mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-10-18 21:48:23 +02:00
mpc85xx: add support for Hewlett Packard MSM460
Hardware -------- CPU: Freescale P1020 2xe500 PPC RAM: 256M DDR3 (Micron MT41J64M16JT-15E:G "D9MNJ") NAND: 128M (Micron 2CA1) BTN: 1x Reset LED: Power - ETH - Radio1 - Radio2 UART: RJ-45 Cisco Pinout - 115200 8N1 Installation ------------ NOTE: You can find a repo with up-to-date instructions as well as the required files here: https://github.com/blocktrron/msm460-flashing Required files ============== You need a command-files as well as a U-Boot image. The command-file has the following content (padded to 131072 bytes). If you copy paste these, remove the newlines! ``` U-BOOT setenv ethaddr 02:03:04:05:06:07; setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; tftpboot 0x3000000 msm460-uboot.bin; nand device; nand erase 0 0xC0000; nand write 0x3000000 0x0 0xC0000; reset ``` You can download the required U-Boot from this repository: https://github.com/blocktrron/u-boot-msm/releases Preparation =========== Prepare a TFTP server serving two files: - U-Boot NAND image as `msm460-uboot.bin`. - OpenWrt factory image as `msm460-factory.bin` - Command-file names `commands.tftp` You can start a TFTP server in the current directory using dnsmasq: ```bash sudo dnsmasq --no-daemon --listen-address=0.0.0.0 \ --port=0 --enable-tftp=enxd0 --tftp-root="$(pwd)" \ --user=root --group=root ``` Replace `enxd0` with the name of your network interface. Procedure ========= 1. Assign yourself the IP-Address 192.168.1.66/24. 3. Connect the Router to the PC while keeping the reset button pressed. 4. The LEDs will eventually begin to flash. They will start to flash faster after around 15 seconds. 5. Release the reset button. 6. Start a new shell 7. Make sure you are currently in the directory where the tftp server is located. 8. Run the following command: ```bash tftp 192.168.1.1 -m binary -c put commands.tftp nflashd.cccc9999 ``` You get the message "Transfer timed out." To find out if you have been successful, please check the blinking LED Pattern. Signed-off-by: David Bauer <mail@david-bauer.net>
This commit is contained in:
David Bauer
parent
7d768a9ba6
commit
af329ec389
@ -16,6 +16,9 @@ extreme-networks,ws-ap3825i)
|
||||
ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth1"
|
||||
ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth0"
|
||||
;;
|
||||
hpe,msm460)
|
||||
ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0"
|
||||
;;
|
||||
esac
|
||||
|
||||
board_config_flush
|
||||
|
||||
@ -16,6 +16,9 @@ aerohive,hiveap-330|\
|
||||
enterasys,ws-ap3715i)
|
||||
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
||||
;;
|
||||
hpe,msm460)
|
||||
ucidef_set_interface_lan "eth0"
|
||||
;;
|
||||
ocedo,panda)
|
||||
ucidef_set_interface_wan "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
|
||||
@ -20,6 +20,11 @@ enterasys,ws-ap3710i|\
|
||||
extreme-networks,ws-ap3825i)
|
||||
mtd_get_mac_ascii cfg2 RADIOADDR${PHYNBR} > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
hpe,msm460)
|
||||
wifi_mac=$(mtd_get_mac_binary colubris-bid 0x1f9bd)
|
||||
[ "$PHYNBR" -eq 0 ] && echo "$wifi_mac" > /sys${DEVPATH}/macaddress
|
||||
[ "$PHYNBR" -eq 1 ] && echo "$(macaddr_add $wifi_mac 16)" > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
ocedo,panda)
|
||||
mtd_get_mac_ascii uboot-env0 wmac$(($PHYNBR + 1)) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
|
||||
@ -13,6 +13,7 @@ platform_do_upgrade() {
|
||||
local board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
hpe,msm460|\
|
||||
ocedo,panda|\
|
||||
sophos,red-15w-rev1|\
|
||||
watchguard,firebox-t10)
|
||||
|
||||
@ -150,6 +150,7 @@ CONFIG_MPIC=y
|
||||
# CONFIG_MPIC_MSGR is not set
|
||||
CONFIG_MPIC_TIMER=y
|
||||
CONFIG_MPILIB=y
|
||||
# CONFIG_MSM460 is not set
|
||||
# CONFIG_MTD_CFI is not set
|
||||
CONFIG_MTD_NAND_CORE=y
|
||||
CONFIG_MTD_NAND_ECC=y
|
||||
|
||||
@ -158,6 +158,7 @@ CONFIG_MPIC=y
|
||||
# CONFIG_MPIC_MSGR is not set
|
||||
CONFIG_MPIC_TIMER=y
|
||||
CONFIG_MPILIB=y
|
||||
# CONFIG_MSM460 is not set
|
||||
# CONFIG_MTD_CFI is not set
|
||||
CONFIG_MTD_NAND_CORE=y
|
||||
CONFIG_MTD_NAND_ECC=y
|
||||
|
||||
238
target/linux/mpc85xx/files/arch/powerpc/boot/dts/msm460.dts
Normal file
238
target/linux/mpc85xx/files/arch/powerpc/boot/dts/msm460.dts
Normal file
@ -0,0 +1,238 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later or MIT
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/include/ "fsl/p1020si-pre.dtsi"
|
||||
/ {
|
||||
model = "Hewlett-Packard MSM460";
|
||||
compatible = "hpe,msm460";
|
||||
|
||||
aliases {
|
||||
led-boot = &system_green;
|
||||
led-failsafe = &system_green;
|
||||
led-running = &system_green;
|
||||
led-upgrade = &system_green;
|
||||
};
|
||||
|
||||
chosen {
|
||||
/* Needed for initramfs */
|
||||
bootargs-override = "console=ttyS0,115200 ubi.mtd=5,2048";
|
||||
stdout-path = &serial0;
|
||||
};
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
lbc: localbus@ffe05000 {
|
||||
reg = <0 0xffe05000 0 0x1000>;
|
||||
ranges = <0x0 0x0 0x0 0xec000000 0x04000000
|
||||
0x1 0x0 0x0 0xff800000 0x00040000
|
||||
0x2 0x0 0x0 0xffa00000 0x00020000
|
||||
0x3 0x0 0x0 0xffb00000 0x00020000>;
|
||||
|
||||
nand@1,0 {
|
||||
compatible = "fsl,p1020-fcm-nand", "fsl,elbc-fcm-nand";
|
||||
reg = <0x1 0x0 0x40000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
reg = <0x0 0xc0000>;
|
||||
label = "u-boot";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c0000 {
|
||||
reg = <0xc0000 0x40000>;
|
||||
label = "colubris-bid";
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_hwinfo_1f822: macaddr@1f822 {
|
||||
/* ETH */
|
||||
compatible = "mac-base";
|
||||
reg = <0x1f822 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
macaddr_hwinfo_1f9bd: macaddr@1f9bd {
|
||||
/* WLAN */
|
||||
compatible = "mac-base";
|
||||
reg = <0x1f9bd 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/* uenv{0,1} and ubi occupy kernel and slash partitions */
|
||||
|
||||
partition@100000 {
|
||||
reg = <0x100000 0x80000>;
|
||||
label = "uboot-env0";
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
reg = <0x180000 0x80000>;
|
||||
label = "uboot-env1";
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
reg = <0x200000 0x300000>;
|
||||
label = "reserved";
|
||||
};
|
||||
|
||||
partition@500000 {
|
||||
reg = <0x500000 0x5f00000>;
|
||||
label = "ubi";
|
||||
};
|
||||
|
||||
partition@6500000 {
|
||||
reg = <0x6500000 0x400000>;
|
||||
label = "pool";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6900000 {
|
||||
reg = <0x6900000 0x15e0000>;
|
||||
label = "flash";
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@7ee0000 {
|
||||
reg = <0x7ee0000 0x20000>;
|
||||
label = "pf";
|
||||
read-only;
|
||||
};
|
||||
|
||||
/* BBT is at the end of the flash - 100000@7f00000 */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
soc: soc@ffe00000 {
|
||||
ranges = <0x0 0x0 0xffe00000 0x100000>;
|
||||
|
||||
i2c@3000 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
gpio0: gpio-controller@fc00 {
|
||||
};
|
||||
|
||||
mdio@24000 {
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0x0>;
|
||||
reset-gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
|
||||
reset-assert-us = <10000>;
|
||||
reset-deassert-us = <10000>;
|
||||
};
|
||||
};
|
||||
|
||||
enet0: ethernet@b0000 {
|
||||
phy-connection-type = "rgmii-id";
|
||||
phy-handle = <&phy0>;
|
||||
nvmem-cells = <&macaddr_hwinfo_1f822 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
enet1: ethernet@b1000 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
enet2: ethernet@b2000 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
usb@22000 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
usb@23000 {
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
pci0: pcie@ffe09000 {
|
||||
ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
|
||||
0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
|
||||
reg = <0 0xffe09000 0 0x1000>;
|
||||
pcie@0 {
|
||||
ranges = <0x2000000 0x0 0xa0000000
|
||||
0x2000000 0x0 0xa0000000
|
||||
0x0 0x20000000
|
||||
|
||||
0x1000000 0x0 0x0
|
||||
0x1000000 0x0 0x0
|
||||
0x0 0x100000>;
|
||||
};
|
||||
};
|
||||
|
||||
pci1: pcie@ffe0a000 {
|
||||
reg = <0 0xffe0a000 0 0x1000>;
|
||||
ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
|
||||
0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
|
||||
pcie@0 {
|
||||
ranges = <0x2000000 0x0 0x80000000
|
||||
0x2000000 0x0 0x80000000
|
||||
0x0 0x20000000
|
||||
|
||||
0x1000000 0x0 0x0
|
||||
0x1000000 0x0 0x0
|
||||
0x0 0x100000>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
system_green: power {
|
||||
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
lan {
|
||||
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_LAN;
|
||||
};
|
||||
|
||||
radio1 {
|
||||
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
function-enumerator = <1>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
radio2 {
|
||||
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
function-enumerator = <2>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
|
||||
buttons {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset-btn";
|
||||
gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/include/ "fsl/p1020si-post.dtsi"
|
||||
@ -0,0 +1,91 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later
|
||||
|
||||
/*
|
||||
* HPE MSM460 Board Setup
|
||||
*
|
||||
* Copyright (C) 2022 David Bauer <mail@david-bauer.net>
|
||||
*
|
||||
* Based on:
|
||||
* mpc85xx_rdb.c:
|
||||
* MPC85xx RDB Board Setup
|
||||
* Copyright 2013 Freescale Semiconductor Inc.
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify it
|
||||
* under the terms of the GNU General Public License as published by the
|
||||
* Free Software Foundation; either version 2 of the License, or (at your
|
||||
* option) any later version.
|
||||
*/
|
||||
|
||||
#include <linux/stddef.h>
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/delay.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <linux/of_platform.h>
|
||||
|
||||
#include <asm/time.h>
|
||||
#include <asm/machdep.h>
|
||||
#include <asm/pci-bridge.h>
|
||||
#include <mm/mmu_decl.h>
|
||||
#include <asm/prom.h>
|
||||
#include <asm/udbg.h>
|
||||
#include <asm/mpic.h>
|
||||
|
||||
#include <sysdev/fsl_soc.h>
|
||||
#include <sysdev/fsl_pci.h>
|
||||
#include "smp.h"
|
||||
|
||||
#include "mpc85xx.h"
|
||||
|
||||
void __init msm_pic_init(void)
|
||||
{
|
||||
struct mpic *mpic;
|
||||
|
||||
mpic = mpic_alloc(NULL, 0,
|
||||
MPIC_BIG_ENDIAN |
|
||||
MPIC_SINGLE_DEST_CPU,
|
||||
0, 256, " OpenPIC ");
|
||||
|
||||
BUG_ON(mpic == NULL);
|
||||
mpic_init(mpic);
|
||||
}
|
||||
|
||||
/*
|
||||
* Setup the architecture
|
||||
*/
|
||||
static void __init msm_setup_arch(void)
|
||||
{
|
||||
if (ppc_md.progress)
|
||||
ppc_md.progress("msm_setup_arch()", 0);
|
||||
|
||||
mpc85xx_smp_init();
|
||||
|
||||
fsl_pci_assign_primary();
|
||||
|
||||
pr_info("MSM460 board from HPE\n");
|
||||
}
|
||||
|
||||
machine_arch_initcall(msm, mpc85xx_common_publish_devices);
|
||||
|
||||
/*
|
||||
* Called very early, device-tree isn't unflattened
|
||||
*/
|
||||
static int __init msm_probe(void)
|
||||
{
|
||||
if (of_machine_is_compatible("hpe,msm460"))
|
||||
return 1;
|
||||
return 0;
|
||||
}
|
||||
|
||||
define_machine(msm) {
|
||||
.name = "P1020 RDB",
|
||||
.probe = msm_probe,
|
||||
.setup_arch = msm_setup_arch,
|
||||
.init_IRQ = msm_pic_init,
|
||||
#ifdef CONFIG_PCI
|
||||
.pcibios_fixup_bus = fsl_pcibios_fixup_bus,
|
||||
.pcibios_fixup_phb = fsl_pcibios_fixup_phb,
|
||||
#endif
|
||||
.get_irq = mpic_get_irq,
|
||||
.calibrate_decr = generic_calibrate_decr,
|
||||
.progress = udbg_progress,
|
||||
};
|
||||
@ -91,6 +91,24 @@ define Device/extreme-networks_ws-ap3825i
|
||||
endef
|
||||
TARGET_DEVICES += extreme-networks_ws-ap3825i
|
||||
|
||||
define Device/hpe_msm460
|
||||
DEVICE_VENDOR := Hewlett-Packard
|
||||
DEVICE_MODEL := MSM460
|
||||
KERNEL = kernel-bin | fit none $(KDIR)/image-$$(DEVICE_DTS).dtb
|
||||
KERNEL_NAME := zImage.la3000000
|
||||
KERNEL_ENTRY := 0x3000000
|
||||
KERNEL_LOADADDR := 0x3000000
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
SUBPAGESIZE := 2048
|
||||
KERNEL_IN_UBI := 1
|
||||
UBINIZE_OPTS := -E 5
|
||||
IMAGES := factory.bin sysupgrade.bin
|
||||
IMAGE/factory.bin := append-ubi
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += hpe_msm460
|
||||
|
||||
define Device/ocedo_panda
|
||||
DEVICE_VENDOR := OCEDO
|
||||
DEVICE_MODEL := Panda
|
||||
@ -104,4 +122,3 @@ define Device/ocedo_panda
|
||||
IMAGE/fdt.bin := append-dtb
|
||||
endef
|
||||
TARGET_DEVICES += ocedo_panda
|
||||
|
||||
|
||||
@ -12,6 +12,7 @@ CONFIG_GPIO_74X164=y
|
||||
CONFIG_HAVE_RCU_TABLE_FREE=y
|
||||
CONFIG_HIVEAP_330=y
|
||||
CONFIG_PANDA=y
|
||||
CONFIG_MSM460=y
|
||||
CONFIG_I2C_CHARDEV=y
|
||||
CONFIG_LEDS_LP5521=y
|
||||
CONFIG_LEDS_LP55XX_COMMON=y
|
||||
|
||||
@ -0,0 +1,30 @@
|
||||
--- a/arch/powerpc/platforms/85xx/Kconfig
|
||||
+++ b/arch/powerpc/platforms/85xx/Kconfig
|
||||
@@ -114,6 +114,17 @@ config FIREBOX_T10
|
||||
This board is a VPN Gateway-Router with a
|
||||
Freescale P1010 SoC.
|
||||
|
||||
+config MSM460
|
||||
+ bool "HPE MSM460"
|
||||
+ select DEFAULT_UIMAGE
|
||||
+ select ARCH_REQUIRE_GPIOLIB
|
||||
+ select GPIO_MPC8XXX
|
||||
+ help
|
||||
+ This option enables support for the HPE MSM460 board.
|
||||
+
|
||||
+ This board is a Concurrent Dual-Band wireless access point with a
|
||||
+ Freescale P1020 SoC.
|
||||
+
|
||||
config MPC8540_ADS
|
||||
bool "Freescale MPC8540 ADS"
|
||||
select DEFAULT_UIMAGE
|
||||
--- a/arch/powerpc/platforms/85xx/Makefile
|
||||
+++ b/arch/powerpc/platforms/85xx/Makefile
|
||||
@@ -21,6 +21,7 @@ obj-$(CONFIG_MPC8536_DS) += mpc8536_ds.
|
||||
obj-$(CONFIG_MPC85xx_DS) += mpc85xx_ds.o
|
||||
obj-$(CONFIG_MPC85xx_MDS) += mpc85xx_mds.o
|
||||
obj-$(CONFIG_MPC85xx_RDB) += mpc85xx_rdb.o
|
||||
+obj-$(CONFIG_MSM460) += msm460.o
|
||||
obj-$(CONFIG_P1010_RDB) += p1010rdb.o
|
||||
obj-$(CONFIG_P1022_DS) += p1022_ds.o
|
||||
obj-$(CONFIG_P1022_RDK) += p1022_rdk.o
|
||||
@ -0,0 +1,30 @@
|
||||
--- a/arch/powerpc/platforms/85xx/Kconfig
|
||||
+++ b/arch/powerpc/platforms/85xx/Kconfig
|
||||
@@ -114,6 +114,17 @@ config FIREBOX_T10
|
||||
This board is a VPN Gateway-Router with a
|
||||
Freescale P1010 SoC.
|
||||
|
||||
+config MSM460
|
||||
+ bool "HPE MSM460"
|
||||
+ select DEFAULT_UIMAGE
|
||||
+ select ARCH_REQUIRE_GPIOLIB
|
||||
+ select GPIO_MPC8XXX
|
||||
+ help
|
||||
+ This option enables support for the HPE MSM460 board.
|
||||
+
|
||||
+ This board is a Concurrent Dual-Band wireless access point with a
|
||||
+ Freescale P1020 SoC.
|
||||
+
|
||||
config MPC8540_ADS
|
||||
bool "Freescale MPC8540 ADS"
|
||||
select DEFAULT_UIMAGE
|
||||
--- a/arch/powerpc/platforms/85xx/Makefile
|
||||
+++ b/arch/powerpc/platforms/85xx/Makefile
|
||||
@@ -19,6 +19,7 @@ obj8259-$(CONFIG_PPC_I8259) += mpc85xx
|
||||
obj-$(CONFIG_MPC85xx_DS) += mpc85xx_ds.o $(obj8259-y)
|
||||
obj-$(CONFIG_MPC85xx_MDS) += mpc85xx_mds.o
|
||||
obj-$(CONFIG_MPC85xx_RDB) += mpc85xx_rdb.o
|
||||
+obj-$(CONFIG_MSM460) += msm460.o
|
||||
obj-$(CONFIG_P1010_RDB) += p1010rdb.o
|
||||
obj-$(CONFIG_P1022_DS) += p1022_ds.o
|
||||
obj-$(CONFIG_P1022_RDK) += p1022_rdk.o
|
||||
Loading…
Reference in New Issue
Block a user