c904875562
Hardware: ========= SOC: Qualcomm IPQ4019 WiFi 1: QCA4019 IEEE 802.11b/g/n WiFi 2: QCA4019 IEEE 802.11a/n/ac WiFi 3: QCA9886 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8510 (A10) Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L Ethernet: Qualcomm Atheros QCA8072 (2-port) Flash: Samsung KLM4G1FEPD (4GB eMMC) RAM (NAND): 512MB LED Controller: NXP PCA9633 (I2C) Buttons: Single reset button (GPIO). Ethernet: ========= The device has 2 ethernet ports, configured as follows by default: - left port: WAN - right port: LAN Wifi: ===== The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device. Bluetooth and Zigbee: ===================== Configuration included but not tested. Storage: ======== For compatibility with stock firmware, all of OpenWrt runs in a 136 MiB eMMC partition (of which there are two copies, see below). You can also use partition /dev/mmcblk0p19 "syscfg" (3.4 GiB) any way you see fit. During very limited tests, stock firmware did not mount this partition. However, backing up its stock content before use is recommended anyway. Firmware: ========= The device uses a dual firmware mechanism: it automatically reverts to the previous firmware after 3 failed boot attempts. You can switch to the inactive firmware copy by changing the "boot_part" U-Boot environment variable. You can also do it by turning on the device for a couple of seconds and then back off, 3 times in a row. Installation: ============= OpenWrt's "factory" image can be installed via the stock web UI: 1. Login to the UI. (The default password is printed on the label.) 2. Enter support mode by clicking on the "CA" link at the bottom. 3. Click "Connectivity", "Choose file", "Start", and ignore warnings. This port is based on work done by flipy (https://github.com/flipy). Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> Link: https://github.com/openwrt/openwrt/pull/15345 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|---|---|---|
| .devcontainer/ci-env | ||
| .github | ||
| config | ||
| include | ||
| LICENSES | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| COPYING | ||
| feeds.conf.default | ||
| Makefile | ||
| README.md | ||
| rules.mk | ||
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
Development
To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.7+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon oftc.net.
License
OpenWrt is licensed under GPL-2.0