45255aa0e8
Specifications: CPU: MT7621A dual-core 880MHz RAM: 64MB DDR2 FLASH: 16MB MX25L12805D NOR SPI WIFI: 2.4GHz 2x2 MT7603 b/g/n PCI WIFI: 5GHz 2x2 MT7662 a/b/ac PCI ETH: 1xLAN 1000base-T integrated SWITCH: MT7530 Port 0: LAN, Port 6: CPU LED: Power, 2.4GHz WiFi, 5GHz WiFi BTN: WPS, Reset UART: Near ETH port, from ETH: 3V3-TxD-GND-RxD 57600 8n1 MISC: Audio support Installation: 1. Update using recovery mode - while holdig "reset" button, power on the device - keep holding "reset" until power led is flashing yellow - set own IP to 192.168.1.75, subnet mask: 255.255.255.0 - push firmware image (can be factory.bin or sysupgrade.bin) using tftp client in binary mode to 192.168.1.1 Notes: This board has only two MAC addresses programmed in the "factory" partition: - MAC for wlan0 (2.4GHz) at offset 0x0004 - MAC for wlan1 (5GHz) at offset 0x8004 - stock firmware re-uses wlan0 MAC for ethernet - no valid addresses found in 0x28, 0x2e, 0xe000 and 0xe006 Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com> |
||
|---|---|---|
| .github | ||
| config | ||
| include | ||
| LICENSES | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| COPYING | ||
| feeds.conf.default | ||
| Makefile | ||
| README.md | ||
| rules.mk | ||
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Development
To build your own firmware you need a GNU/Linux, BSD or MacOSX system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.6+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon oftc.net.
License
OpenWrt is licensed under GPL-2.0