mirror/openwrt
1
0
Fork 0
mirror of https://git.openwrt.org/openwrt/openwrt.git synced 2024-10-19 05:58:53 +02:00
Code Issues
OpenWrt Source Repository https://openwrt.org/
57,367 Commits 8 Branches 72 Tags 240 MiB
C 60.7%
Makefile 19.7%
Shell 7%
Roff 6.8%
Perl 2.6%
Other 3.1%
c9cb6411c1
Go to file
David Bauer c9cb6411c1 mediatek: add support for Cudy WR3000 v1 
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
16MB SPI-NOR (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
      [LEDS] VCC-GND-RX-TX [ETH]
      Header is located below the heatsink

Case
----
Unscrew the 4 bottom screws. Remove the top of the case by inserting a
small screwdriver into the ventilation holes and lift the top cover.

This works best by beginning near the ETH-ports. The top is clipped on
the front near the LEDs with two plastic clips. The back has a single
clip in the middle. Start at one of the back edges.

MAC-Addresses
-------------
80:AF:CA:00:F9:C6 LAN
80:AF:CA:00:F9:C7 WAN
80:AF:CA:00:F9:C6 W2
82:AF:CA:30:F9:C6 W5

Installation
------------

1. Connect to the serial port as described in the "Hardware" section.

2. Power on the device. Keep pressing the "0" key to enter the U-Boot
   shell.

3. Download the OpenWrt initramfs image. Place it on an TFTP server
   connected to the Cudy LAN ports. Make sure the server is reachable at
   192.168.1.2. Rename the image to "cudy3000.bin"

4. Download and boot the OpenWrt initramfs image.

   $ tftpboot 0x46000000 cudy3000.bin; bootm 0x46000000

5. Transfer the OpenWrt sysupgrade image to the device using scp.
   Install with sysupgrade.

Note: Cudy does not yet provide a image for disabling their
signature-protection. This has happened in the past. Make sure to check
the wiki for a possible easier installation method.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-05-18 01:46:13 +02:00
.github ci: use new buildbot worker images with Debian 11 2023-05-15 20:43:47 +02:00
config treewide: cleanup kernel symbol references 2023-05-12 13:02:44 +02:00
include kernel: bump 5.15 to 5.15.111 2023-05-13 22:38:35 +02:00
LICENSES
package iwinfo: update to latest HEAD 2023-05-18 01:44:41 +02:00
scripts Revert "scripts: run ipkg-make-index through shellcheck" 2023-05-09 21:32:26 +02:00
target mediatek: add support for Cudy WR3000 v1 2023-05-18 01:46:13 +02:00
toolchain toolchain/musl: update to 1.2.4 2023-05-15 20:39:17 +02:00
tools tools: squashfs3-lzma: generate reproducible output 2023-05-12 02:27:17 +02:00
.gitattributes
.gitignore
BSDmakefile
Config.in
COPYING
feeds.conf.default
Makefile treewide: derive host and hostpkg path from STAGING_DIR 2023-01-09 21:33:20 +01:00
README.md
rules.mk tools: add gnulib source 2023-05-04 06:07:27 +02:00

README.md

OpenWrt logo

OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.

Sunshine!

Download

Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.

If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.

An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:

Development

To build your own firmware you need a GNU/Linux, BSD or MacOSX system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.

Requirements

You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.

binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.6+ rsync subversion unzip which

Quickstart

  1. Run ./scripts/feeds update -a to obtain all the latest package definitions defined in feeds.conf / feeds.conf.default

  2. Run ./scripts/feeds install -a to install symlinks for all obtained packages into package/feeds/

  3. Run make menuconfig to select your preferred configuration for the toolchain, target system & firmware packages.

  4. Run make to build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.

Related Repositories

The main repository uses multiple sub-repositories to manage packages of different categories. All packages are installed via the OpenWrt package manager called opkg. If you're looking to develop the web interface or port packages to OpenWrt, please find the fitting repository below.

  • LuCI Web Interface: Modern and modular interface to control the device via a web browser.

  • OpenWrt Packages: Community repository of ported packages.

  • OpenWrt Routing: Packages specifically focused on (mesh) routing.

  • OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).

Support Information

For a list of supported devices see the OpenWrt Hardware Database

Documentation

Support Community

  • Forum: For usage, projects, discussions and hardware advise.
  • Support Chat: Channel #openwrt on oftc.net.

Developer Community

License

OpenWrt is licensed under GPL-2.0