mirror/openwrt
1
0
Fork 0
mirror of https://git.openwrt.org/openwrt/openwrt.git synced 2024-10-19 05:58:53 +02:00
Code Issues

ath79: drop upstreamed patch

Browse Source 
This patch was backported to the 5.4 kernel tree as commit
c2d5c4df27e0 at least since release v5.4.28. Since then, it enables RX
an TX ready override twice.

Signed-off-by: David Bauer <mail@david-bauer.net>
This commit is contained in:
David Bauer 2021-01-01 15:41:33 +01:00
parent 9b1b89229f
commit 9dc15e36c8
2 changed files with 7 additions and 71 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

64
target/linux/ath79/patches-5.4/0060-serial-ar933x_uart-set-UART_CS_-RX-TX-_READY_ORIDE.patch
View File

@ -1,64 +0,0 @@
From patchwork Fri Feb 7 09:53:35 2020
Content-Type: text/plain; charset="utf-8"
MIME-Version: 1.0
Content-Transfer-Encoding: 7bit
X-Patchwork-Submitter: Daniel Golle <daniel@makrotopia.org>
X-Patchwork-Id: 1190470
Date: Fri, 7 Feb 2020 11:53:35 +0200
From: Daniel Golle <daniel@makrotopia.org>
To: linux-serial@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Jiri Slaby <jslaby@suse.com>,
Chuanhong Guo <gch981213@gmail.com>,
Eitan Cohen <eitan@neot-semadar.com>,
Ori Gofen <origofen@gmail.com>
Subject: [PATCH] serial: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDE
Message-ID: <20200207095335.GA179836@makrotopia.org>
MIME-Version: 1.0
Content-Disposition: inline
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk
List-ID: <linux-kernel.vger.kernel.org>
X-Mailing-List: linux-kernel@vger.kernel.org
On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x should not do any harm, so just
set them unconditionally.
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
---
drivers/tty/serial/ar933x_uart.c | 8 ++++++++
1 file changed, 8 insertions(+)
--- a/drivers/tty/serial/ar933x_uart.c
+++ b/drivers/tty/serial/ar933x_uart.c
@@ -290,6 +290,10 @@ static void ar933x_uart_set_termios(stru
ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
AR933X_UART_CS_TX_READY_ORIDE | AR933X_UART_CS_RX_READY_ORIDE);
+ /* enable RX and TX ready overide */
+ ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
+ AR933X_UART_CS_TX_READY_ORIDE | AR933X_UART_CS_RX_READY_ORIDE);
+
/* reenable the UART */
ar933x_uart_rmw(up, AR933X_UART_CS_REG,
AR933X_UART_CS_IF_MODE_M << AR933X_UART_CS_IF_MODE_S,
@@ -424,6 +428,10 @@ static int ar933x_uart_startup(struct ua
/* enable RX and TX ready overide */
ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
+ AR933X_UART_CS_TX_READY_ORIDE | AR933X_UART_CS_RX_READY_ORIDE);
+
+ /* enable RX and TX ready overide */
+ ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
AR933X_UART_CS_TX_READY_ORIDE | AR933X_UART_CS_RX_READY_ORIDE);
/* Enable RX interrupts */

14
target/linux/ath79/patches-5.4/0061-tty-serial-ar933x-uart-rs485-gpio.patch
View File

@ -160,7 +160,7 @@ v2: use bool to indicate ongoing half-duplex send, use it afterwards
}
static void ar933x_uart_break_ctl(struct uart_port *port, int break_state)
@@ -340,11 +397,20 @@ static void ar933x_uart_rx_chars(struct
@@ -336,11 +393,20 @@ static void ar933x_uart_rx_chars(struct
static void ar933x_uart_tx_chars(struct ar933x_uart_port *up)
{
struct circ_buf *xmit = &up->port.state->xmit;
@ -181,7 +181,7 @@ v2: use bool to indicate ongoing half-duplex send, use it afterwards
count = up->port.fifosize;
do {
unsigned int rdata;
@@ -372,8 +438,14 @@ static void ar933x_uart_tx_chars(struct
@@ -368,8 +434,14 @@ static void ar933x_uart_tx_chars(struct
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&up->port);
@ -197,7 +197,7 @@ v2: use bool to indicate ongoing half-duplex send, use it afterwards
}
static irqreturn_t ar933x_uart_interrupt(int irq, void *dev_id)
@@ -435,8 +507,7 @@ static int ar933x_uart_startup(struct ua
@@ -427,8 +499,7 @@ static int ar933x_uart_startup(struct ua
AR933X_UART_CS_TX_READY_ORIDE | AR933X_UART_CS_RX_READY_ORIDE);
/* Enable RX interrupts */
@ -207,7 +207,7 @@ v2: use bool to indicate ongoing half-duplex send, use it afterwards
spin_unlock_irqrestore(&up->port.lock, flags);
@@ -519,6 +590,21 @@ static const struct uart_ops ar933x_uart
@@ -511,6 +582,21 @@ static const struct uart_ops ar933x_uart
.verify_port = ar933x_uart_verify_port,
};
@ -229,7 +229,7 @@ v2: use bool to indicate ongoing half-duplex send, use it afterwards
#ifdef CONFIG_SERIAL_AR933X_CONSOLE
static struct ar933x_uart_port *
ar933x_console_ports[CONFIG_SERIAL_AR933X_NR_UARTS];
@@ -688,6 +774,8 @@ static int ar933x_uart_probe(struct plat
@@ -680,6 +766,8 @@ static int ar933x_uart_probe(struct plat
goto err_disable_clk;
}
@ -238,7 +238,7 @@ v2: use bool to indicate ongoing half-duplex send, use it afterwards
port->mapbase = mem_res->start;
port->line = id;
port->irq = irq_res->start;
@@ -698,6 +786,7 @@ static int ar933x_uart_probe(struct plat
@@ -690,6 +778,7 @@ static int ar933x_uart_probe(struct plat
port->regshift = 2;
port->fifosize = AR933X_UART_FIFO_SIZE;
port->ops = &ar933x_uart_ops;
@ -246,7 +246,7 @@ v2: use bool to indicate ongoing half-duplex send, use it afterwards
baud = ar933x_uart_get_baud(port->uartclk, AR933X_UART_MAX_SCALE, 1);
up->min_baud = max_t(unsigned int, baud, AR933X_UART_MIN_BAUD);
@@ -705,6 +794,18 @@ static int ar933x_uart_probe(struct plat
@@ -697,6 +786,18 @@ static int ar933x_uart_probe(struct plat
baud = ar933x_uart_get_baud(port->uartclk, 0, AR933X_UART_MAX_STEP);
up->max_baud = min_t(unsigned int, baud, AR933X_UART_MAX_BAUD);