.org>
Link: https://github.com/openwrt/openwrt/pull/15832
Signed-off-by: Robert Marko <robimarko@gmail.com>
GCC errors on returning int in void function now.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16348
Signed-off-by: Robert Marko <robimarko@gmail.com>
OpenSSL 3.0.15 is a security patch release. The most severe CVE fixed in this release is Moderate.
This release incorporates the following bug fixes and mitigations:
* Fixed possible denial of service in X.509 name checks (CVE-2024-6119)
* Fixed possible buffer overread in SSL_select_next_proto() (CVE-2024-5535)
Added github releases url as source mirror
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16332
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds u-boot config for access to system env variables on this board
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If the user has ip-tiny or ip-full installed there is no need to depend on
BusyBox having any form of `ip` or `ip link` applets.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Link: https://github.com/openwrt/openwrt/pull/16062
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Include hotfix suggested by Sebastian Gottschall to fix bug introduced
with APuP patchset
Signed-off-by: Gioacchino Mazzurco <gio@polymathes.cc>
Link: 0c3001a69e
Link: https://github.com/openwrt/openwrt/pull/16298
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of avoiding returning, propagate error so that the kernel
infrastructure can handle it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of ignoring errors, let the linux infrastructure handle it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Besides probing BPF information in running system, bpftool is also used in
generating skeleton, dumping BTF, etc. that is widely used in modern BPF
development. Make it available as a host tool so that we can use it in
package build.
Tested build targeting malta/le on Arch Linux x86_64. bpftools currently
does not support processing cross-endian BPF objects, so big-endian host
is needed to build for big-endian targets using bpftools.
Signed-off-by: Eric Long <i@hack3r.moe>
Link: https://github.com/openwrt/openwrt/pull/16122
Signed-off-by: Robert Marko <robimarko@gmail.com>
480551a3adc4 interface: add support for disabling renew on topology change
b7b294266781 device: add more debugging code
595094f5c213 device: do not pull device present state from hotplug events
4e11e52e9b98 main: add messages to udebug regardless of their log level
091d063f4a9d wireless: handle link updates even if devices are present already
a8e90853c936 interface: improve hotplug handling reliability
cdb41673ceea device: remove redundant newlines from debug messages
cd2a7964f2c0 device: revert to explicit device_set_present calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Try to do a clean disconnection via L3 request before the connection is
stopped.
Because this might take up to 6 seconds (the driver does 3 attempts with
a timeout of 2 seconds each), a termination timeout needs to be defined
in the init script.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Move the code for disconnection on exit to a separate function, and also
call it in the code paths for SIGINT and the "quit" CLI command.
While at it, make the patch description a bit clearer.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Move the code for disconnection on exit to a separate function, and also
call it in the code path for the "quit" CLI command.
While at it, make the patch description a bit clearer.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Use the correct return value in error message.
Fixes: 6e4c9738be ("ltq-vdsl-vr11-app: add version 4.23.1 for vr11 targets")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Use the correct return value in error message.
Fixes: 1daaef31b3 ("ltq-vdsl-app: disconnect when service is stopped")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Empty trailing fields get lost when the lines are split and merged again
at colons, resulting in unparsable entries. Only use the split fields for
matching against the other file, but emit the original line unchanged
to fix the issue.
Fixes: de7ca7dafa ("base-files: merge /etc/passwd et al at sysupgrade config restore")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* Adds the x86_64 dependency for mlxsw_core
* Removes the redundant mlxsw_core dependency
from mlxsw-minimal and mlxsw-spectrum
* Removes the DCB configuration symbols because
they were moved into the generic configuration
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the currently missing Mellanox
Spectrum-2, Spectrum-3, and Spectrum-4 firmware files.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the missing x86 dependency for
the Mellanox mlxcpld LED driver.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3B is a Pico-ITX form factor SBC[1] using the Rockchip
RK3568(J).
Hardware
--------
- Rockchip RK3568(J) SoC
- Quad A55 CPU
- Mali-G52 GPU
- 1 TOPS @ INT8 NPU
- 2GB/4GB/8GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key (2-lane PCIe 3.0)
- SPI Flash for bootloader
- 2x Gigabit ethernet port (one supports PoE with add-on PoE HAT)
- 1x M.2 E Key socket with SDIO, UART and USB interfaces
- 1x M.2 B Key socket with PCIe, SATA, and USB interfaces
- 1x SIM card socket
- 1x USB 3.0 Type-A HOST port
- 1x USB 3.0 Type-A OTG port
- 2x USB 2.0 Type-A HOST ports
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3b
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3C is a high-performance, low-cost SBC[1] using the
Rockchip RK3566.
Hardware
--------
- Rockchip RK3566 SoC
- Quad A55 CPU
- Mali-G52-2EE GPU
- 1 TOPS @ INT8 NPU
- 1GB/2GB/4GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key connector(2230) or M.2 Extension
board(2232/2260/2280)
- SATA through the Radxa Penta SATA HAT
- 1x Gigabit ethernet port(supports PoE with add-on PoE HAT)
- WiFi6/BT5.4 (not supported yet on OpenWrt)
- 1x USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- 1x USB 2.0 Type-A OTG port
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3c
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes the list delimiter between 3GPP networks
passed to hostapd.
> list iw_anqp_3gpp_cell_net '262,001'
> list iw_anqp_3gpp_cell_net '262,002'
When passing a list of "iw_anqp_3gpp_cell_net" parameters via UCI,
hostapd would crash at startup:
> daemon.err hostapd: Line 73: Invalid anqp_3gpp_cell_net: 262,001:262,002
Using a semicolon as a delimiter, hostapd will start as expected.
Signed-off-by: Sarah Maedel <git@tbspace.de>
28b48a1 uim: add support for ICC communication channel
f582e00 qmi: fix dynamic array macro
d381f80 data: add support for ICC channel
Signed-off-by: David Bauer <mail@david-bauer.net>
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.
This commit aligns the casing of Zyxel everywhere.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
