The rss variant should conflict with the default.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16460
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add support for the ArmSoM Sige7 board.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16462
Signed-off-by: Nick Hainke <vincent@systemli.org>
Avoids having to handle EPROBE_DEFER manually.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16456
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix ltssm crashes on BPI-Rx boards.
Seems read32/write32 using wrong address which
is not a problem on x86/64 PCI controllers.
But have issues on BPI-Rx boards.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15945
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allow to build ath11k and other drivers using
qcom-qmi-helpers together (eg. ath12k).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15945
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
1. Remove outdated symbol CONFIG_USB_OHCI_ATH79.
The ath79 OHCI USB was already supported by the generic driver
kmod-usb-ohci. And this kernel symbol has been dropped since
upstream commit:
53d473fc1e38 ("usb: host: Remove the deprecated ATH79 USB host config options")
2. Add ath79 USB phy package to the OHCI dependencies.
Both EHCI and OHCI require it on the ath79 target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add u-boot support based on the kernel dts introduced in d1016446 and
the GL-MT6000 u-boot support in fe10f974.
The pcie-mediatek-gen3 kernel driver doesn't like hotplug, so to work in
PCIe mode, the 5G modem on this device needs to be switched on by u-boot
before starting the kernel. Include an init_modem step in the boot_system
action to set the relevant gpios. (The factory bootloader does the same,
using Mediatek SDK-specific gpio_power_clr and gpio_pull_up.)
Ideally the modem would be started using gpio-hog in the device tree, but
this will need to wait until mediatek gpio-hog support is fixed upstream:
https://lore.kernel.org/u-boot/6ef2583e85eea60560d7776377d662779e7c44e5.1722419839.git.chris@arachsys.com/
The bootloader can be replaced using the built-in web interface of the
factory bootloader. Hold the reset button for five seconds while powering
on the device and it will boot into a recovery http server.
http://192.168.1.1/uboot.html and http://192.168.1.1/bl2.html can then
be used to upload openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip
and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin respectively.
Alternatively, from a root shell on the running system, unlock the boot
partition with
echo 0 >/sys/block/mmcblk0boot0/force_ro
then write openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip to
/dev/mmcblk0p4 and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin
to /dev/mmcblk0boot0.
Signed-off-by: Chris Webb <chris@arachsys.com>
Link: https://github.com/openwrt/openwrt/pull/15645
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ipv6 delegate option is not respected by proto directip
this add support for it.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15508
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This make source based IPv6 routing option available for directip
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15508
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ipv6 delegate option is not respected by proto qmi
this add support for it.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15508
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ipv6 delegate option is not respected by proto ncm
this add support for it.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15508
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ipv6 delegate option is not respected by proto mbim
this add support for it.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15508
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ipv6 delegate option is not respected by proto of ppp/pptp/pppoe/pppoa
this add support for them.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15508
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If the `intval` obtained from `info` is indeed 0, it cannot be set to `conf`.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15495
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The support for assigning PCIe eeprom via device tree was
accidentally removed when adding NVMEM eeprom patches.
Fixes: bea4f5020790 ("mac80211: rt2x00: improve EEPROM load patches")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16318
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Compile LED support to swconfig and phy modules
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building DSA switch drivers as kernel modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building multiple phy drivers as kernel modules
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building both upstream and downstream ag71xx drivers
as modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch add a version to uboot patches to help identify in
futures updates when they were upstreamed.
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
1- The NanoPi R6C is a SBC by FriendlyElec based on the Rockchip RK3588s.
It comes with 4GB or 8GB of RAM, a microSD card slot, optional 32GB eMMC
storage, one M.2 M-Key connector, one RTL8211F 1GbE and one RTL8125
2.5GbE Ethernet port, one USB 2.0 Type-A and one USB 3.0 Type-A port, a
HDMI port, a 30-pin GPIO header as well as multiple buttons and LEDs.
2- Renamed 000-backport-upstream-dts-sync.patch -> 000-v2024.10-rc1-backport-upstream-dts-sync.patch
to add the version when was applied upstream
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Same as 'nohostroute' option for GRE tunnels (commit 0f8b9addfc)
and IPIP tunnels (commit 46ce629fe0)
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15961
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Same as fqdn support in GRE (commit a79f3d11b3) and IPIP (commit 311682905e)
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15961
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
link: https://lore.kernel.org/all/2024091842-CVE-2024-46760-1eb3@gregkh
Description
===========
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: usb: schedule rx work after everything is set up
Right now it's possible to hit NULL pointer dereference in
rtw_rx_fill_rx_status on hw object and/or its fields because
initialization routine can start getting USB replies before
rtw_dev is fully setup.
The stack trace looks like this:
rtw_rx_fill_rx_status
rtw8821c_query_rx_desc
rtw_usb_rx_handler
...
queue_work
rtw_usb_read_port_complete
...
usb_submit_urb
rtw_usb_rx_resubmit
rtw_usb_init_rx
rtw_usb_probe
So while we do the async stuff rtw_usb_probe continues and calls
rtw_register_hw, which does all kinds of initialization (e.g.
via ieee80211_register_hw) that rtw_rx_fill_rx_status relies on.
Fix this by moving the first usb_submit_urb after everything
is set up.
For me, this bug manifested as:
[ 8.893177] rtw_8821cu 1-1:1.2: band wrong, packet dropped
[ 8.910904] rtw_8821cu 1-1:1.2: hw->conf.chandef.chan NULL in rtw_rx_fill_rx_status
because I'm using Larry's backport of rtw88 driver with the NULL
checks in rtw_rx_fill_rx_status.
The Linux kernel CVE team has assigned CVE-2024-46760 to this issue.
Affected and fixed versions
===========================
Fixed in 6.6.51 with commit c83d464b82a8
Fixed in 6.10.10 with commit 25eaef533bf3
Fixed in 6.11 with commit adc539784c98
Please see https://www.kernel.org for a full list of currently supported
kernel versions by the kernel community.
Unaffected versions might change over time as fixes are backported to
older supported kernel versions. The official CVE entry at
https://cve.org/CVERecord/?id=CVE-2024-46760
will be updated if fixes are backported, please check that for the most
up to date information about this issue.
Affected files
==============
The file(s) affected by this issue are:
drivers/net/wireless/realtek/rtw88/usb.c
Mitigation
==========
The Linux kernel CVE team recommends that you update to the latest
stable kernel version for this, and many other bugfixes. Individual
changes are never tested alone, but rather are part of a larger kernel
release. Cherry-picking individual commits is not recommended or
supported by the Linux kernel community at all. If however, updating to
the latest release is impossible, the individual changes to resolve this
issue can be found at these commits:
https://git.kernel.org/stable/c/c83d464b82a8ad62ec9077637f75d73fe955635ahttps://git.kernel.org/stable/c/25eaef533bf3ccc6fee5067aac16f41f280e343ehttps://git.kernel.org/stable/c/adc539784c98a7cc602cbf557debfc2e7b9be8b3
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16420
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification is similar to other devices of the MT Stuart series:
* Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 2 GiB DDR4 RAM
* 2500M/1000M/100M LAN port
* 10000M/5000M/2500M/1000M/100M/10M WAN port
* MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
* Renesas DA14531MOD Bluetooth
* 2 buttons (Reset, Mesh/WPS)
* uC-controlled RGB LED via I2C
* 2x LED for the 2.5G port, 3x LED for the 10G port
* 3.3V-level 115200 baud UART console via 4-pin Dupont connector
exposed at the bottom of the device
* USB-C PD power input
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
