mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-10-19 14:08:17 +02:00
bbab33724d
Qxwlan E2600AC C1 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB FLASH: 32 MiB Winbond W25Q256 ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power ,6 driven by gpio SERIAL: UART (J5) UUSB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Qxwlan E2600AC C2 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB NOR: 16 MiB Winbond W25Q128 NAND: 128MiB Micron MT29F1G08ABAEAWP ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power, 6 driven by gpio SERIAL: UART (J5) USB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "ubi" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com> [ added rng node. whitespace fixes, ported 02_network, ipq-wifi Makefile, misc dts fixes, trivial message changes ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com> |
||
|---|---|---|
| .. | ||
| 070-v4.20-soc-qcom-spm-add-SCM-probe-dependency.patch | ||
| 071-01-v4.20-ARM-dts-qcom-ipq4019-use-v2-of-the-kpss-bringup-mech.patch | ||
| 071-02-ipq40xx-Fix-booting-secondary-cores.patch | ||
| 072-v4.20-ARM-dts-qcom-ipq4019-add-cpu-operating-points-for-cp.patch | ||
| 073-v4.20-ARM-dts-qcom-ipq4019-fix-cpu0-s-qcom-saw2-reg-value.patch | ||
| 074-ARM-qcom-Add-IPQ4019-SoC-support.patch | ||
| 075-dt-bindings-phy-qcom-ipq4019-usb-add-binding-documen.patch | ||
| 076-phy-qcom-ipq4019-usb-add-driver-for-QCOM-IPQ4019.patch | ||
| 077-qcom-ipq4019-add-USB-devicetree-nodes.patch | ||
| 079-v4.20-ARM-dts-qcom-ipq4019-fix-PCI-range.patch | ||
| 080-ARM-dts-qcom-add-gpio-ranges-property.patch | ||
| 081-clk-fix-apss-cpu-overclocking.patch | ||
| 082-v4.20-mtd-spinand-winbond-Add-support-for-W25N01GV.patch | ||
| 303-spi-nor-enable-4B-opcodes-for-mx25l25635f.patch | ||
| 700-net-add-qualcomm-mdio-and-phy.patch | ||
| 701-dts-ipq4019-add-mdio-node.patch | ||
| 702-dts-ipq4019-add-PHY-switch-nodes.patch | ||
| 703-net-IPQ4019-needs-rfs-vlan_tag-callbacks-in.patch | ||
| 710-net-add-qualcomm-essedma-ethernet-driver.patch | ||
| 711-dts-ipq4019-add-ethernet-essedma-node.patch | ||
| 712-mr33-essedma.patch | ||
| 713-essedma-alloc-skb-ip-align.patch | ||
| 850-soc-add-qualcomm-syscon.patch | ||
| 900-dts-ipq4019-ap-dk01.1.patch | ||
| 901-arm-boot-add-dts-files.patch | ||
| 997-device_tree_cmdline.patch | ||