ff95f859eb
Add support for COMFAST CF-EW72 V2 Hardware: - SoC: Mediatek MT7621 (MT7621DAT or MT7621AT) - Flash: 16 MiB NOR - RAM: 128 MiB - Ethernet: Built-in, 2 x 1GbE - Power: only 802.3af PD on any port, injector supplied in the box - PoE passthrough: No - Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b - Wifi 5GHz: Mediatek MT7613BEN 802.11ac/n/a - LEDs: 8x (only 1 is both visible and controllable, see below) - Buttons: 1x (RESET) Installing OpenWrt: Flashing is done using Mediatek U-Boot System Recovery Mode - make wired connection with 2 cables like this: - - PC (LAN) <-> PoE Injector (LAN) - - PoE Injector (POE) <-> CF-EW72 V2 (LAN). Leave unconnected to CF-EW72 V2 yet. - configure 192.168.1.(2-254)/24 static ip address on your PC LAN - press and keep pressed RESET button on device - power the device by plugging PoE Injector (POE) <-> CF-EW72 V2 (LAN) cable - wait for about 10 seconds until wifi led stops blinking and release RESET button - navigate from your PC to http://192.168.1.1 and upload OpenWrt *-factory.bin firmware file - proceed until router starts blinking with wifi led again (flashing) and stops (rebooting to OpenWrt) MAC addresses as verified by OEM firmware: vendor OpenWrt address LAN lan\eth0 label WAN wan label + 1 2g phy0 label + 2 5g phy1 label + 3 The label MAC address was found in 0xe000. LEDs detailed: The only both visible and controllable indicator is blue:wlan LED. It is not bound by default to indicate activity of any wireless interfaces. Place (WAN->ANT) | Num | GPIO | LED name (LuCI) | Note -----------------|-----|----------------------------------------------------------------------------------------- power | 1 | | | POWER LED. Not controlled with GPIO. hidden_led_2 | 2 | 13 | blue:hidden_led_2 | This LED does not have proper hole in shell. wan | 3 | | | WAN LED. Not controlled with GPIO. hidden_led_4 | 4 | 16 | blue:hidden_led_4 | This LED does not have proper hole in shell. lan | 5 | | | LAN LED. Not controlled with GPIO. noconn_led_6 | 6 | | | Not controlled with GPIO, possibly not connected wlan | 7 | 15 | blue:wlan | WLAN LED. Wireless indicator. noconn_led_8 | 8 | | | Not controlled with GPIO, possibly not connected mt76-phy0 and mt76-phy1 leds also exist in OpenWrt, but do not exist on board. Signed-off-by: Alexey D. Filimonov <alexey@filimonic.net> |
||
|---|---|---|
| .github | ||
| config | ||
| include | ||
| LICENSES | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| COPYING | ||
| feeds.conf.default | ||
| Makefile | ||
| README.md | ||
| rules.mk | ||
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
Development
To build your own firmware you need a GNU/Linux, BSD or MacOSX system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.7+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon oftc.net.
License
OpenWrt is licensed under GPL-2.0