ath79: add support for ALFA Network N2Q

ALFA Network N2Q is an outdoor N300 AP/CPE based on Qualcomm/Atheros
QCA9531 v2. This model is a successor of the old N2 which was based
on Atheros AR7240. FCC ID: 2AB8795311.

Specifications:

- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2T2R 2.4 GHz Wi-Fi with ext. PA (Skyworks SE2623L) and LNA
- 2x 10/100 Mbps Ethernet with passive PoE input in one port (24 V)
- PoE pass through in second port (controlled by GPIO)
- support for optional 802.3af/at PoE module
- 1x mini PCIe slot (PCIe bus, extra 4.2 V for high power cards)
- 2x IPEX/U.FL connectors on PCB
- 1x USB 2.0 mini Type-B (power controlled by GPIO)
- 8x LED (7 of them are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- UART (4-pin, 2.54 mm pitch) header on PCB
- LEDs (2x 5-pin, 2.54 mm pitch) header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

target/linux/ath79/dts/qca9531_alfa-network_n2q.dts

@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9531_alfa-network_r36a.dtsi"
+
+/ {
+	model = "ALFA Network N2Q";
+	compatible = "alfa-network,n2q", "qca,qca9531";
+
+	aliases {
+		led-boot = &led_usb;
+		led-failsafe = &led_usb;
+		led-upgrade = &led_usb;
+	};
+
+	gpio-export-pcf8574 {
+		compatible = "gpio-export";
+		#size-cells = <0>;
+
+		poe-passthrough {
+			gpio-export,name = "poe-passthrough";
+			gpio-export,output = <1>;
+			gpios = <&pcf8574 0 GPIO_ACTIVE_LOW>;
+		};
+
+		usb-power {
+			gpio-export,name = "usb-power";
+			gpio-export,output = <0>;
+			gpios = <&pcf8574 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sda-gpios = <&gpio 11 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio  3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+		pcf8574: pcf8574@20 {
+			compatible = "nxp,pcf8574";
+			reg = <0x20>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&enable_gpio4 &enable_gpio16>;
+
+		lan1 {
+			label = "n2q:orange:lan1";
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+		};
+
+		lan2 {
+			label = "n2q:orange:lan2";
+			gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+		};
+
+		led_usb: usb {
+			label = "n2q:green:usb";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "usbport";
+			trigger-sources = <&hub_port0>;
+		};
+
+		minipcie {
+			label = "n2q:green:minipcie";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan {
+			label = "n2q:green:wlan";
+			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+	};
+
+	leds-pcf8574 {
+		compatible = "gpio-leds";
+
+		poe-passthrough {
+			label = "n2q:green:poe-passthrough";
+			gpios = <&pcf8574 1 GPIO_ACTIVE_LOW>;
+		};
+
+		signal1 {
+			label = "n2q:red:signal1";
+			gpios = <&pcf8574 3 GPIO_ACTIVE_LOW>;
+		};
+
+		signal2 {
+			label = "n2q:orange:signal2";
+			gpios = <&pcf8574 4 GPIO_ACTIVE_LOW>;
+		};
+
+		signal3 {
+			label = "n2q:green:signal3";
+			gpios = <&pcf8574 5 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&eth0 {
+	mtd-mac-address = <&art 0x1002>;
+	mtd-mac-address-increment = <(-2)>;
+};
+
+&eth1 {
+	mtd-mac-address = <&art 0x1002>;
+	mtd-mac-address-increment = <(-1)>;
+};
+
+&pcie0 {
+	status = "okay";
+};

target/linux/ath79/dts/qca9531_alfa-network_r36a.dts

@@ -1,57 +1,18 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 
-#include "qca953x.dtsi"
+#include "qca9531_alfa-network_r36a.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
 
 / {
 	model = "ALFA Network R36A";
 	compatible = "alfa-network,r36a", "qca,qca9531";
 
 	aliases {
-		label-mac-device = &wmac;
 		led-boot = &led_status;
 		led-failsafe = &led_status;
 		led-running = &led_status;
 		led-upgrade = &led_status;
 	};
 
-	gpio-export {
-		compatible = "gpio-export";
-		#size-cells = <0>;
-
-		usb-power {
-			gpio-export,name = "usb-power";
-			gpio-export,output = <1>;
-			gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
-		};
-
-		watchdog-enable {
-			gpio-export,name = "watchdog-enable";
-			gpio-export,output = <1>;
-			gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	keys {
-		compatible = "gpio-keys";
-
-		reset {
-			label = "reset";
-			linux,code = <KEY_RESTART>;
-			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
-			debounce-interval = <60>;
-		};
-
-		rfkill {
-			label = "rfkill";
-			linux,code = <KEY_RFKILL>;
-			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
-			debounce-interval = <60>;
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 
@@ -86,20 +47,9 @@
 			linux,default-trigger = "phy0tpt";
 		};
 	};
-
-	watchdog {
-		compatible = "linux,wdt-gpio";
-		gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
-		hw_algo = "toggle";
-		hw_margin_ms = <25000>;
-		always-running;
-	};
 };
 
 &eth0 {
-	status = "okay";
-
-	phy-handle = <&swphy4>;
 	mtd-mac-address = <&art 0x0>;
 };
 
@@ -111,80 +61,19 @@
 	mtd-mac-address = <&art 0x6>;
 };
 
-&pinmux {
+&gpio_export {
-	enable_gpio4: pinmux_enable_gpio4 {
+	usb-power {
-		pinctrl-single,bits = <0x04 0x0 0xff>;
+		gpio-export,name = "usb-power";
-	};
+		gpio-export,output = <1>;
-
+		gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
-	enable_gpio16: pinmux_enable_gpio16 {
-		pinctrl-single,bits = <0x10 0x0 0xff>;
 	};
 };
 
-&spi {
+&keys {
-	status = "okay";
+	rfkill {
-
+		label = "rfkill";
-	num-cs = <1>;
+		linux,code = <KEY_RFKILL>;
-
+		gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
-	flash@0 {
+		debounce-interval = <60>;
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <50000000>;
-		m25p,fast-read;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "u-boot";
-				reg = <0x000000 0x060000>;
-				read-only;
-			};
-
-			partition@60000 {
-				label = "u-boot-env";
-				reg = <0x060000 0x010000>;
-			};
-
-			art: partition@70000 {
-				label = "art";
-				reg = <0x070000 0x010000>;
-				read-only;
-			};
-
-			partition@80000 {
-				compatible = "denx,uimage";
-				label = "firmware";
-				reg = <0x080000 0xf80000>;
-			};
-		};
 	};
 };
-
-&uart {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	hub_port0: port@1 {
-		reg = <1>;
-		#trigger-source-cells = <0>;
-	};
-};
-
-&usb_phy {
-	status = "okay";
-};
-
-&wmac {
-	status = "okay";
-
-	mtd-cal-data = <&art 0x1000>;
-};

target/linux/ath79/dts/qca9531_alfa-network_r36a.dtsi

@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca953x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		label-mac-device = &wmac;
+	};
+
+	gpio_export: gpio-export {
+		compatible = "gpio-export";
+		#size-cells = <0>;
+
+		watchdog-enable {
+			gpio-export,name = "watchdog-enable";
+			gpio-export,output = <1>;
+			gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys: keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	watchdog {
+		compatible = "linux,wdt-gpio";
+		gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+		hw_algo = "toggle";
+		hw_margin_ms = <25000>;
+		always-running;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	phy-handle = <&swphy4>;
+};
+
+&pinmux {
+	enable_gpio4: pinmux_enable_gpio4 {
+		pinctrl-single,bits = <0x04 0x0 0xff>;
+	};
+
+	enable_gpio16: pinmux_enable_gpio16 {
+		pinctrl-single,bits = <0x10 0x0 0xff>;
+	};
+};
+
+&spi {
+	status = "okay";
+
+	num-cs = <1>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x060000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "u-boot-env";
+				reg = <0x060000 0x010000>;
+			};
+
+			art: partition@70000 {
+				label = "art";
+				reg = <0x070000 0x010000>;
+				read-only;
+			};
+
+			partition@80000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x080000 0xf80000>;
+			};
+		};
+	};
+};
+
+&uart {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub_port0: port@1 {
+		reg = <1>;
+		#trigger-source-cells = <0>;
+	};
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&wmac {
+	status = "okay";
+
+	mtd-cal-data = <&art 0x1000>;
+};

target/linux/ath79/generic/base-files/etc/board.d/01_leds

@@ -17,6 +17,14 @@ alfa-network,ap121fe|\
 avm,fritz450e)
 	ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0"
 	;;
+alfa-network,n2q)
+	ucidef_set_led_netdev "lan2" "LAN2" "$boardname:orange:lan2" "eth1"
+	ucidef_set_led_switch "lan1" "LAN1" "$boardname:orange:lan1" "switch0" "0x10"
+	ucidef_set_rssimon "wlan0" "200000" "1"
+	ucidef_set_led_rssi "signal1" "SIGNAL1" "$boardname:red:signal1" "wlan0" "1" "100"
+	ucidef_set_led_rssi "signal2" "SIGNAL2" "$boardname:orange:signal2" "wlan0" "33" "100"
+	ucidef_set_led_rssi "signal3" "SIGNAL3" "$boardname:green:signal3" "wlan0" "66" "100"
+	;;
 alfa-network,r36a)
 	ucidef_set_led_netdev "lan" "LAN" "$boardname:blue:lan" "eth0"
 	ucidef_set_led_switch "wan" "WAN" "$boardname:blue:wan" "switch0" "0x10"

target/linux/ath79/generic/base-files/etc/board.d/02_network

@@ -78,6 +78,12 @@ ath79_setup_interfaces()
 	alfa-network,ap121fe)
 		ucidef_set_interface_lan "eth0 usb0"
 		;;
+	alfa-network,n2q|\
+	devolo,dvl1200e|\
+	devolo,dvl1750e|\
+	ocedo,ursus)
+		ucidef_set_interface_lan "eth0 eth1"
+		;;
 	avm,fritz4020|\
 	pcs,cr3000|\
 	tplink,archer-c58-v1|\
@@ -147,11 +153,6 @@ ath79_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0@eth0" "3:lan" "2:wan"
 		;;
-	devolo,dvl1200e|\
-	devolo,dvl1750e|\
-	ocedo,ursus)
-		ucidef_set_interface_lan "eth0 eth1"
-		;;
 	devolo,magic-2-wifi)
 		ucidef_add_switch "switch0" \
 			"0@eth0" "2:wan" "3:lan" "4:lan"
@@ -402,6 +403,7 @@ ath79_setup_macs()
 		;;
 	alfa-network,ap121f|\
 	alfa-network,ap121fe|\
+	alfa-network,n2q|\
 	alfa-network,r36a|\
 	engenius,ens202ext-v1)
 		label_mac=$(mtd_get_mac_binary art 0x1002)

target/linux/ath79/image/generic.mk

@@ -237,6 +237,16 @@ define Device/alfa-network_ap121fe
 endef
 TARGET_DEVICES += alfa-network_ap121fe
 
+define Device/alfa-network_n2q
+  SOC := qca9531
+  DEVICE_VENDOR := ALFA Network
+  DEVICE_MODEL := N2Q
+  DEVICE_PACKAGES := kmod-i2c-gpio kmod-gpio-pcf857x kmod-usb2 \
+	kmod-usb-ledtrig-usbport rssileds
+  IMAGE_SIZE := 15872k
+endef
+TARGET_DEVICES += alfa-network_n2q
+
 define Device/alfa-network_r36a
   SOC := qca9531
   DEVICE_VENDOR := ALFA Network