d03f3dcf3b
Hardware specification ---------------------- * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz * 256MB DRAM * 32MB NOR Flash * 8 x 10/100/1000BASE-T ports * 2 x SFP ports * Power LED, Fault LED * Reset button on front panel * UART (115200 8N1) via populated standard pin header marked JP1 TODO: The SFP ports use a shared SCL GPIO that the driver cannot handle. The left SFP port (lan9) is defined and fully functional while the laser on the right SFP port (lan10) is off by default. UART pinout ----------- [o]ooo|JP1 | ||`------ GND | |`------- RX | `-------- TX `---------- Vcc (3V3) Installation using OEM webinterface ----------------------------------- 1. Make sure you are running OEM firmware in secondary slot 2. Install squashfs-factory.imag to primary slot by upload via http Installation using serial interface ----------------------------------- 1. Press "a" "c" "p" during message "Enter correct key to stop autoboot" 2. Load image with "upgrade runtime <TFTP IP>:squashfs-sysupgrade.bin" command 3. Switch to primary slot with "setsys bootpartition 0" 4. Store config with "savesys" 5. Boot the image with `boota` command Dual-boot with stock firmware using writable u-boot-env ------------------------------------------------------- From stock to OpenWrt / primary image 1 (CLI as admin): - > boot system image1 - > reboot From OpenWrt to stock / boot image 2: (shell as root) - # fw_setsys bootpartition 1 - # reboot Debrick using serial interface ------------------------------ 1. Press "a" "c" "p" during message "Enter correct key to stop autoboot" 2. Load vendor image with "upgrade runtime <TFTP IP>:LGS310xxxxx.imag" 3. switch to primary partition "setsys bootpartition 0" 4. safe config "savesys" Further documentation --------------------- See https://openwrt.org/toh/linksys/lgs352c It has been developed and tested on device with v1 revision. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> Link: https://github.com/openwrt/openwrt/pull/16068 [Add missing 'w' in name of firmware partition] Signed-off-by: Sander Vanheule <sander@svanheule.net> |
||
|---|---|---|
| .devcontainer/ci-env | ||
| .github | ||
| config | ||
| include | ||
| LICENSES | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| COPYING | ||
| feeds.conf.default | ||
| Makefile | ||
| README.md | ||
| rules.mk | ||
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
Development
To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.7+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon oftc.net.
License
OpenWrt is licensed under GPL-2.0