mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-10-19 05:58:53 +02:00
OpenWrt Source Repository
https://openwrt.org/
ee34740ca3
EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band wireless router. Specification SoC: Qualcomm Atheros QCA9558 RAM: 256 MB DDR2 Flash: 16 MB SPI NOR WIFI: 2.4 GHz 3T3R integrated 5 GHz 3T3R QCA9880 Mini PCIe card Ethernet: 5x 10/100/1000 Mbps QCA8337N USB: 1x 2.0 LEDS: 4x GPIO controlled Buttons: 2x GPIO controlled UART: 4 pin header, starting count from white triangle on PCB 1. VCC 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router configuration interface, 3. Go to Tools > Firmware, 4. Select OpenWrt factory image with dlf extension and hit Apply, 5. Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Alternative installation 1. Prepare TFTP server with OpenWrt sysupgrade image, 2. Connect to one of LAN (yellow) ethernet ports, 3. Connect to UART port (leaving out VCC pin!), 4. Power on router, 5. When asked to enter a number 1 or 3 hit 2, this will select flashing image from TFTP server option, 6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8), then router ip (default is 192.168.99.9) and for last, image name downloaded from TFTP server (default is uImageESR1200_1750), 7. After providing all information U-Boot will start flashing the image, You can observe progress on console, it'll take few minutes and when the Power LED will stop blinking, router is ready for configuration. Additional information If connected to UART, when prompted for number on boot, one can enter number 4 to open bootloader (U-Boot) command line. OEM firmware shell password is: aigo3d0a0tdagr useful for creating backup of original firmware. When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep the old configuration. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> |
||
|---|---|---|
| .github | ||
| config | ||
| include | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| feeds.conf.default | ||
| LICENSE | ||
| Makefile | ||
| README | ||
| rules.mk | ||
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org