For many target we have added CONFIG_WATCHDOG_CORE=y to the target
config due to the following error:
Package kmod-hwmon-sch5627 is missing dependencies for the following
libraries:
watchdog.ko
However, actually the proper way appears to be setting the
dependency for the kmod-hwmon-sch5627 package, as the error message
demands.
Do this in this patch and remove the target config entries added
due to this issue.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds a `selinux` variant which comes with with a number of
SELinux applets and also SELinux label support.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Fixes package libcurl build issue :
Package libcurl is missing dependencies for the following libraries:
libzstd.so.1
Suggested-by: Syrone Wong <wong.syrone@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
8027c7d95274 mt76: mt7615: fix reading airtime statistics
3743e7c904de mt76: mt7915: optimize mt7915_mac_sta_poll
d2fe5e8330c6 mt76: mt7915: fix variable initialization in sta poll
692065b4c9db mt76: mt7915: only enable hw amsdu for AP and station
b54157df7c27 mt7615: update firmware to version 20200814
888990e159d2 mt76: use threaded NAPI
3a3306e408f2 mt76: mt7915: add 802.11 encap offload support
795b772cd392 mt76: mt7915: add encap offload for 4-address mode stations
55d79ab7fa23 mt76: dma: update q->queued immediately on cleanup
23dbd64d6324 mt76: mt7915: schedule tx tasklet in mt7915_mac_tx_free
5cf34cda70af mt76: mt7915: significantly reduce interrupt load
87a69429069f mt76: add utility functions for deferring work to a kernel thread
2f1318a06d0a mt76: convert from tx tasklet to tx worker thread
72f0979566be mt76: mt7915: add support for accessing mapped registers via bus ops
f9ce5c776c9a mt76: use ieee80211_rx_list to pass frames to the network stack as a batch
25dd8bdae3bf mt76: mt7615: significantly reduce interrupt load
7c5445dec812 mt76: mt7615: release mutex in mt7615_reset_test_set
e68c3e254822 mt76: mt7663s: use NULL instead of 0 in sdio code
4368380e20e7 mt76: mt7663s: fix resume failure
bea386f27914 mt76: mt7663s: fix unable to handle kernel paging request
b8780c44c716 mt76: mt7615: fix possible memory leak in mt7615_tm_set_tx_power
37a1c7ed6796 mt76: mt7615: fix a possible NULL pointer dereference in mt7615_pm_wake_work
8c7c1a207d25 mt76: fix a possible NULL pointer dereference in mt76_testmode_dump
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Abort the dhcp-check based on the interface instead of the carrier
state. In cases where the interface is up but the carrier is down,
netifd won't cause a dnsmasq reload, thus dhcp won't become active
on this interface.
Signed-off-by: David Bauer <mail@david-bauer.net>
"type" is already used as a common option for all protocols types, so
using the same option name for the map type makes the configuration
ambiguous. Luci in particular adds controls for both options and sees
errors when reading the resulting configuration.
Use "maptype" instead, but still fallback to "type" if "maptype" is not
set. This allows configurations to migrate without breaking old
configurations.
This addresses FS#3287.
Signed-off-by: Remi NGUYEN VAN <remi.nguyenvan+openwrt@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
The is no reason to catch the output by $() and then echo it again.
Remove the useless echos.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The legacy map version based on the IPv6 Interface Identifier in
draft-ietf-softwire-map-03 was typically used by uncommenting the LEGACY
variable in the map.sh file, which is not ideal. A proper configuration
option is needed instead.
The IPv6 Interface Identifier format described in the draft was
eventually changed in RFC7597, but is still used by some major ISPs,
including in Japan.
Signed-off-by: Remi NGUYEN VAN <remi.nguyenvan+openwrt@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
If not needed, disabling scp allows for a nice size reduction.
Dropbear executable size comparison:
153621 bytes (baseline)
133077 bytes (without scp)
In other words, we trim a total of 20544 bytes.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
ALLNET ALL-WAP02860AC is a dual-band wireless access point.
Specification
SoC: Qualcomm Atheros QCA9558
RAM: 128 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 1x 10/100/1000 Mbps AR8035-A, PoE capable (802.3at)
LEDS: 5x, which four are GPIO controlled
Buttons: 1x GPIO controlled
UART: 4 pin header near Mini PCIe card, starting count from white
triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
MAC addresses
Calibration data does not contain valid MAC addresses.
The calculated MAC addresses are chosen in accordance with OEM firmware.
Because of:
a) constrained environment (SNMP) when connecting through Telnet
or SSH,
b) hard-coded kernel and rootfs sizes,
c) checksum verification of kerenel and rootfs images in bootloder,
creating factory image accepted by OEM web interface is difficult,
therefore, to install OpenWrt on this device UART connection is needed.
The teardown is simple, unscrew four screws to disassemble the casing,
plus two screws to separate mainboard from the casing.
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
Installation
1. Prepare TFTP server with OpenWrt initramfs-kernel image.
2. Connect to LAN port.
3. Connect to UART port.
4. Power on the device and when prompted to stop autoboot, hit any key.
5. Alter U-Boot environment with following commands:
setenv failsafe_boot bootm 0x9f0a0000
saveenv
6. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
'setenv' to do that, then run following commands:
tftpboot 0x81000000 <openwrt_initramfs-kernel_image_name>
bootm 0x81000000
7. Wait about 1 minute for OpenWrt to boot.
8. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n /tmp/<openwrt_sysupgrade_image_name>
9. After flashing, the access point will reboot to OpenWrt. Wait few
minutes, until the Power LED stops blinking, then it's ready for
configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[add MAC address comment to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The most recent patch added add lines in one block instead of in the
appropriate places to keep Makefiles in consistent style. Fix that.
Fixes: ff02e1561f ("pcre: add host variant of libpcre")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
34aed01ca865 mt76: mt7915: use ieee80211_free_txskb to free tx skbs
efc8669db5f9 mt76: mt7915: fix max_mpdu_size field for A-MSDU
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Dependencies are meant to express actual run-time dependencies and
strictly speaking, libselinux can be build and used on kernels without
SELinux (not in a very meaningful way, but never mind).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit adds a `selinux` variant to `procd` allowing to load an
SELinux policy at boot.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This driver is only used by ipq806x SoCs. Move it there and drop
dependency from ipq40xx since it's not used anywere.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase on changes to previous patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
- Replace dwc3 phy patch with upstream version
- Rework the dts to use the upstream bindings
- Update changed config flags
- Rename module to reflect config name
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
The ssh symlink was still being created even when dbclient was disabled in the
build configuration. Fix this annoyance.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
8d9a62e4def7 mt76: mt7915: fix crash on tx rate report for invalid stations
825343467df4 mt76: fix double DMA unmap of the first buffer on 7615/7915
99804560372b mt76: mt7615: register ext_phy if DBDC is detected
93407be934b2 mt76: mt7615: move drv_own/fw_own in mt7615_mcu_ops
e7774de844e8 mt76: mt7663s: move drv_own/fw_own in mt7615_mcu_ops
a5602514ab03 mt76: mt7615: hold mt76 lock queueing wd in mt7615_queue_key_update
5c42061ce181 mt76: do not inject packets if MT76_STATE_PM is set
ae4757a0ae90 mt76: mt7615: reschedule runtime-pm receiving a tx interrupt
c4544d1e8a1a mt76: mt76s: fix oom in mt76s_tx_queue_skb_raw
dc73103874cc mt76: mt76s: move tx processing in a dedicated wq
c828c84cb134 mt76: mt7663s: move rx processing in txrx wq
2b34f2f6b0ef mt76: mt76s: move status processing in txrx wq
f957b050d848 mt76: mt76s: move tx/rx processing in 2 separate works
6fe964295bd9 mt76: mt76s: get rid of unused variable
43d6127d8851 mt76: mt7915: enable U-APSD on AP side
58774b605f1c mt76: set interrupt mask register to 0 before requesting irq
06f722d8046c mt76: mt7915: clean up and fix interrupt masking in the irq handler
2fbd6baac103 mt76: mt7615: only clear unmasked interrupts in irq tasklet
5ea8b6187da2 mt76: mt76x02: clean up and fix interrupt masking in the irq handler
f2e71f0c1b7e mt76: mt7615: do not do any work in napi poll after calling napi_complete_done()
1eb94624bb12 mt76: mt7915: do not do any work in napi poll after calling napi_complete_done()
5e0c587b9ac1 mt76: mt7915: clean up station stats polling and rate control update
9ab20dfbf7b1 mt76: mt7915: increase tx retry count
fa69dd96f9c0 mt76: mt7915: enable offloading of sequence number assignment
9816f9812adb mt76: move mt76_check_agg_ssn to driver tx_prepare calls
ad90170b0af9 mt76: mt7615: remove mtxq->agg_ssn assignment
335cd51be4c6 mt76: mt7915: simplify aggregation session check
21f7734cbb49 mt76: mt7915: add missing flags in WMM parameter settings
21182f90d947 mt76: mt7915: add Tx A-MSDU offloading support
27670514328f mt76: mt7615: use v1 MCU API on MT7615 to fix issues with adding/removing stations
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Not a large change from last time, but should fix at least one rare wave-2
crash. The htt-mgt-community builds are trimmed for supporting lots of
stations (typically 150+ stations per radio).
Tested on Netgear R7800.
Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Bump PKG_RELEASE for the affected packages as replacing "which" by
"command -v" represents a content change.
Fixes: 1fdf6b745cc3 ("treewide: replace `which` with `command -v`")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix shellcheck SC2230
> which is non-standard. Use builtin 'command -v' instead.
Using `command -v` is POSIX compliant while `which` is not. Also to
mention, `command -v` is a shell builtin whereas `which` is a separate
busybox applet.
Once applied to everything concerning OpenWrt we can disable the busybox
feature `which` and save 3.8kB.
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Paul Spooren <mail@aparcar.org>
[also replace cases in zram-swap]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This problem has been fixed in upstream commit
6b6a3d9339f1c08efaa18a7fb7357e20b48bdc95. This patch now (harmlessly)
adds the same definition a second time.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
[bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Now that my patches have been merged into upstream U-Boot, resync the
cosmetic changes and the commit IDs from the final commits.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The pkgconfig file references the host directories, not the openwrt
ones. Used SED to fix as is done elsewhere. Removed CMAKE_INSTALL as a
result.
Removed now pointless CFLAGS.
Added PKG_BUILD_PARALLEL for faster compilation.
Various rearrangements for consistency between packages.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
677aa53 Fix -W option for pppoe-discovery utility (#157)
115c419 Accept Malformed Windows Success Message (#156)
5bdb148 pppd: Add documentation of stop-bits option to pppd man page (#154)
2a7981f Add ipv6cp-accept-remote option
0678d3b pppd: Fix the default value for ipv6cp-accept-local to false
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
readelf is linked against this library on MIPS64BE
This fixes a build problem on MIPS64BE.
In addition also explicitly activate it in the configure command.
Fixes: 60f595daab45 ("binutils: update to version 2.34")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A bunch of kernel modules depends on kmod-usb-net, but does not
select it. Make AddDepends/usb-net selective, so we can drop
some redundant +kmod-usb-net definitions for DEVICE_PACKAGES.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds a patch to procd to support loading the SELinux
policy early at boot time, and adjusts the procd package to use this
SELinux support when libselinux is enabled.
The procd patch has been submitted separately [1]: obviously the
intent is to have it merged in the procd Git repository rather than
have it in OpenWrt itself.
[1] http://lists.infradead.org/pipermail/openwrt-devel/2019-November/025791.html
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[rebase, add commit message]
Signed-off-by: W. Michael Petullo <mike@flyn.org>
[split commit into openwrt.git and procd.git]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds support for ZyXEL NBG6616 uboot-env access
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[add "ar71xx" to commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
mac80211 reports a packet loss event to user space when 50 consecutive packets
were not acked. On a high throughput link with long aggregates and sudden
link changes, this can trigger way too easily.
Mitigate false positives by only triggering the event on a packet loss if
no ACK was received for at least a second
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Exchange the patch fixing the kernel ringbuffer WARNING flood for the
one accepted upstream.
Fixes commit a956c14d6aa4 ("mac80211: util: don't warn on missing sband
iftype data")
Signed-off-by: David Bauer <mail@david-bauer.net>
The hostapd configuration logic is supposed to accept "option key" as
legacy alias for "option auth_secret". This particular fallback option
failed to work though because "key" was not a registered configuration
variable.
Fix this issue by registering the "key" option as well, similar to the
existing "server" nad "port" options.
Ref: https://github.com/openwrt/openwrt/pull/3282
Suggested-by: Michael Jones <mike@meshplusplus.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
If an existing "wpa_psk_file" is passed to hostapd, the "key" option may
be omitted.
While we're at it, also improve the passphrase length checking to ensure
that it is either exactly 64 bytes or 8 to 63 bytes.
Fixes: FS#2689
Ref: https://github.com/openwrt/openwrt/pull/3283
Suggested-by: Michael Jones <mike@meshplusplus.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add a dependency on kmod-nls-base for the new exfat driver. Otherwise
the build fails on ramips and ath79 on kernel 5.4:
Package kmod-fs-exfat is missing dependencies for the following libraries:
nls_base.ko
Fixes commit cd41234d2f63 ("exfat: add out of tree module")
Signed-off-by: David Bauer <mail@david-bauer.net>
The board name is equivalent to the compatible, not the device
definition. Fix it.
Fixes: b4588c853838 ("kernel/om-watchdog: Apply device renames from ramips")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add package which provides size optimized wpad with support for just
WPA-PSK, SAE (WPA3-Personal), 802.11r and 802.11w.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[adapt to recent changes, add dependency for WPA_WOLFSSL config]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When passing a section or option value to config_get() which contains
characters that happen to be valid variable interpolation expressions,
the function returns a nonsensical expression result instead of the
expected empty string.
When the passed section or option name contains other characters which
are not valid within a shell variable name, a substitution error is
occuring instead.
The issue can be easily reproduced by one of the following examples:
root@OpenWrt:~# . /lib/functions.sh
root@OpenWrt:~# config load system
root@OpenWrt:~# config_get variable invalid-section option
root@OpenWrt:~# echo "$variable"
section_option:-
root@OpenWrt:~# . /lib/functions.sh
root@OpenWrt:~# config load system
root@OpenWrt:~# config_get variable section invalid-option
root@OpenWrt:~# echo "$variable"
option:-
root@OpenWrt:~# . /lib/functions.sh
root@OpenWrt:~# config load system
root@OpenWrt:~# config_get variable section invalid@option
-ash: eval: syntax error: bad substitution
Fix this issue by only performing interpolations when the given section
and option arguments are free of illegal characters.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Before this commit, if uci option "dnssec" was set, we pass "--dnssec"
and friends to dnsmasq, let it start and decide whether to quit and
whether to emit message for diagnosis
# dnsmasq --dnssec; echo $?
dnsmasq: DNSSEC not available: set HAVE_DNSSEC in src/config.h
1
DNSSEC as a feature is different from others like dhcp, tftp in that
it's a security feature. Better be explicit. With this change
committed, we make it so by not allowing it in the first in the
initscript, should dnsmasq later decides to not quit (not likely) or
quit without above explicit error (unlikely but less so ;)
So this is just being proactive. on/off choices with uci option
"dnssec" are still available like before
Link: https://github.com/openwrt/openwrt/pull/3265#issuecomment-667795302
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
47a9f0d service: add method to query available container features
afbaba9 initd: attempt to mount cgroup2
ead60fe jail: use pidns semantics also for timens
759e9f8 jail: make use of BLOBMSG_CAST_INT64 for OCI rlimits
83053b6 instance: add instances into unified cgroup hierarchy
16159bb jail: parse OCI cgroups resources
282ff0c jail: only free cgroups if they were allocated
ab55357 jail: fix freeing cgroups avl
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch adds support for the WNDR4300TN, marketed by Belgian ISP
Telenet. The hardware is the same as the WNDR4300 v1, without the
fifth ethernet port (WAN) and the USB port. The circuit board has
the traces, but the components are missing.
Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2.4 GHz)
* Ethernet: 4x 1000Base-T
* LED: Power, LAN, WiFi 2.4GHz, WiFi 5GHz, WPS
* UART: on board, to the right of the RF shield at the top of the board
Installation:
* Flashing through the OEM web interface:
+ Connect your computer to the router with an ethernet cable and browse
to http://192.168.0.51/
+ Log in with the default credentials are admin:password
+ Browse to Advanced > Administration > Firmware Upgrade in the Telenet
interface
+ Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
+ Proceed with the firmware installation and give the device a few
minutes to finish and reboot.
* Flashing through TFTP:
+ Configure your wired client with a static IP in the 192.168.1.x range,
e.g. 192.168.1.10 and netmask 255.255.255.0.
+ Power off the router.
+ Press and hold the RESET button (the factory reset button on the bottom
of the device, with the gray circle around it, next to the Telenet logo)
and turn the router on while keeping the button pressed.
+ The power LED will start flashing orange. You can release the button
once it switches to flashing green.
+ Transfer the image over TFTP:
$ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
Signed-off-by: Davy Hollevoet <github@natox.be>
[use DT label reference for adding LEDs in DTSI files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
47a9f0d service: add method to query available container features
afbaba9 initd: attempt to mount cgroup2
ead60fe jail: use pidns semantics also for timens
759e9f8 jail: make use of BLOBMSG_CAST_INT64 for OCI rlimits
83053b6 instance: add instances into unified cgroup hierarchy
16159bb jail: parse OCI cgroups resources
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Testmode commands are typically only used for manufacturing or vendor specific
debugging features, so they should not be in the default image
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With the introduction of the generic OpenVPN hotplug mechanism, wrapped
--up and --down scripts got the wrong amount and order of arguments passed,
breaking existing configurations and functionality.
Fix this issue by passing the same amount of arguments in the same expected
order as if the scripts were executed by the OpenVPN daemon directly.
Ref: https://github.com/openwrt/openwrt/pull/1596#issuecomment-668935156
Fixes: 8fe9940db6 ("openvpn: add generic hotplug mechanism")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This package provides the necessary files to translate `config dsa_vlan`
and `config dsa_port` sections of `/etc/config/network` into appropriate
bridge vlan filter rules.
The approach of the configuration is to bridge all DSA ports into a logical
bridge device, called "switch0" by default, and to set VLAN port membership,
tagging state and PVID as specified by UCI on each port and on the switch
bridge device itself, allowing logical interfaces to reference port VLAN
groups by using "switch0.N" as ifname, where N denotes the VLAN ID.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
212f836 ubus: rename JSON-RPC format related functions
628341f ubus: use local "blob_buf" in uh_ubus_handle_request_object()
9d663e7 ubus: use BLOBMSG_TYPE_UNSPEC for "params" JSON attribute
77d345e ubus: drop unused "obj" arguments
8d9e1fc ubus: parse "call" method params only for relevant call
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* compat: rhel 8.3 beta removed nf_nat_core.h
* compat: ipv6_dst_lookup_flow was ported to rhel 7.9 beta
This compat tag adds support for RHEL 8.3 beta and RHEL 7.9 beta, in addition
to RHEL 8.2 and RHEL 7.8. It also marks the first time that
<https://www.wireguard.com/build-status/> is all green for all RHEL kernels.
After quite a bit of trickery, we've finally got the RHEL kernels building
automatically.
* compat: allow override of depmod basedir
When building in an environment with a different modules install path, it's
not possible to override the depmod basedir flag by setting the DEPMODBASEDIR
environment variable.
* compat: add missing headers for ip_tunnel_parse_protocol
This fixes compilation with some unusual configurations.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
ifconfig is effectively deprecated for quite some time now. Let's
replace the remaining occurrences for packages by the
corresponding ip commands now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update the openvpn sample configurations to use modern options in favor
of deprecated ones, suggest more sane default settings and add some
warnings.
* Add tls_crypt and ncp_disable to the sample configuration
* Replace nsCertType with remote_cert_tls in client sample configuration
* Comment out "option compress", compression should not be preferred
* Advise 2048-bit Diffie-Hellman parameters by default
* Add warnings about compression and use of Blowfish (BF-CBC)
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
The wg utility compiles and runs without issues in MIPS16 mode, despite setting
PKG_USE_MIPS16:=0 in the makefile. Let's remove this, allowing for a substantial
size reduction of the wg executable. Since wg is a just a configuration utility,
it shouldn't be performance-critical, as the crypto heavy-lifting is done on the
kernel side.
wg sizes for both modes:
MIPS32: 64309 bytes
MIPS16: 42501 bytes
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
>From an email conversation with the person responsible for upstreaming
the exFAT driver, it seems the staging one in kernel 5.4 is not so
good. Excerpts below.
Namjae Jeon:
Hm... exfat in 5.4 kernel that we did crap shit long time ago is
contributed by someone who we don't know.
This version is unstable and low quality code. We have been improving
it continuously.
and staging version exfat is removed from linux 5.7 kernel.
linux exfat oot version is a backport of exfat in linux 5.7 kernel to
support lower version kernel, and it is a real.
You can see the patch history fro linux-exfat-oot.
this version support timezone and boot sector verification feature newly.
and better filesystem structure and much clean code quality that
reviewed by high profile kernel developers. and add many bug fixes.
And this version is officially maintained by me and kernel guys.
I would not recommend to use staging exfat version.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Don't kill the wireless daemon on teardown. hostapd as well as
wpa_supplicant are managed by procd which would detect the shutdown of
either process as a crash loop.
Signed-off-by: David Bauer <mail@david-bauer.net>
When retrieving the PID for hostapd and wpa_supplicant via ubus the
wrong service name is currently used. This leads to the following error
in the log:
netifd: radio0 (1409): WARNING (wireless_add_process):
executable path /usr/sbin/wpad does not match process path (/proc/exe)
Fixing the service name retrieves the correct PID and therefore the
warning won't occur.
Signed-off-by: David Bauer <mail@david-bauer.net>
This replaces the internal device names "Audi" and "Viper" with the
real model names, which a user would look for. This makes the
Linksys devices on this target consistent with the names recently
changed for mvebu based on the same idea.
As a consequence, the "viper" device definition is split into two
separate definitions with the correct names for both real models.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Explicitly mount the BPF filesystem if available. This is used for pinning
eBPF programs and maps, making them accessible to other eBPF programs or
from userspace with the help of libbpf or bpftool.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
[daniel@makrotopia.org: bumped PKG_RELEASE]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The current selection of DRIVER_MAKEOPTS and TARGET_LDFLAGS is
exceptionally hard to read. This tries to make things a little
easier by inverting the hierarchy of the conditions, so SSL_VARIANT
is checked first and LOCAL_VARIANT is checked second.
This exploits the fact that some of the previous conditions were
unnecessary, e.g. there is no hostapd-mesh*, so we don't need
to exclude this combination.
It also should make it a little easier to see which options are
actually switched by SSL_VARIANT and which by LOCAL_VARIANT.
The patch is supposed to be cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, the compatibility mechanism only works if both device and
image are already updated to the new routines. This patch extends
the sysupgrade metadata and fwtool_check_image() to account for
"older" images as well:
The basic mechanism for older devices to check for image compatibility
is the supported_devices entry. This can be exploited by putting
a custom message into this variable of the metadata, so older FW
will produce a mismatch and print the message as it thinks it's the
list of supported devices. So, we have two cases:
device 1.0, image 1.0:
The metadata will just contain supported_devices as before.
device 1.0, image 1.1:
The metadata will contain:
"new_supported_devices":["device_string1", "device_string2", ...],
"supported_devices":["Image version 1.1 incompatible to device: ..."]
If the device is "legacy", i.e. does not have the updated fwtool.sh,
it will just fail with image check and print the content of
supported_devices. If DEVICE_COMPAT_MESSAGE is set, this will be
printed on old devices as well through the same mechanism. Otherwise
a generic "Please check documentation ..." is appended.
Upgrade can still be performed with -F like when
SUPPORTED_DEVICES has been removed to prevent bricking.
If the device has updated fwtool.sh (but is 1.0), it will just use
the new_supported_devices instead, and work as intended (flashing
with -n will work, flashing without will print the appropriate
warning).
This mechanism should provide a fair tradeoff between simplicity
and functionality.
Since we touched a lot of fields in metadata, this also bumps
metadata_version to 1.1.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We regularly encounter the situation that devices are subject to
changes that will make them incompatible to previous versions.
Removing SUPPORTED_DEVICES will not really be helpful in most of these
cases, as this only helps after a rename.
To solve this situation, this patchset introduces a compatibility
version for devices. In this patch, the actual checks are implemented
into fwtool_check_image():
If an incompatible change is introduced, one can increase either
the minor version (1.0->1.1) or the major version (1.0->2.0).
Minor version increment:
This will still allow sysupgrade, but require to reset config
(-n or SAVE_CONFIG=0). If sysupgrade is called without -n, a
corresponding message will be printed. If sysupgrade is called
with -n, it will just pass, with supported devices being checked
as usual. (Which will allow us to add back SUPPORTED_DEVICES for
many cases.)
Major version increment:
This is meant for potential (rare) cases where sysupgrade is
not possible at all, because it would break the device.
In this case, a warning will be printed, and -n won't help.
If image check fails because of one of the versions parts not
matching, the content of DEVICE_COMPAT_MESSAGE is printed in
addition to the generic message (if set).
For both cases, upgrade can still be forced with -F as usual.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We regularly encounter the situation that devices are subject to
changes that will make them incompatible to previous versions.
Removing SUPPORTED_DEVICES will not really be helpful in most of these
cases, as this only helps after a rename.
To solve this situation, this patchset introduces a compatibility
version for devices. To complement the DEVICE_COMPAT_VERSION set
for the image to be flashed, this implements a compat_version on
the device, so it will have something to compare with the image.
The only viable way to achieve this seems to be via board.d files,
i.e. this is technically adding a compat version for the device's
config.
Like for the network setup, this will set up a command
ucidef_set_compat_version to set the compat_version in board.d.
This will then add a string to /etc/board.json, which will be
translated into uci system config by bin/config_generate.
By this, the compat_version, being a version of the config, will
also be exposed to the user.
As with DEVICE_COMPAT_VERSION, missing uci entry will be assumed
as compat_version "1.0", so we only need to add this if a device
needs to be bumped, e.g.
ucidef_set_compat_version "1.1"
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
28be011 instance: make sure values are not inherited from previous runs
2ae5cbc uxc: remove debugging left-over
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
For a few packages, the current TITLE is too long, so it is not
displayed at all when running make menuconfig. Despite, there is
no indication of OpenSSL vs. wolfSSL in the titles.
Thus, this patch adjusts titles to be generally shorter, and adds
the SSL variant to it.
While at it, make things easier by creating a shared definition for
eapol-test like it's done already for all the other flavors.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Drop outdated and by now broken patchset originally supplied by
Peter Oh in August 2018 but never merged upstream.
Instead add the more promissing rework recently submitted by
Markus Theil who picked up Peter's patchset, fixed and completed it
and added support for HE (802.11ax) in mesh mode.
This is only compile tested and needs some real-life testing.
Fixes: FS#3214
Fixes: 167028b750 ("hostapd: Update to version 2.9 (2019-08-08)")
Fixes: 0a3ec87a66 ("hostapd: update to latest Git hostap_2_9-1238-gdd2daf0848ed")
Fixes: 017320ead3 ("hostapd: bring back mesh patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
c3ca99f jail: serialize hook execution
8ff8970 jail: add some remaining OCI features
9d5fa0a uxc: behave more like a compliant OCI run-time
1274033 uxc: fix create operation
2d811a4 jail: add 'kill' method to container.%s object
08133b8 uxc: use new container.%s kill ubus API
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds a function for generating a valid random MAC address (unset MC
bit / set locally administered bit).
It is necessary for devices which do not have a MAC address programmed
by the manufacturer.
Signed-off-by: David Bauer <mail@david-bauer.net>
Update the U-Boot to version v2020.07. Also replace the Makefile rewrite
with a proper patch, explaining why this hack is needed.
Run-tested: FriendlyARM NanoPi R2S
Signed-off-by: David Bauer <mail@david-bauer.net>
also install the firmware for all the supported boards
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[fix ATF blob path in uboot-rockchip]
Signed-off-by: David Bauer <mail@david-bauer.net>
In imx6, we currently use the model from DTS to derive a board name
manually in /lib/imx6.sh.
However, if we have individual DTS files anyway, we can exploit
generic 02_sysinfo and use the compatible as board name directly.
While at it, remove the wildcards from /lib/upgrade/platform.sh as
these might make code shorter, but are quite unpleasant when grepping
for a specific device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
OpenWrt lately has harmonized device (definition) names to the
pattern vendor_model to improve overall consistency, also with
other values like the DTS compatible.
This patch applies that scheme to the layerscape target.
Since this (intentionally) creates a bigger overlap between DTS names,
compatible, and device definition name, it also moves DEVICE_DTS and
SUPPORTED_DEVICES definitions to the Device/Default blocks.
Apart from that, it also modifies several packages to use consistent
naming in order to keep the $(1) file references working.
While at it, remove one layer of complexity for the setup in
tfa-layerscape package.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The kernel currently floods the ringbuffer with warnings when adding a
mesh interface for a device not support HE 6GHz modes.
Return without warning in this case, as mesh_add_he_6ghz_cap_ie calls
ieee80211_ie_build_he_6ghz_cap regardless of the supported interface
modes.
Signed-off-by: David Bauer <mail@david-bauer.net>
48777de rcS: cast format string to int64_t
a4df90f jail: fix wrong format for 32-bit
c482c5d jail: add support for referencing existing namespaces
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The following patches:
* 972-ath10k_fix-crash-due-to-wrong-handling-of-peer_bw_rxnss_override-parameter.patch
* 973-ath10k_fix-band_center_freq-handling-for-VHT160-in-recent-firmwares.patch
are replaced by this commit in the upstream kernel:
* 3db24065c2c8 ("ath10k: enable VHT160 and VHT80+80 modes")
The following patches were applied upstream:
* 001-rt2800-enable-MFP-support-unconditionally.patch
* 090-wireless-Use-linux-stddef.h-instead-of-stddef.h.patch
The rtw88 driver is now split into multiple kernel modules, just put it
all into one OpenWrt kernel package.
rtl8812au-ct was patched to compile against the mac80211 from kernel
5.8, but not runtime tested.
Add a patch which fixes ath10k on IPQ40XX, this patch was send upstream
and fixes a crash when loading ath10k on this SoC.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq40xx/ map-ac2200]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ever since this package was introduced, the SDK for mt7629 failed to
build as it started failing on this package.
Fixed by porting Hauke's similar patch for uboot-sunxi to uboot-mediatek.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
If using a configuration file for OpenVPN, allow overriding name of the
interface. The reason is that then people could use configuration file
provided by VPN provider directly and override the name of the interface
to include it in correct firewall zone without need to alter the
configuration file.
Signed-off-by: Michal Hrusecky <michal@hrusecky.net>
(cherry picked from commit c93667358515ec078ef4ac96393623ac084e5c9e)
Split out code that parses openvpn configuration file into separate file
that can be later included in various scripts and reused.
Signed-off-by: Michal Hrusecky <michal@hrusecky.net>
(cherry picked from commit 86d8467c8ab792c79809a08c223dd9d40da6da2e)
Previously hostapd would not stop transmitting when a DFS event was
detected and no available channel to switch to was available.
Disable and re-enable the interface to enter DFS state. This way, TX
does not happen until the kernel notifies hostapd about the NOP
expiring.
Signed-off-by: David Bauer <mail@david-bauer.net>
Currently a device which has a DFS channel selected using the UCI
channel setting might switch to a non-DFS channel in case no chanlist is
provided (UCI setting "channels") when the radio detects a DFS event.
Automatically add a chanlist consisting of the configured channel when
the device does not operate in auto-channel mode and no chanlist set to
circumvent this issue.
Signed-off-by: David Bauer <mail@david-bauer.net>
Similar to wireguard, vxlan can configure multiple peers or add specific
entries to the fdb for a single mac address.
While you can still use peeraddr/peer6addr option within the proto
vxlan/vxlan6 section to not break existing configurations, this patch
allows to add multiple sections that conigure fdb entries via the bridge
command. As such, the bridge command is now a dependency of the vxlan
package. (To be honest without the bridge command available, vxlan isn't
very much fun to use or debug at all)
Field names are taken direclty from the bridge command.
Example with all supported parameters, since this hasn't been documented so
far:
config interface 'vx0'
option proto 'vxlan6' # use vxlan over ipv6
# main options
option ip6addr '2001:db8::1' # listen address
option tunlink 'wan6' # optional if listen address given
option peer6addr '2001:db8::2' # now optional
option port '8472' # this is the standard port under linux
option vid '42' # VXLAN Network Identifier to use
option mtu '1430' # vxlan6 has 70 bytes overhead
# extra options
option rxcsum '0' # allow receiving packets without checksum
option txcsum '0' # send packets without checksum
option ttl '16' # specifies the TTL value for outgoing packets
option tos '0' # specifies the TOS value for outgoing packets
option macaddr '11:22:33:44:55:66' # optional, manually specify mac
# default is a random address
Single peer with head-end replication. Corresponds to the following call
to bridge:
$ bridge fdb append 00:00:00:00:00:00 dev vx0 dst 2001:db8::3
config vxlan_peer
option vxlan 'vx0'
option dst '2001:db8::3' # always required
For multiple peers, this section can be repeated for each dst address.
It's possible to specify a multicast address as destination. Useful when
multicast routing is available or within one lan segment:
config vxlan_peer
option vxlan 'vx0'
option dst 'ff02::1337' # multicast group to join.
# all bum traffic will be send there
option via 'eth1' # for multicast, an outgoing interface needs
# to be specified
All available peer options for completeness:
config vxlan_peer
option vxlan 'vx0' # the interface to configure
option lladdr 'aa:bb:cc:dd:ee:ff' # specific mac,
option dst '2001:db8::4' # connected to this peer
option via 'eth0.1' # use this interface only
option port '4789' # use different port for this peer
option vni '23' # override vni for this peer
option src_vni '123' # see man 3 bridge
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
vxlan can be configured without a peer address. This is used to prepare
an interface and add peers later.
Fixes: FS#2743
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
Acked-by: Matthias Schiffer <mschiffer@universe-factory.net>
This fixes a nasty problem introduced in 2.81 which causes random
crashes on systems where there's significant DNS activity over TCP. It
also fixes DNSSEC validation problems with zero-TTL DNSKEY and DS
records.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Further complete OCI container support in ujail:
f5f305e jail: move /tmp/resolv.conf.d to /dev/resolv.conf.d
6f078ae jail: add support for defining devices
686cf7a jail: actually apply filesystem-specific mount options
f91009a jail: refactor default mounts into new structure
66ae2d9 jail: re-implement /proc/sys/net read-write in netns hack
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
9eddf0f jail: fix hooks
1b1286b jail: parse and apply OCI sysctl values
c049047 jail: implement OCI user additionalGIDs
0e1920c jail: read and apply umask from OCI if defined
1c46cc3 jail: parse and apply POSIX rlimits
76adac5 jail: /proc/$pid/oom_score_adj to OCI defined oomScoreAdj
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
8d5208f jail: fix false return in case of nofail mount
b41f76b procd: fix compile if procd-ujail is not selected
86a5105 jail: fs: fix build on uClibc-ng
bfce7d1 jail: fix some more mount options
268126a jail: add support for maskedPaths and readonlyPaths
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This file is always present because it is part of the ltq-dsl-base
package on which these packages depend.
This check would not have been necessary in the past, because the script
was part of the TARGET_LANTIQ on which these packages also depend.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
It does not make sense to install this components on lantiq systems
where the dsl subsystem is not needed/used.
This also makes it possible to use the files also on other targets.
(hopefully ipq401x / FritzBox 7530 in the near future)
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
The last commit to this package that added the pkgconfig file did not
fix the paths to point to the prefix.
This allows packages to find lzo properly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Specifications:
* SoC: MediaTek MT7621A (880 MHz 2c/4t)
* RAM: Nanya NT5CC128M16IP-DIT (256M DDR3-1600)
* Flash: Macronix MX30LF1G18AC-TI (128M NAND)
* Eth: MediaTek MT7621A (10/100/1000 Mbps x5)
* Radio: MT7615N (2.4 GHz & 5 GHz)
4 antennae: 1 internal and 3 non-deatachable
* USB: 3.0 (x1)
* LEDs:
White (x1 logo)
Green (x6 eth + wps)
Orange (x5, hardware-bound)
* Buttons:
Reset (x1)
WPS (x1)
Everything works! Been running it for a couple weeks now and haven't had
any problems. Please let me know if you run into any.
Installation:
Flash factory image through GUI.
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev>
[use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to
DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In the package guidelines, PKG_VERSION is supposed to be used as
"The upstream version number that we're downloading", while
PKG_RELEASE is referred to as "The version of this package Makefile".
Thus, the variables in a strict interpretation provide a clear
distinction between "their" (upstream) version in PKG_VERSION and
"our" (local OpenWrt trunk) version in PKG_RELEASE.
For local (OpenWrt-only) packages, this implies that those will only
need PKG_RELEASE defined, while PKG_VERSION does not apply following
a strict interpretation. While the majority of "our" packages actually
follow that scheme, there are also some that mix both variables or
have one of them defined but keep them at "1".
This is misleading and confusing, which can be observed by the fact
that there typically either one of the variables is never bumped or
the choice of the variable to increase depends on the person doing the
change.
Consequently, this patch aims at clarifying the situation by
consistently using only PKG_RELEASE for "our" packages. To achieve
that, PKG_VERSION is removed there, bumping PKG_RELEASE where
necessary to ensure the resulting package version string is bigger
than before.
During adjustment, one has to make sure that the new resulting composite
package version will not be considered "older" than the previous one.
A useful tool for evaluating that is 'opkg compare-versions'. In
principle, there are the following cases:
1. Sole PKG_VERSION replaced by sole PKG_RELEASE:
In this case, the resulting version string does not change, it's
just the value of the variable put in the file. Consequently, we
do not bump the number in these cases so nobody is tempted to
install the same package again.
2. PKG_VERSION and PKG_RELEASE replaced by sole PKG_RELEASE:
In this case, the resulting version string has been "version-release",
e.g. 1-3 or 1.0-3. For this case, the new PKG_RELEASE will just
need to be higher than the previous PKG_VERSION.
For the cases where PKG_VERSION has always sticked to "1", and
PKG_RELEASE has been incremented, we take the most recent value of
PKG_RELEASE.
Apart from that, a few packages appear to have developed their own
complex versioning scheme, e.g. using x.y.z number for PKG_VERSION
_and_ a PKG_RELEASE (qos-scripts) or using dates for PKG_VERSION
(adb-enablemodem, wwan). I didn't touch these few in this patch.
Cc: Hans Dedecker <dedeckeh@gmail.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Andre Valentin <avalentin@marcant.net>
Cc: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Steven Barth <steven@midlink.org>
Cc: Daniel Golle <dgolle@allnet.de>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Bumping package version has been overlooked in a previous commit.
While at it, use PKG_RELEASE instead of PKG_VERSION, as the latter
is meant for upstream version number only.
(The effective version string for the package would be "3" in both
cases, so there is no harm done for version comparison.)
Fixes: 0453c3866feb ("vxlan: fix udp checksum control")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, passing "rxcsum" and "txcsum" had no effect.
Fixes: 95ab18e0124e ("vxlan: add options to enable and disable UDP
checksums")
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Feature detection doesn't recognize ipset v7 use on kernel v5.x systems
and thus disables the tc ematch function em_ipset.
- backport patch:
* 002-configure-support-ipset-v7.patch:
650591a7a70c configure: support ipset version 7 with kernel version 5
Fixes: 4e0c54bc5bc8 ("kernel: add support for kernel 5.4")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Recent iproute2 5.x versions modified the symbols resolved for plugins,
causing "tc .. action xt .." to fail. Update the list of symbols to fix.
Fixes: b61495409bb3 ("iproute2: tc: reduce size of dynamic symbol table")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Optional instance watchdog timeout and watchdog mode can be set by
adding: procd_set_param $mode $timeout
$mode is an integer [0-1] representing instance watchdog mode of
operation:
0 = disabled
1 = passive mode, client must periodically poke watchdog via ubus
$timeout is an integer representing how often, in seconds, the watchdog must be poked.
Signed-off-by: Daniel Bailey <danielb@meshplusplus.com>
aed7fb3 procd: fix compilation with uClibc-ng
9d0f831 jail: fix segfault with len(uidmap/gidmap) > 1
42a6217 jail: consider PATH for argv in OCI container
83f4b72 jail: actually chdir into OCI defined CWD
fc9f614 jail: parse and run OCI hooks
02eec92 jail: memory allocation fixes
71e75f4 jail: refactor mount support to cover OCI spec
b586e7d jail: don't make mount source read-only
dacab12 uxc: fix 'stop' command
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This release brings parity with the commits Linus released a few hours
ago into 5.8-rc5.
* receive: account for napi_gro_receive never returning GRO_DROP
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands.
* device: implement header_ops->parse_protocol for AF_PACKET
WireGuard uses skb->protocol to determine packet type, and bails out if
it's not set or set to something it's not expecting. For AF_PACKET
injection, we need to support its call chain of:
packet_sendmsg -> packet_snd -> packet_parse_headers ->
dev_parse_header_protocol -> parse_protocol
Without a valid parse_protocol, this returns zero, and wireguard then
rejects the skb. So, this wires up the ip_tunnel handler for layer 3
packets for that case.
* queueing: make use of ip_tunnel_parse_protocol
Now that wg_examine_packet_protocol has been added for general
consumption as ip_tunnel_parse_protocol, it's possible to remove
wg_examine_packet_protocol and simply use the new
ip_tunnel_parse_protocol function directly.
* compat: backport ip_tunnel_parse_protocol and ip_tunnel_header_ops
These are required for moving wg_examine_packet_protocol out of
wireguard and into upstream.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Add support for Marvell MACCHIATObin Single Shot, cortex-a72 based
Marvell ARMADA 8040 Community board. Single Shot was broken as the
device tree is different on the Double Shot Board.
Specifications:
- Quad core Cortex-A72 (up to 2GHz)
- DDR4 DIMM slot with optional ECC and single/dual chip select support
- Dual 10GbE (1/2.5/10GbE) SFP+
2.5GbE (1/2.5GbE) via SFP
1GbE via copper
- SPI Flash
- 3 X SATA 3.0 connectors
- MicroSD connector
- eMMC
- PCI x4 3.0 slot
- USB 2.0 Headers (Internal)
- USB 3.0 connector
- Console port (UART) over microUSB connector
- 20-pin Connector for CPU JTAG debugger
- 2 X UART Headers
- 12V input via DC Jack
- ATX type power connector
- Form Factor: Mini-ITX (170 mm x 170 mm)
More details at http://macchiatobin.net
Installation:
Write the Image to your Micro SD Card and insert it in the
MACCHIATObin Single Shot SD Card Slot.
In the U-Boot Environment:
1. reset U-Boot environment:
env default -a
saveenv
2. prepare U-Boot with boot script:
setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
or manually (hanging lines indicate wrapped one-line command):
setenv fdt_name armada-8040-mcbin-singleshot.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr
$image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv
bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
$kernel_addr - $fdt_addr'
saveenv
On newer Bootloaders (18.12) the Variables have been changed, use:
setenv fdt_name armada-8040-mcbin-singleshot.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr_r
$image_name;ext4load mmc 1:1 $fdt_addr_r $fdt_name;setenv
bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
$kernel_addr_r - $fdt_addr_r'
Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: Alexandra Alth <alexandra@alth.de>
[add specs and installation as provided by Alexandra Alth]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Between kernels 4.20 and 5.0, a new variant of this board has been
introduced ("Single Shot"), and the existing one has been renamed
with the appendix "Double Shot". [1]
This also adjusted the first compatible in the list:
marvell,armada8040-mcbin -> marvell,armada8040-mcbin-doubleshot
This patch updates the OpenWrt implementation of this device by
adjusting the relevant references to that compatible (i.e., our
board name).
To still provide support for 4.19 with our setup, this adds a
small patch to change the compatible there as well.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b1f0bbe2700051886b954192b6c1751233fe0f52
Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The firmware is currently just copied. It can end up with o= on the
device (this is the case for voice_ar9_firmware.bin for instance).
Instead of copying it the Makefile is changed to use the macro
"$(INSTALL_DATA)" in order for the file to be world-readable.
While at it refactor the device node creation in the init script with
loop.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
[removed 2nd part with custom group handling for device nodes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There had been an issue in Layerscape QSPI driver for very long
time, which made squashfs,jffs2 rootfs not work on QSPI NOR.
And the ubifs had been used as a workaround.
Now the issue has been fixed. So convert to use squashfs,jffs2
rootfs on QSPI NOR for Layerscape boards (LS1012ARDB/LS1046ARDB/
LS1088ARDB), and update u-boot bootargs for booting.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The rootfs squashfs is already highly (XZ) compressed. Storing the applet
messages in compressed form will increase the entropy and reduce the overall
image compression ratio.
Size diffs (compressed vs uncompressed):
busybox (the executable): 364596 vs 384804 bytes.
OpenWrt target images (the kernel image is unchanged, obviously):
omnia-medkit-openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs.tar.gz:
9163597 vs 9162531 bytes (1066 bytes difference).
openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin:
9161688 vs 9160600 bytes (1088 bytes difference).
openwrt-mvebu-cortexa9-cznic_turris-omnia-sysupgrade.img.gz:
9729550 vs 9729230 bytes (320 bytes difference).
All in all, we save just a little bit over 1 kiB. As an added bonus, we
also don't have to decompress the messages twice, (first from squashfs,
then from the bzip2 message storage).
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[added additional size comparision diff detaisl]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Zram is only strictly dependent on lzo, not lz4. Break this dependency and
make the lz4 module visible in the configuration, in order for the user to
have the choice of enabling/disabling it, if (s)he sees fit.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The block-mount swapon implementation doesn't support discard, so make zram-swap
depend only on the default BusyBox implementation or, when unavailable, on the
one present in the swap-utils package.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The clock_gettime(CLOCK_MONOTONIC) syscall exists for so long that the first
kernel version to support it is not even specified in the man page [1]. Let's
enable it on BusyBox by default. Otherwise, gettimeofday will be used instead,
which will give wrong results if the date/time is reset (time moving backwards).
[1] https://linux.die.net/man/2/clock_gettime
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
CMake is less error prone that autotools and also compiles faster.
Fixed license information.
Added pkgconfig file to InstallDev so that packages that use it can
find lzo.
Before:
time make package/lzo/compile -j 12
________________________________________________________
Executed in 20.87 secs fish external
usr time 26.95 secs 0.00 micros 26.95 secs
sys time 5.49 secs 305.00 micros 5.49 secs
After:
time make package/lzo/compile -j 12
________________________________________________________
Executed in 13.22 secs fish external
usr time 19.59 secs 328.00 micros 19.59 secs
sys time 4.03 secs 10.00 micros 4.03 secs
Time output is with fish shell. make clean was ran before both attempts.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
f4e9bf73ac5c examples/lua: attempt to highlight some traps
53b9a2123fc6 lua/uloop: fd_add: use absolute indices for arguments
c0941d3289fc lua/uloop: make get_sock_fd capable of absolute addresses
161c25960ba2 lua/uloop: fd_add() better args checking
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Quoting part of original message from eefb5f741015 commit in
linux-firmware repository:
This adds the "minifw" version of the EIP197 firmware, which the inside-
secure driver will use as a fallback if the original full-featured
firmware cannot be found. This allows for using the inside-secure driver
and hardware without access to "official" firmware only available under
NDA.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The block index of u-boot-env changed from mtd1 to mtd3 after upgrading kernel to 5.4.
This patch search the mtd block by label name, work as expect when perform a clean flash.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
This replaces deprecated backticks by more versatile $(...) syntax.
This does not touch lib/upgrade/nand.sh, as there replacement is
not trivial.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
3034eaf jail: use linux/capability.h instead of sys/capability.h
Fixes: b6e440a0f5 ("procd: update to git HEAD")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make sure RF5592 is set for RT5592 chip which apparently sometimes
doesn't have RF defined (but always comes with RF5592).
This patch was originally submitted on linux-wireless by
Tom Psyborg <pozega.tomislav@gmail.com> but got rejected.
Turns out the patch is actually needed.
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable SCSI low-level drivers on targets that don't have it already in
order to fix following build failures on few platforms:
.config:4739:warning: symbol value 'm' invalid for SCSI_LOWLEVEL
* Restart config...
* SCSI low-level drivers
SCSI low-level drivers (SCSI_LOWLEVEL) [Y/n] (NEW) aborted!
Fixes: b88f8202c4ce ("kernel: add iscsi-initator support")
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Arduino Yun is a microcontroller development board, based on Atmel
ATmega32u4 and Atheros AR9331.
Specifications:
- MCU: ATmega32U4
- SoC: AR9331
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: SoC internal
- Ethernet: 1x 10/100Mbps
- USB: 1x 2.0
- MicroSD: 1x SDHC
Notes:
- Stock firmware is based on OpenWrt AA.
- The SoC UART can be accessed only through the MCU.
YunSerialTerminal is recommended for access to serial console.
- Stock firmware uses non-standard 250000 baudrate by default.
- The MCU can be reprogrammed from the SoC with avrdude linuxgpio.
Installation:
1. Update U-Boot environment variables to adapt to new partition scheme.
> setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
> setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
> saveenv
2. Boot into stock firmware normally and perform sysupgrade with
sysupgrade image.
# sysupgrade -n -F /tmp/sysupgrade.bin
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Some devices (e.g. Arduino Yun) need bitwise operations during MAC address
setup. This commit adds generalized versions of macaddr_setbit_la(), which
are helpful when manipulating a single bit in a MAC address.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Instead of building in a default environment which loads our environment
from the FAT partition.... just ask U-Boot to do it.
Submitted upstream at
https://patchwork.ozlabs.org/project/uboot/list/?series=184688
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
For building full SD/eMMC images for Banana Pi R2 we'll want a u-boot
image built for that platform.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Download the boot preloader code from the Banana Pi github repo and make
it available for bootable SD card image creation.
Supports only Banana Pi R2 for now.
Based on work by Alexey Loukianov <lx2@lexa2.ru> and others.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixes following issue:
Package kmod-iscsi-initiator is missing dependencies for the following libraries:
crypto_hash.ko
Fixes: b88f8202c4ce ("kernel: add iscsi-initator support")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds support for the Linksys EA7500 V1 router.
Specification:
- CPU: Qualcomm IPQ8064
- RAM: 256MB
- Flash: NAND 128MB
- WiFi: QCA9982 an+ac + QCA9983 bgn
- Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337)
- USB: 1x USB 3.0 1x USB2.0
- Serial console: RJ-45 115200 8n1 (1V8 Voltage level)
- 2 Buttons
- 1 LED
Known issues:
- Some devices won't flash via web gui
Installation:
- Newer stock images doesn't allow to install custom firmware.
- Please downgrade software to 1.1.2 version. Official firmware:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img
- Do it two times to downgrade all stored images.
- Apply factory image via web-gui.
Serial + TFTP method:
- downgrade to 1.1.2 two times
- connect ehternet and serial cable
- set ip address of tftp server to 192.168.1.254
- put openwrt factory image to tftp folder and rename it to macan.bin
- stop device while booting in u-boot
- run command: "run flashimg"
- run command: "setenv boot_part 1"
- run command "saveenv"
- reset
Back to stock:
- Please use old non-gpg image like this 1.1.2:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img
- ssh to router and copy image to tmp
- use sysupgrade -n -F
Tested by github users: @jack338c and @grzesiczek1
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.
Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A
Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
# ubidetach -p /dev/mtd15
# ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
# fw_setenv bootcmd bootipq
8. Perform reboot.
Recover to stock firmware
-------------------------
1. Execute the following command.
# fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Zyxel NSA310S is a NAS based on Marvell kirkwood SoC.
Specification:
- Processor Marvell 88F6702 1 GHz
- 256MB RAM
- 128MB NAND
- 1x GBE LAN port (PHY: Marvell 88E1318)
- 2x USB 2.0
- 1x SATA
- 3x button
- 7x leds
- serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC)
Known issues:
- no kernel module for RTC. [*]
- buzzer (connected to MPP43) need to be drived by 1kHz signal
- no kernel module for internal MCU connected via I2C[**]
[*]
Karoly Pocsi made simple, unofficial driver for HT1382.
It can be found here:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/
[**]
Karoly Pocsi found how CPU talk with MCU:
It is possible to query the MCU-controlled fan speed and temperature:
i2cget -y 0x0 0x0a 0x07
i2cget -y 0x0 0x0a 0x08
The first value (0x07) is the temperature in ° C, the second (0x08) is
the time in milliseconds to complete one fan revolution (rpm = 60,000 / value).
Info translated from:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/
Installation:
TFTP:
1. Run serial console and go to u-boot.
2. Copy u-boot via tftp and write to NAND:
=> mw 0x0800000 0xffff 0x100000
=> nand erase 0x0 100000
=> setenv ipaddr 192.168.1.2
=> setenv serverip 192.168.1.4
=> tftp 0x0800000 nsa310s-u-boot.kwb
=> nand write 0x0800000 0x0 0x100000
=> reset
3. Run new u-Boot, repair bootcmd and restore MAC address from sticker
=> setenv ethaddr AA:BB:CC:DD:EE:FF
=> saveenv
4. Copy and run initramfs image
=> setenv ipaddr 192.168.1.2
=> setenv serverip 192.168.1.4
=> tftpboot zyxel_nsa310s-initramfs-uImage
=> bootm 0x800000
5. Download sysupgrade image and perform sysupgrade
USB:
1. Prepare usb fat32 drive with u-boot.kwb and initramfs image.
Stick it to USB 2.0 port.
2. Run serial console and go to u-boot.
3. Copy u-boot from usb and write to NAND:
=> mw 0x0800000 0xffff 0x100000
=> nand erase 0x0 100000
=> usb start
=> fatload usb 0 0x0800000 u-boot.kwb
=> nand write 0x0800000 0x0 0x100000
=> reset
4. Run new u-Boot, repair bootcmd and restore MAC address from sticker
=> setenv ethaddr AA:BB:CC:DD:EE:FF
=> saveenv
5. Copy and run initramfs image:
=> usb start
=> fatload usb 0 0x0800000 initramfs-uImage
=> bootm 0x800000
6. Download sysupgrade image and perform sysupgrade.
Based on work ThBexx <thomas.beckler@hotmail.com>
DTS based on dropped support in 0ebdf0c.
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[NSA310s -> NSA310S in DEVICE_MODEL]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
New script for comgt. Should help to fetch balance or any additional information with USSD.
This script uses the standard AT command which should be supported by all modems.
Run-tested on: Mikrotik wAP LTE KIT
Signed-off-by: Kirill Lukonin <klukonin@gmail.com>
[fixed from/sob]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM: 512 MiB
FLASH1: 16 MiB NOR - SPI0
FLASH2: 8 GiB eMMC
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT: Reset, WPS
LED: Power, Mesh, WLAN
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2: On board with BLE module
SPI1: On board socket for Zigbee module
Install via tftp
- NB: need to flash transition image firstly
Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf
Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
Module is needed for using iscsi-initiator userspace applications
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[added missing newline between kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Before this change, setting the verbosity to anything with V=blah would
cause uclibc++ build to print errors to the screen. Now, it the
clibc++ build verbosity will be altered in the following manners:
* V=s will set V=1 in the uclibc++ build
* V=sc will set V=2 in the uclibc++ build
Signed-off-by: Wren Turkal <wt@penguintechs.org>
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"
See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg
Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot
Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo
Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client
1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0
other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)
MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004
Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Upstream in commit 972d723484d8 ("split signkey_type and signature_type
for RSA sha1 vs sha256") has added strict checking of pubkey algorithms
which made keys with SHA-256 hashing algorithm unusable as they still
reuse the `ssh-rsa` public key format. So fix this by disabling the
check for `rsa-sha2-256` pubkeys.
Ref: https://tools.ietf.org/html/rfc8332#section-3
Fixes: d4c80f5b172e ("dropbear: bump to 2020.80")
Tested-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This can be useful when a DFS channel is configured, as the ACS channel
list is taken into account when switching channels after a radar event.
For example, this allows to prevent the SRD channels from being used in
that case.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[reorder structure]
Signed-off-by: David Bauer <mail@david-bauer.net>
This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add commit description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add commit description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This package allows to read battery status information and control the
power state of the RAVPower RP-WD009 power management IC.
Signed-off-by: David Bauer <mail@david-bauer.net>
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.
Hardware
--------
CPU: MediaTek MT7628AN
RAM: 64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN: MediaTek MT7628AN 2T2R b/g/n
MediaTek MT7610E 1T1R n/ac
ETH: 1x FastEthernet
SD: SD Card slot
USB: USB 2.0
Custom PMIC on the I2C bus (address 0x0a).
Installation
------------
1. Press and hold down the reset button.
2. Power up the Device. Keep pressing the reset button for 10
more seconds until the Globe LED lights up.
3. Attach your Computer to the Ethernet port. Assign yourself the
address 10.10.10.1/24.
4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
factory image.
5. The flashing will take around 1 minute. The device will reboot
automatically into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
This reverts commit 930f3c014821df423507c878415c7fb4910a454d.
The build fails with the following build error:
arm-openwrt-linux-muslgnueabi-ld.bfd: drivers/built-in.o: in function `ide_init':
build_dir/target-arm_xscale_musl_eabi/u-boot-nsa310/u-boot-2020.04/drivers/block/ide.c:750: undefined reference to `ide_preinit'
make[4]: *** [Makefile:1700: u-boot] Error 1
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Removing i2c pxa slave
The i2c-pxa is typically not use in slave mode. It does not make sense
to have slave mode enabled by default.
Having slave mode enabled prevents the i2c controller from being reset
if a real slave device such as an SFP is attached to the i2c-pxa bus and
locks it up.
Disable slave mode so that the i2c controller can be reset if the bus is
locked up.
If someone actually has a need for pxa slave mode this can be enabled in
kernel config.
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
/lib/netifd/dhcp.script:
Keep support for 'timesvr' while also supporting 'timesrv'
Add log message indicating deprecation of 'timesvr'
Signed-off-by: Sukru Senli <sukru.senli@iopsys.eu>
the uboot of nsa310 cannot use the network chip
as it is a realtek on the PCIe lanes and not a
Marvell ethernet from the SoC.
Therefore tftp is not possible on this device
and the only way to install is by loading files
from a USB drive.
If the USB subsystem is dead there is no way to
install OpenWrt.
Enable sata support and commands so it can be
used as a fallback in case of USB issues.
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
With package "coreutil-sha256sum" installed "sysupgrade" fails to perform 'sha256sum -s' and instead returns 'invalid option -- 's''.
This is caused due to:
different syntax for a sha256sum status check ('sha256sum --status' with "coreutil-sha256sum")
'/usr/bin/sha256sum' being symlinked to '/usr/bin/gnu-sha256sum' (after installation of "coreutil-sha256sum")
"coreutil-sha256sum" package from the packages feed replaces the Busybox sha256sum
This patch restores for 'sysupgrade' the busybox call to its sha256sum applet.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Remove leds-apu2 out of tree driver. There is a new upstream device gpio
and leds driver stack available for the APUv2 and APUv3 boards from pc
egnines. This new driver stack was add in kernel version 4.15.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
ath9k will already fallback on software-crypto for chipsets not
supporting IEEE802.11w (MFP). So advertising MFP is not dependent
on disabling HW crypto for all traffic entirely.
Tested on Sonicwall SonicPoint Ni (AR9132)
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport patches which fix compile issue for uClibc-ng :
dbrandom.c:174:8: warning: implicit declaration of function 'getrandom'; did you mean 'genrandom'? [-Wimplicit-function-declaration]
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~
genrandom
dbrandom.c:174:36: error: 'GRND_NONBLOCK' undeclared (first use in this function); did you mean 'SOCK_NONBLOCK'?
ret = getrandom(buf, sizeof(buf), GRND_NONBLOCK);
^~~~~~~~~~~~~
SOCK_NONBLOCK
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
- update SPDX license identifier
- use https in URL
- use default PKG_BUILD_DIR
Suggested-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Tested-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* compat: drop centos 8.1 support as 8.2 is now out
Of note, as well, is that we now have both RHEL7 and RHEL8 in our CI at
<https://www.wireguard.com/build-status/>.
* Kbuild: remove -fvisibility=hidden from cflags
This fixes an issue when compiling wireguard as a module for ARM kernels in
THUMB2 mode without the JUMP11 workaround.
* noise: do not assign initiation time in if condition
Style fix.
* device: avoid circular netns references
Fixes a circular reference issue with network namespaces.
* netns: workaround bad 5.2.y backport
This works around a back backport in the 5.2.y series.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
mac80211_get_addr is called from mac80211_generate_mac, where the local variable
initialisation id="${macidx:-0}" suggests that macidx is not always defined.
Probably, idx was supposed to be used instead of $(($macidx + 1)).
Fixes: 4d99db168cf7 ("mac80211: try to get interface addresses from wiphy sysfs 'addresses' if no mask is set")
Signed-off-by: Leon M. George <leon@georgemail.eu>
urandom-seed has a separate Makefile, we can safely remove the definition here.
Fixes: 27bfde9c9f78 ("base-files: move urandom seed bits into separate package")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
"[[" is a bash extension for test. As the ash-implementation is not
fully compatible we drop its usage.
This follows up 3519bf4976b41c
As a result, we also need to move the and/or out of the test brackets.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[squash from two patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The original text was copy/pasted from some other package.
Adjust the package title and description to match the description
on the publishers page.
Signed-off-by: Catalin Patulea <catalinp@google.com>
[slightly adjust content and commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- drop patches (applied upstream):
* 010-backport-change-address-logging.patch
* 020-backport-ed25519-support.patch
* 021-backport-chacha20-poly1305-support.patch
- backport patches:
* 010-backport-disable-toom-and-karatsuba.patch:
reduce dropbear binary size (about ~8Kb).
- refresh patches.
- don't bother anymore with following config options
because they are disabled in upstream too:
* DROPBEAR_3DES
* DROPBEAR_ENABLE_CBC_MODE
* DROPBEAR_SHA1_96_HMAC
- explicitly disable DO_MOTD as it was before commit a1099ed:
upstream has (accidentally) switched it to 0 in release 2019.77,
but reverted back in release 2020.79.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
This replace the shell script header of ldd
when it install to `/usr/bin/ldd` where
`#! /..../staging_dir/host/bin/bash`
should be
`#!/bin/sh`
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Previously, gpio_switch only accepts GPIO pin number as input. Once a
GPIO pin is exported and named by device tree, its pin state cannot be
configured and saved across reboots by UCI.
This patch adds support for named GPIO pins. Thus GPIO pin can be
exported by device tree with active high/low correctly configured,
having human-readable name in /sys/class/gpio/ is also now possible.
More importantly, GPIO pins which are referenced by name will be immune
from pin mapping breakage while unintentional pin number changes are
introduced by kernel or driver updates.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
This option allows adding the ath9k ADC register output as a source
of randomness into the Linux entropy pool at sufficient quality
random data (at least 10 bits and up to 22 bits of min-entropy for
a 32-bit value).
Fixes FS#1444
Signed-off-by: Alan Swanson <reiver@improbability.net>
Ubus patch as it seems have been broken by some rebase in the past as
the location of line that adds ubus object file was in condition for
CONFIG_MACSEC. That condition was adding object files that are not
touched by ubus patch. This means ubus.o does not have to be included in
that case. When it has to be and when build fails is when CONFIG_AP is
set. All files included in wpa_supplicant that are touched by this patch
are in this condition. This means that this is for sure the original
place for it.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
Removes the standalone implementation of stack smashing protection
in gcc's libssp in favour of the native implementation available
in glibc and uclibc. Musl libc already uses its native ssp, so this
patch does not affect musl-based toolchains.
Stack smashing protection configuration options are now uniform
across all supported libc variants.
This also makes kernel-level stack smashing protection available
for x86_64 and i386 builds using non-musl libc.
Signed-off-by: Ian Cooper <iancooper@hotmail.com>
After a hardware reconnect, the control device might be unavailable and
attempting to interact with it will lead to hanging gcom calls, leaving
the protocol setup in an unrecoverable state.
Change the protocol handler to bail out early and notify netifd if the
control device is not defined or if the underlying device node does not
exist.
Also ensure that the "disconnect", "connect" and "setmode" commands are
actually defined before trying to invoke them.
Finally attempt to re-query the device manufacturer if it is unset in
the interface state in order to prevent UNUPPORTED_MODEM errors after
a modem hardware reconnect.
Signed-off-by: Rozhuk Ivan <rozhuk.im@gmail.com>
[reword subject and commit message]
Ref: https://github.com/openwrt/openwrt/pull/2352
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Pass a default --up and --down executable to each started OpenVPN instance
which triggers /etc/hotplug.d/openvpn/ scripts whenever an instance
goes up or down.
User-configured up and down scripts are invoked by the default shipped
01-user hotplug handler to ensure that existing setups continue to work
as before.
As a consequence of this change, the up, down and script_security OpenVPN
options are removed from the option file, since we're always passing them
via the command line, they do not need to get included into the generated
configuration.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
[reword commit message, move hotplug executable to /usr/libexec]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
All devices are using nand images. Built-in MMC/SD modules are not needed
anymore.
Run tested: pogo v4
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Bringing up of station vlan fails if the optional mac entry isn't set.
The default mac "00:00:00:00:00:00", which should match all stations,
is mistakenly set to the non used variable "isolate". This results in
a wrong formatted .psk file which has to be "vlan_id mac key".
fixes: 5aa2ddd0: hostapd: add support for wifi-station and wifi-vlan sections
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072 (2 ports)
USB: 1 x 2.0 (Host controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: White, Blue, Red, Orange
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMR3500. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img
4. Flash the firmware
(IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
(IPQ40xx) # reset
Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[squashed update patch, updated to 5.4, dropped BOARD_NAME,
migrated to SOC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
IPKG_INSTROOT is only set under image builder and we won't be running
this script at build time either, so remove the reference before it gets
cargo-culted into other scripts.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
The folder for the uci-defaults file of this package is wrong, so
the file most probably has not been executed at all for several
years at least.
Fix the folder and remove the useless shebang for the file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Netgear WNDRMAC v1 is a hardware variant of the Netgear WNDR3700 v2
Specifications
==============
* SoC: Atheros AR7161
* RAM: 64mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v1)
Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.
After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v1.
Please use the `sysupgrade` variant for subsequent flashes.
Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3700 page on openwrt.org for details.
https://openwrt.org/toh/netgear/wndr3700#troubleshooting_and_recovery
Signed-off-by: Renaud Lepage <root@cybikbase.com>
[update DTSI include name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Bump to latest Git and refresh all patches in order to get fix for "UPnP
SUBSCRIBE misbehavior in hostapd WPS AP" (CVE-2020-12695).
General security vulnerability in the way the callback URLs in the UPnP
SUBSCRIBE command are used were reported (VU#339275, CVE-2020-12695).
Some of the described issues may be applicable to the use of UPnP in WPS
AP mode functionality for supporting external registrars.
Ref: https://w1.fi/security/2020-1/
Signed-off-by: Petr Štetiar <ynezz@true.cz>
d13290b Fix advertised IPv6 addresses
Don't just serve link-local addresses via mdns, offer all.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When bringing up wifi the first time after boot, these warnings appear:
netifd: radio0 (1370): rm: can't remove '/var/run/hostapd-wlan0.psk': No such file or directory
netifd: radio0 (1370): rm: can't remove '/var/run/hostapd-wlan0.vlan': No such file or directory
Silence them by adding the "-f" option to rm.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
This updates to the last firmware version before the switch to building
from the common firmware branch, which introduces various issues.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
This reverts commit 9e467a764b4e30a04dd0431ea277f6acd26babe0.
The Raspberry Pi firmware recently switched to building from the common
firmware branch. This introduces changes in the core clock handling,
causing various issues.
E.g. enable_uart=1 no longer fixes the core clock frequency to 250MHz.
When the disable-bt DT overlay is not loaded, the core clock frequency
is increased to 400MHz. As a result, the UART baud rate is no longer
correct, and this causes garbled serial console, or communication
problems with HATs that use the UART.
As a workaround, the core clock could be fixed to 250MHz by adding
'core_freq=250' in /boot/config.txt, but as there appear to be other
issues than just the UART being broken, the safer bet is to revert the
firmware for now.
Upstream bug: https://github.com/raspberrypi/firmware/issues/1376
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
As reported in https://github.com/openwrt/packages/issues/12072, the
imagebuilder fails due to a dependency resolution error when the userspace
packages are built using a target that has a different kernel version than
that which is being run. To resolve this, add a virtual kernel package with
the conditional dependency currently used in sqm-scripts. The idea is to
move the sqm-scripts dependency to this virtual package, which hopefully
should be consistent with the actual kernel module being built.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
