Drop obsolete control interface patches.
This fixes some corner cases in the previous code where the segment 0 center
frequency was not adjusted properly, leading to logspam and non-working AP
interfaces.
Additionally, shutting down the AP was broken, because the next beacon update
would re-enable it, leading to a race condition on assoc.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes this error: hostapd: nl80211: kernel reports: integer out of range
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Check the phy before removing unrelated netdevs on the same hw device
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When building xdp-tools with CONFIG_USE_LLVM_HOST=y, on a host that
enabled stack protector by default in Clang, compilation fails with the
following error:
CLANG xdp-dispatcher.o
clang-16: error: ignoring '-fstack-protector-strong' option as it is not currently supported for target 'bpfeb' [-Werror,-Woption-ignored]
Add -fno-stack-protector to BPF_CFLAGS to fix this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Include AP ucode source file
Fixes: e56c5f7b276a ("hostapd: add ucode support, use ucode for the main ubus object")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
8c2758b4fbbb wireless: add support for replacing data blobs at runtime
0ff22a6a68ce wireless: enable dynamic reconfiguration by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This implements vastly improved dynamic configuration reload support.
It can handle configuration changes on individual wifi interfaces, as well
as adding/removing interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used to run a standalone EAP server that can be used from
other APs. It uses json as user database format and can automatically
handle reload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
At least Fedora and RHEL 9 set RSAMinSize=2048, so when trying to use
failsafe, we get 'Bad server host key: Invalid key length'
To workaround the issue, we can use: ssh -o RSAMinSize=1024 ...
Generating 2048 bits RSA is extremely slow, so add ed25519.
We keep RSA 1024 to be as compatible as possible.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
ChangeLog:
125b080 Release version 6.4.
5660918 update UAPI header copies
f493e63 netlink: fix duplex setting
b3e341c cmis: report LOL / LOS / Tx Fault
045d8db sff-8636: report LOL / LOS / Tx Fault
a6505f3 drop checks for macros provided in UAPI header copies
86c0c41 do not check for strtol() function
dd8e3ae actually check for C11 compiler
43e4d30 add local copies of macros from autoconf-archive
faa4700 drop check for big endian types
31b7b5e Require a compiler with support for C11 features
946d18b update UAPI header copies
eebf01f ethtool: Add support for configuring tx-push-buf-len
2782ea8 update UAPI header copies
Signed-off-by: Nick Hainke <vincent@systemli.org>
d1f07cf devices: add device id for Atheros AR9287 and AR9380
65ea345 nl80211: constify a few arrays
ca79f64 lib: report byte counters as 64 bit values
This contains an ABI change, increase the ABI version too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
493e1589bc8b bridge: fix coverity false positive report
03a619947717 bridge: add support for configuring extra vlans for the bridge itself
4bea6d21a9ab wireless: fix changing reconf/serialize options in configuration
255b4d5c472e wireless: fix handling config reload with reconf=1
1ab992a74b43 wireless: fix another reconf issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
5211264 odhcpd: add support for dhcpv6_pd_min_len parameter
c6bff6f router: Add PREF64 (RFC 8781) support
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
1571e18e4a69 bridge: add support for configuring extra tagged vlans on member devices
b719f189f243 bridge: make hotplug-added vlans default to tagged
edf3aced9f9a bridge: add support for adding vlan ranges via hotplug
Signed-off-by: Felix Fietkau <nbd@nbd.name>
077e05f2b129 vlan/vlandev: pass through extra vlan information passed via hotplug
40fad91eb5be wireless: add network_vlan config attribute
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add an UCI option to enable Multiple BSSID Advertisement. Enabling this
will announce all BSSIDS on a phy in a single beacon frame. The
interface that is brought up first will be the transmitting profile, all
others are non-transmitting profiles and will be advertised in the
Multiple BSSID element in Beacon and Probe Response frames of the first
interface.
This depends on driver and client support. Enabling this will result in
all but the first interface not being visible at all for clients that do
not support it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Backport patches improving ppp interface creation. As a side effect this
also fix a bug from using netdev trigger that suffer from LED state
wrongly set due to using old ioctl for ppp creation.
Tested-by: Csaba Sipos <metro4@freemail.hu>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the repository
link to the new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
If dual-stack configuration is in use, and dhcpv6 option is set, do not start
464xlat sub-interface for dhcpv6 sub-interace , as the configuration already
provides IPv4 connectivty, be it through single or dual APN configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add two new "v6apn" and "v6profile" properties, to support split-APN
dual-stack onfiguration. This extends the existing ipv4v6 PDP type,
allowing simultaneous connection to two distinct APNs,
one for IPv4 and one for IPv6.
The parameters override existing 'apn' and 'profile' respectively,
if set, but only for IPv6 part of the connection.
If unset, they default to their original values, constituting a standard
IPv4v6 setup.
If a different APN is set for IPv6, a corresponding profile MUST also be
configured, with a different ID, than the IPv4 profile, for example,
profile 2.
Both APNs must match ones configured through QMI or through 'AT+CGDCONT'
command.
Example configuration in UCI:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option autoconnect '1'
option pdptype 'ipv4v6'
option apn 'internet'
option v6apn 'internetipv6'
option profile '1'
option v6profile '2'
Corresponding profile configuration:
AT+CGDCONT?
+CGDCONT: 1,"IP","internet","0.0.0.0",0,0,0,0
+CGDCONT: 2,"IPV6","internetipv6","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The cli is a one-time run, and memory leaks would have been irrelevant. But people call libsw with cli programs as samples.
Doing a good job of memory management calls means that people who call libsw are not so easy to make mistakes.
Signed-off-by: nichel Chen <nichelnich@gmail.com>
412d03012f13 network: prevent adding endpoint routes for addresses on the network
faaf9cee6ef4 utils: fix ipv4 checksum issue
0e1c2fad3540 pex-msg: fix memory leak on fread fail in pex_msg_update_request_init
51be0ed659d0 host: fix crash parsing gateway when no endpoint is specified
ca17601dc24e wg-linux: add support for splitting netlink messages for allowed ips
7d3986b7a5a2 wg-linux: increase default messages size
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix the PKG_MIRROR_HASH value for netifd.
Fixes: d2ecaaca3404 ("netifd: update to version 2023-05-31")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Contains following changes:
* bridge: bridge_dump_info: add dumping of bridge attributes
* bridge: make it more clear why the config was applied
* cmake: fix build by reordering the cflags definitions
* treewide: fix multiple compiler warnings
Signed-off-by: Petr Štetiar <ynezz@true.cz>
My original bpftools package made "variant" builds of bpftool and libbpf
as a convenience, since both used the same local kernel sources with the
same versioning. This is no longer the case, since the commit below
switched to using an out-of-tree build mirror hosting repos for each.
Replace bpftools with separate bpftool and libbpf packages, each simplified
and correctly versioned. Also fix the broken libbpf ABI introduced in the
same commit. Existing build .config files are not impacted.
Fixes: 00cbf6f6ab1d ("bpftools: update to standalone bpftools + libbpf, use the latest version")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
adds ForceCommand option. If the command is specified,
it forces users to execute the command when they log in.
Signed-off-by: Nozomi Miyamori <inspc43313@yahoo.co.jp>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Update to umdns HEAD to include latest enhancements for browse method
filtering, return of TXT records as an array, dumping IPv4/6 as an
array, and including the interface name in a browse reply.
Signed-off-by: Mark Baker <mark@vpost.net>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x, mt7621, x86_64
TOZED TL70-C is an LTE CAT6 cellular modem based on UNISOC SL8563. UNISOC
was formerly called Spreadtrum hence the manufacturer name detected on the
modem is spreadtrum.
The connect and disconnect commands bring up and down the usb0 interface.
They are Base64 encoded as that's what the AT command accepts. The modem
can do up to 4 APNs by bringing the USB interfaces, usb0 to usb3, up.
Setting the USB interfaces up:
connmanctl ndisdial AT^NDISDUN="usb0",1,1
connmanctl ndisdial AT^NDISDUN="usb1",1,2
connmanctl ndisdial AT^NDISDUN="usb2",1,3
connmanctl ndisdial AT^NDISDUN="usb3",1,4
Setting the USB interfaces down:
connmanctl ndisdial AT^NDISDUN="usb0",0,1
connmanctl ndisdial AT^NDISDUN="usb1",0,2
connmanctl ndisdial AT^NDISDUN="usb2",0,3
connmanctl ndisdial AT^NDISDUN="usb3",0,4
Co-developed-by: Andre Cruz <me@1conan.com>
Signed-off-by: Andre Cruz <me@1conan.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
add description for medion usb lte webstick
Signed-off-by: Joe Cooper <highjagger+github@gmail.com>
[bump PKG_RELEASE]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Based on Paul Fertser <fercerpav@gmail.com>'s guidance:
Change AUTORELEASE in rules.mk to:
```
AUTORELEASE = $(if $(DUMP),0,$(shell sed -i "s/\$$(AUTORELEASE)/$(call commitcount,1)/" $(CURDIR)/Makefile))
```
then update all affected packages by:
```
for i in $(git grep -l PKG_RELEASE:=.*AUTORELEASE | sed 's^.*/\([^/]*\)/Makefile^\1^';);
do
make package/$i/clean
done
```
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
