* Add files via upload
* Update VORON2_stock_250_printer.cfg
added extra text at the top of the file and removed a couple of macros to keep it as simple and avoid any confusion for new users
* Increase idle timeout to 24 hours, and set motors to turn off.
* Set electronics fan min PWM and blip time because my fans are sluggish.
* Extruder drive current adjustments based on PA trials to avoid skipping steps.
* Preheat scripts used the wrong fan control command. And fix some temps.
* Make toolhead heater selection sticky by writing out /sys/restore_tool_heater.g.
* Reduce default PLA print temp.
* Make firmware retraction profile selection sticky by writing out to /sys/restore_retraction.g.
Make separate profiles for V6 and Volcano.
* Filament sensors need to be _turned on_.
* Release notes.
* Pulling in comments from public branch.
* Adding named heatbreak thermistor.
* Increasing instantaneous drive parameters on XY
* Turn off extruder drive in print_end.g
* Tweaking mswitch_xy.g position.
* Missed configuration on the heatbreak thermistor.
* Changed origin coordinates to be at bed center.
* Deselect and re-select tool across pause. (Set to standby temp.)
* Set bed standby temps in preheat scripts.
* Add a script for calibrating the mswitch.
* Reduce instantaneous XY drive parameters.
* Increasing pressure advance values for Volcano.
* Full-speed chamber fan on print end.
* Adding another toolhead profile.
* Adding a coarse leveling script for when the gantry is too far out to be corrected by the default dive height.
* Move toolhead thermistor parameters to the heating/toolhead_* scripts, because they change when you swap toolheads.
* README.txt
* README.txt
* FSR Z endstop.
* Don't disable heaters during Z probing. Turns out it's actually not needed and the thermal delta actually messes up the readings.
* README.txt
* Moving daveidmx config from DuetWifi folder to Duet folder.
* MKS Gen L v1.0 brackets
Both orientations. Original hole spacing 102x76mm, scaled to 100.25% to deal with ABS+ shrink (tested on version with long side to the extrusion.)
* Move STLs into their own directory.
* MKS GenL v1.0 brackets, STEP files.
* M3 cable tie clip
Add small M3 cable tie clip, designed to fit onto the bottom extrusions under the coroplast.
* Mains plug panel with RJ45
Two new versions of the mains plug panel, one with the ethernet socket on the left, and one on the right (the 'alternative')
* Create README.md
* Create m4_small_cable_tie_mount.stl
Add M4 variant
* Rename f3d file
* Create README.md
* Add STEP files
* Add 5mm slot cover clips
* Add files via upload
* Delete Fan_cover_21.STL
* Create Readme
* Add files via upload
* Delete Readme
* Delete Fan_cover_4holes.STL
* Delete Fan_cover_2holes.STL
* Create empty
* New covers for V2.1
2 holes for hotend fans and 4 holes for side skirt fans...
* Delete empty
* Delete Fan_cover_2holes.STL
* Delete Fan_cover_4holes.STL
* Create Fan_covers
* New Fan Covers for V2.1
2 holes for hotend fan and 4 holes for side skirt fans
* Uploaded STEP files
* Increase idle timeout to 24 hours, and set motors to turn off.
* Set electronics fan min PWM and blip time because my fans are sluggish.
* Extruder drive current adjustments based on PA trials to avoid skipping steps.
* Preheat scripts used the wrong fan control command. And fix some temps.
* Make toolhead heater selection sticky by writing out /sys/restore_tool_heater.g.
* Reduce default PLA print temp.
* Make firmware retraction profile selection sticky by writing out to /sys/restore_retraction.g.
Make separate profiles for V6 and Volcano.
* Filament sensors need to be _turned on_.
* Release notes.
* Pulling in comments from public branch.
* Adding named heatbreak thermistor.
* Increasing instantaneous drive parameters on XY
* Turn off extruder drive in print_end.g
* Tweaking mswitch_xy.g position.
* Missed configuration on the heatbreak thermistor.
* Changed origin coordinates to be at bed center.
* Deselect and re-select tool across pause. (Set to standby temp.)
* Set bed standby temps in preheat scripts.
* Add a script for calibrating the mswitch.
* Reduce instantaneous XY drive parameters.
* Increasing pressure advance values for Volcano.
* Full-speed chamber fan on print end.
* Adding another toolhead profile.
* Adding a coarse leveling script for when the gantry is too far out to be corrected by the default dive height.
* Move toolhead thermistor parameters to the heating/toolhead_* scripts, because they change when you swap toolheads.
* README.txt
* README.txt
* Increase idle timeout to 24 hours, and set motors to turn off.
* Set electronics fan min PWM and blip time because my fans are sluggish.
* Extruder drive current adjustments based on PA trials to avoid skipping steps.
* Preheat scripts used the wrong fan control command. And fix some temps.
* Make toolhead heater selection sticky by writing out /sys/restore_tool_heater.g.
* Reduce default PLA print temp.
* Make firmware retraction profile selection sticky by writing out to /sys/restore_retraction.g.
Make separate profiles for V6 and Volcano.
* Filament sensors need to be _turned on_.
* Release notes.
