mirror/openwrt
1
0
Fork 0
mirror of https://git.openwrt.org/openwrt/openwrt.git synced 2024-10-18 13:29:16 +02:00
Code Issues
OpenWrt Source Repository https://openwrt.org/
60,852 Commits 8 Branches 72 Tags 240 MiB
C 60.7%
Makefile 19.7%
Shell 7%
Roff 6.8%
Perl 2.6%
Other 3.1%
2a2f53415e
Go to file
Lea Teuberth 2a2f53415e ramips: add support for TP-Link Archer MR200v5 
Specifications:
	CPU:     MT7628AN 580MHz
	RAM:     64MB DDR2
	FLASH:   8MB EN25QH64 NOR SPI
	WIFI:    2.4GHz 2x2 MT7628 b/g/n internal
	WIFI:    5GHz 1x1 MT7610E ac/n PCI
	LTE:     Qualcomm MDM9207
	ETH:     4xLAN 100base-T integrated
	SWITCH:  RT3050-ESW Port 0,1,2,3: LAN, Port 6: CPU
	LEDS:    LAN, WAN, Power, 3x signal strength, WiFi
	BTNS:    Reset, WiFi toggle
	UART:    Near ETH ports, Vcc-GND-RX-TX, 115200, 8N1

Installation:
	1. Update using recovery mode
        - set your IP to 192.168.0.225, subnet mask: 255.255.255.0
        - start tftp server, rename tftp-recovery.bin to
          tp_recovery.bin and place it into the server's directory
        - while holdig the "reset" button, power on the device
        - keep holding "reset" until the file is being transferred

Notes:
	This board has only one MAC address programmed
        in the "romfile" partition:
        - MAC for phy0 (2.4GHz) at romfile 0xf100 (0)
        - MAC for phy1 (5GHz) at romfile 0xf100 (-1)
        - stock firmware re-uses phy0 MAC for ethernet
        - stock firmware uses romfile 0xf100 (1) for WWAN;
          not used since QMI interface is raw IP

Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
2024-05-23 22:46:26 +02:00
.devcontainer/ci-env
.github
config
include
LICENSES
package build: generate private key for APK early 2024-05-22 19:28:20 +02:00
scripts
target ramips: add support for TP-Link Archer MR200v5 2024-05-23 22:46:26 +02:00
toolchain
tools tools: refresh all patches 2024-05-23 11:49:03 +02:00
.gitattributes
.gitignore
BSDmakefile
Config.in
COPYING
feeds.conf.default
Makefile
README.md
rules.mk

README.md

OpenWrt logo

OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.

Sunshine!

Download

Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.

If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.

An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:

Development

To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.

Requirements

You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.

binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.7+ rsync subversion unzip which

Quickstart

  1. Run ./scripts/feeds update -a to obtain all the latest package definitions defined in feeds.conf / feeds.conf.default

  2. Run ./scripts/feeds install -a to install symlinks for all obtained packages into package/feeds/

  3. Run make menuconfig to select your preferred configuration for the toolchain, target system & firmware packages.

  4. Run make to build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.

Related Repositories

The main repository uses multiple sub-repositories to manage packages of different categories. All packages are installed via the OpenWrt package manager called opkg. If you're looking to develop the web interface or port packages to OpenWrt, please find the fitting repository below.

  • LuCI Web Interface: Modern and modular interface to control the device via a web browser.

  • OpenWrt Packages: Community repository of ported packages.

  • OpenWrt Routing: Packages specifically focused on (mesh) routing.

  • OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).

Support Information

For a list of supported devices see the OpenWrt Hardware Database

Documentation

Support Community

  • Forum: For usage, projects, discussions and hardware advise.
  • Support Chat: Channel #openwrt on oftc.net.

Developer Community

License

OpenWrt is licensed under GPL-2.0