mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-10-19 05:58:53 +02:00
OpenWrt Source Repository
https://openwrt.org/
9261e7447e
This makes the patches which were just copied in the previous commit apply on top of kernel 4.19. The patches in the backports-4.19 folder were checked if they are really in kernel 4.19 based on the title and only removed if they were found in the upstream kernel. The following additional patches form the pending folder went into upstream Linux 4.19: pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch Bigger changes were introduced to the m25p80 spi nor driver, as far as I saw it in the new code, it now has the functionality provided in this patch: pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch Part of this patch went upstream independent of OpenWrt: hack-4.19/220-gc_sections.patch This patch was reworked to match the changes done upstream. The MIPS DMA API changed a lot, this patch was rewritten to match the new DMA handling: pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch I did bigger manual changes to the following patches and I am not 100% sure if they are all correct: pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch pending-4.19/411-mtd-partial_eraseblock_write.patch pending-4.19/600-netfilter_conntrack_flush.patch pending-4.19/611-netfilter_match_bypass_default_table.patch pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch hack-4.19/211-host_tools_portability.patch hack-4.19/221-module_exports.patch hack-4.19/321-powerpc_crtsavres_prereq.patch hack-4.19/902-debloat_proc.patch This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
|---|---|---|
| .github | ||
| config | ||
| include | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| feeds.conf.default | ||
| LICENSE | ||
| Makefile | ||
| README | ||
| rules.mk | ||
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org