mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2024-10-18 21:48:23 +02:00
ipq40xx: add support for GL.iNet GL-A1300
Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2 USB: 1 x USB 3.0 port Button: 1 x Reset button Switch: 1 x Mode switch LED: 1 x Blue LED + 1 x White LED Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi (IPQ40xx) # nand erase 0 0x8000000 (IPQ40xx) # nand write 0x84000000 0 $filesize By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
This commit is contained in:
Weiping Yang
Hauke Mehrtens
parent
79107116d1
commit
9945d05171
@ -34,6 +34,7 @@ case "$board" in
|
||||
alfa-network,ap120c-ac|\
|
||||
devolo,magic-2-wifi-next|\
|
||||
edgecore,ecw5211|\
|
||||
glinet,gl-a1300 |\
|
||||
glinet,gl-ap1300|\
|
||||
glinet,gl-b1300|\
|
||||
glinet,gl-b2200|\
|
||||
|
||||
@ -30,6 +30,7 @@ ALLWIFIBOARDS:= \
|
||||
edgecore_ecw5410 \
|
||||
edgecore_oap100 \
|
||||
extreme-networks_ws-ap3915i \
|
||||
glinet_gl-a1300 \
|
||||
glinet_gl-ap1300 \
|
||||
glinet_gl-s1300 \
|
||||
linksys_ea8300 \
|
||||
@ -105,6 +106,7 @@ $(eval $(call generate-ipq-wifi-package,devolo_magic-2-wifi-next,devolo Magic 2
|
||||
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
|
||||
$(eval $(call generate-ipq-wifi-package,edgecore_oap100,Edgecore OAP100))
|
||||
$(eval $(call generate-ipq-wifi-package,extreme-networks_ws-ap3915i,Edgecore OAP100))
|
||||
$(eval $(call generate-ipq-wifi-package,glinet_gl-a1300,GL.iNet GL-A1300))
|
||||
$(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
|
||||
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
|
||||
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
|
||||
|
||||
BIN
package/firmware/ipq-wifi/board-glinet_gl-a1300.qca4019
Normal file
BIN
package/firmware/ipq-wifi/board-glinet_gl-a1300.qca4019
Normal file
Binary file not shown.
@ -58,6 +58,7 @@ ipq40xx_setup_interfaces()
|
||||
compex,wpj428)
|
||||
ucidef_set_interface_lan "lan1 lan2"
|
||||
;;
|
||||
glinet,gl-a1300|\
|
||||
glinet,gl-b1300|\
|
||||
mobipromo,cm520-79f)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
|
||||
|
||||
@ -111,6 +111,7 @@ platform_do_upgrade() {
|
||||
edgecore,ecw5211 |\
|
||||
edgecore,oap100 |\
|
||||
engenius,eap2200 |\
|
||||
glinet,gl-a1300 |\
|
||||
glinet,gl-ap1300 |\
|
||||
luma,wrtq-329acn |\
|
||||
mobipromo,cm520-79f |\
|
||||
|
||||
@ -0,0 +1,326 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "GL.iNet GL-A1300";
|
||||
compatible = "glinet,gl-a1300", "qcom,ipq4019";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_run;
|
||||
led-failsafe = &led_run;
|
||||
led-running = &led_run;
|
||||
led-upgrade = &led_run;
|
||||
label-mac-device = &swport4;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1";
|
||||
};
|
||||
|
||||
soc {
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
/* select hostmode */
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
switch {
|
||||
label = "switch-button";
|
||||
gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_SETUP>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_run: blue {
|
||||
label = "blue:status";
|
||||
gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
white {
|
||||
label = "white:status";
|
||||
gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio_export {
|
||||
compatible = "gpio-export";
|
||||
|
||||
usb {
|
||||
gpio-export,name = "usb_power";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&spi0_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 5 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x00000000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x00040000 0x00020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "QSEE";
|
||||
reg = <0x00060000 0x00060000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c0000 {
|
||||
label = "CDT";
|
||||
reg = <0x000c0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@d0000 {
|
||||
label = "DDRPARAMS";
|
||||
reg = <0x000d0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@e0000 {
|
||||
label = "APPSBLENV"; /* uboot env*/
|
||||
reg = <0x000e0000 0x00010000>;
|
||||
};
|
||||
|
||||
partition@f0000 {
|
||||
label = "APPSBL"; /* uboot */
|
||||
reg = <0x000f0000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@170000 {
|
||||
label = "ART";
|
||||
reg = <0x00170000 0x00010000>;
|
||||
read-only;
|
||||
compatible = "nvmem-cells";
|
||||
|
||||
precal_art_1000: precal@1000 {
|
||||
reg = <0x1000 0x2f20>;
|
||||
};
|
||||
|
||||
precal_art_5000: precal@5000 {
|
||||
reg = <0x5000 0x2f20>;
|
||||
};
|
||||
|
||||
macaddr_gmac0: macaddr@0 {
|
||||
reg = <0x0 0x6>;
|
||||
};
|
||||
|
||||
macaddr_gmac1: macaddr@6 {
|
||||
reg = <0x6 0x6>;
|
||||
};
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "log";
|
||||
reg = <0x00180000 0x00020000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
spi-nand@1 {
|
||||
compatible = "spi-nand";
|
||||
reg = <1>;
|
||||
spi-max-frequency = <24000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "ubi";
|
||||
reg = <0x00000000 0x08000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
i2c_0_pins: i2c_0_pinmux {
|
||||
pinmux {
|
||||
pins = "gpio58", "gpio59";
|
||||
function = "blsp_i2c0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi0_pins: spi0_pinmux {
|
||||
mux_spi {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
mux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54", "gpio5";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_i2c3 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&i2c_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&swport3 {
|
||||
status = "okay";
|
||||
|
||||
label = "lan2";
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_gmac0>;
|
||||
mac-address-increment = <2>;
|
||||
};
|
||||
|
||||
&swport4 {
|
||||
status = "okay";
|
||||
|
||||
label = "lan1";
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_gmac0>;
|
||||
};
|
||||
|
||||
&swport5 {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_gmac1>;
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
nvmem-cell-names = "pre-calibration";
|
||||
nvmem-cells = <&precal_art_1000>;
|
||||
qcom,ath10k-calibration-variant = "GL-A1300";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
nvmem-cell-names = "pre-calibration";
|
||||
nvmem-cells = <&precal_art_5000>;
|
||||
qcom,ath10k-calibration-variant = "GL-A1300";
|
||||
};
|
||||
@ -565,6 +565,20 @@ endef
|
||||
# Missing DSA Setup
|
||||
#TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
|
||||
|
||||
define Device/glinet_gl-a1300
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := GL.iNet
|
||||
DEVICE_MODEL := GL-A1300
|
||||
SOC := qcom-ipq4018
|
||||
DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 131072k
|
||||
DEVICE_PACKAGE := ipq-wifi-glinet_gl-a1300
|
||||
endef
|
||||
TARGET_DEVICES += glinet_gl-a1300
|
||||
|
||||
define Device/glinet_gl-ap1300
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
|
||||
Loading…
Reference in New Issue
Block a user