# generated by Slic3r Prusa Edition 1.41.2+win64 on 2019-02-09 at 07:56:26 [print:0.2mm Layer Height - VORON PARTS - Slic3r_config_bundle] avoid_crossing_perimeters = 0 bottom_solid_layers = 5 bridge_acceleration = 0 bridge_angle = 0 bridge_flow_ratio = 0.8 bridge_speed = 20 brim_width = 0 clip_multipart_objects = 0 compatible_printers = compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 elefant_foot_compensation = 0 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.4 external_perimeter_speed = 50 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.4 fill_angle = 45 fill_density = 40% fill_pattern = cubic first_layer_acceleration = 0 first_layer_extrusion_width = 0.4 first_layer_height = 120% first_layer_speed = 25 gap_fill_speed = 40 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.4 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 100 inherits = interface_shells = 0 layer_height = 0.2 max_print_speed = 300 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = V2-[input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.4 perimeter_speed = 70 perimeters = 4 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 1 skirt_distance = 3 skirt_height = 1 skirts = 3 small_perimeter_speed = 40 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.4 solid_infill_speed = 100 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_auto = 1 support_material_buildplate_only = 1 support_material_contact_distance = 0.2 support_material_enforce_layers = 2 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 50 support_material_synchronize_layers = 0 support_material_threshold = 60 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 0 threads = 16 top_infill_extrusion_width = 0.4 top_solid_infill_speed = 50 top_solid_layers = 5 travel_speed = 300 wipe_tower = 0 wipe_tower_bridging = 10 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 [print:0.2mm VORON PARTS - XY Only] avoid_crossing_perimeters = 0 bottom_solid_layers = 8 bridge_acceleration = 0 bridge_angle = 0 bridge_flow_ratio = 0.8 bridge_speed = 20 brim_width = 0 clip_multipart_objects = 0 compatible_printers = compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 elefant_foot_compensation = 0 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.4 external_perimeter_speed = 50 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.4 fill_angle = 45 fill_density = 50% fill_pattern = cubic first_layer_acceleration = 0 first_layer_extrusion_width = 0.4 first_layer_height = 120% first_layer_speed = 30 gap_fill_speed = 40 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.4 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 100 inherits = interface_shells = 0 layer_height = 0.2 max_print_speed = 300 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = V2-[input_filename_base].gcode overhangs = 0 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.4 perimeter_speed = 70 perimeters = 5 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 1 skirt_distance = 3 skirt_height = 1 skirts = 3 small_perimeter_speed = 50 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.4 solid_infill_speed = 100 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_auto = 1 support_material_buildplate_only = 1 support_material_contact_distance = 0.2 support_material_enforce_layers = 2 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 50 support_material_synchronize_layers = 0 support_material_threshold = 60 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 0 threads = 16 top_infill_extrusion_width = 0.4 top_solid_infill_speed = 50 top_solid_layers = 8 travel_speed = 300 wipe_tower = 0 wipe_tower_bridging = 10 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 [print:0.4+0.2 - DETAIL - PETG] avoid_crossing_perimeters = 0 bottom_solid_layers = 5 bridge_acceleration = 0 bridge_angle = 0 bridge_flow_ratio = 0.8 bridge_speed = 20 brim_width = 0 clip_multipart_objects = 0 compatible_printers = "0.4mm - PETG" compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 elefant_foot_compensation = 0 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.4 external_perimeter_speed = 35 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.4 fill_angle = 45 fill_density = 5% fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_extrusion_width = 0.45 first_layer_height = 120% first_layer_speed = 30 gap_fill_speed = 35 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.45 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 25% infill_speed = 50 inherits = interface_shells = 0 layer_height = 0.2 max_print_speed = 300 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.4 perimeter_speed = 50 perimeters = 3 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 1 skirt_distance = 3 skirt_height = 1 skirts = 2 small_perimeter_speed = 25 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.4 solid_infill_speed = 50 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_auto = 1 support_material_buildplate_only = 1 support_material_contact_distance = 0.2 support_material_enforce_layers = 2 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 35 support_material_synchronize_layers = 0 support_material_threshold = 60 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 0 threads = 16 top_infill_extrusion_width = 0.4 top_solid_infill_speed = 35 top_solid_layers = 5 travel_speed = 300 wipe_tower = 0 wipe_tower_bridging = 10 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 [print:0.4+0.2 - VP - PC] avoid_crossing_perimeters = 0 bottom_solid_layers = 8 bridge_acceleration = 0 bridge_angle = 0 bridge_flow_ratio = 0.8 bridge_speed = 20 brim_width = 0 clip_multipart_objects = 0 compatible_printers = "0.4mm - PC" compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 elefant_foot_compensation = 0 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.4 external_perimeter_speed = 50 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.4 fill_angle = 135 fill_density = 50% fill_pattern = gyroid first_layer_acceleration = 0 first_layer_extrusion_width = 0.45 first_layer_height = 0.3 first_layer_speed = 20 gap_fill_speed = 40 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.45 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 25% infill_speed = 100 inherits = interface_shells = 0 layer_height = 0.2 max_print_speed = 300 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.4 perimeter_speed = 70 perimeters = 4 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 1 skirt_distance = 3 skirt_height = 1 skirts = 2 small_perimeter_speed = 25 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.4 solid_infill_speed = 100 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_auto = 1 support_material_buildplate_only = 1 support_material_contact_distance = 0.2 support_material_enforce_layers = 2 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 50 support_material_synchronize_layers = 0 support_material_threshold = 60 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 0 threads = 16 top_infill_extrusion_width = 0.4 top_solid_infill_speed = 50 top_solid_layers = 8 travel_speed = 300 wipe_tower = 0 wipe_tower_bridging = 10 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 [print:0.6+0.3 - DETAIL] avoid_crossing_perimeters = 0 bottom_solid_layers = 6 bridge_acceleration = 0 bridge_angle = 0 bridge_flow_ratio = 0.8 bridge_speed = 20 brim_width = 0 clip_multipart_objects = 0 compatible_printers = "0.6mm - ABS";"0.6mm - PC" compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 elefant_foot_compensation = 0 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.6 external_perimeter_speed = 35 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.6 fill_angle = 45 fill_density = 60% fill_pattern = gyroid first_layer_acceleration = 0 first_layer_extrusion_width = 0.6 first_layer_height = 120% first_layer_speed = 50% gap_fill_speed = 35 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.6 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 0.1 infill_speed = 70 inherits = interface_shells = 0 layer_height = 0.3 max_print_speed = 300 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.6 perimeter_speed = 50 perimeters = 3 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 1 skirt_distance = 3 skirt_height = 1 skirts = 2 small_perimeter_speed = 25 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.6 solid_infill_speed = 70 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_auto = 1 support_material_buildplate_only = 1 support_material_contact_distance = 0.2 support_material_enforce_layers = 2 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 35 support_material_synchronize_layers = 0 support_material_threshold = 60 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 0 threads = 16 top_infill_extrusion_width = 0.6 top_solid_infill_speed = 35 top_solid_layers = 6 travel_speed = 300 wipe_tower = 0 wipe_tower_bridging = 10 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 [print:0.6+0.3 - VP] avoid_crossing_perimeters = 0 bottom_solid_layers = 6 bridge_acceleration = 0 bridge_angle = 0 bridge_flow_ratio = 0.8 bridge_speed = 20 brim_width = 0 clip_multipart_objects = 0 compatible_printers = "0.6mm - ABS";"0.6mm - PC" compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 elefant_foot_compensation = 0 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.6 external_perimeter_speed = 50 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.6 fill_angle = 45 fill_density = 60% fill_pattern = gyroid first_layer_acceleration = 0 first_layer_extrusion_width = 0.6 first_layer_height = 120% first_layer_speed = 50% gap_fill_speed = 40 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.6 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 0.1 infill_speed = 100 inherits = interface_shells = 0 layer_height = 0.3 max_print_speed = 300 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.6 perimeter_speed = 50 perimeters = 3 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 1 skirt_distance = 3 skirt_height = 1 skirts = 2 small_perimeter_speed = 25 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.6 solid_infill_speed = 100 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_auto = 1 support_material_buildplate_only = 1 support_material_contact_distance = 0.2 support_material_enforce_layers = 2 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 50 support_material_synchronize_layers = 0 support_material_threshold = 60 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 0 threads = 16 top_infill_extrusion_width = 0.6 top_solid_infill_speed = 50 top_solid_layers = 6 travel_speed = 300 wipe_tower = 0 wipe_tower_bridging = 10 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 [print:0.8+0.2] avoid_crossing_perimeters = 0 bottom_solid_layers = 8 bridge_acceleration = 0 bridge_angle = 0 bridge_flow_ratio = 0.8 bridge_speed = 20 brim_width = 0 clip_multipart_objects = 0 compatible_printers = "0.8mm - ABS";"0.8mm - PC" compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 elefant_foot_compensation = 0 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.8 external_perimeter_speed = 35 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.8 fill_angle = 45 fill_density = 60% fill_pattern = gyroid first_layer_acceleration = 0 first_layer_extrusion_width = 0.8 first_layer_height = 120% first_layer_speed = 30 gap_fill_speed = 35 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.8 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 0.1 infill_speed = 80 inherits = interface_shells = 0 layer_height = 0.2 max_print_speed = 300 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.8 perimeter_speed = 50 perimeters = 2 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 1 skirt_distance = 3 skirt_height = 1 skirts = 2 small_perimeter_speed = 25 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.8 solid_infill_speed = 80 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_auto = 1 support_material_buildplate_only = 1 support_material_contact_distance = 0.2 support_material_enforce_layers = 2 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 35 support_material_synchronize_layers = 0 support_material_threshold = 60 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 0 threads = 16 top_infill_extrusion_width = 0.8 top_solid_infill_speed = 40 top_solid_layers = 8 travel_speed = 300 wipe_tower = 0 wipe_tower_bridging = 10 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 [print:0.8+0.4] avoid_crossing_perimeters = 0 bottom_solid_layers = 4 bridge_acceleration = 0 bridge_angle = 0 bridge_flow_ratio = 0.8 bridge_speed = 20 brim_width = 0 clip_multipart_objects = 0 compatible_printers = "0.8mm - ABS";"0.8mm - PC" compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 elefant_foot_compensation = 0 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.8 external_perimeter_speed = 35 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.8 fill_angle = 45 fill_density = 30% fill_pattern = gyroid first_layer_acceleration = 0 first_layer_extrusion_width = 0.8 first_layer_height = 100% first_layer_speed = 30 gap_fill_speed = 35 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.8 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 0.1 infill_speed = 80 inherits = interface_shells = 0 layer_height = 0.4 max_print_speed = 300 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.8 perimeter_speed = 50 perimeters = 2 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 1 skirt_distance = 3 skirt_height = 1 skirts = 2 small_perimeter_speed = 25 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.8 solid_infill_speed = 80 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_auto = 1 support_material_buildplate_only = 1 support_material_contact_distance = 0.2 support_material_enforce_layers = 2 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 35 support_material_synchronize_layers = 0 support_material_threshold = 60 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 0 threads = 16 top_infill_extrusion_width = 0.8 top_solid_infill_speed = 40 top_solid_layers = 4 travel_speed = 300 wipe_tower = 0 wipe_tower_bridging = 10 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 [print:0.8+0.4 - HOLLOW PARTS] avoid_crossing_perimeters = 0 bottom_solid_layers = 4 bridge_acceleration = 0 bridge_angle = 0 bridge_flow_ratio = 0.8 bridge_speed = 20 brim_width = 0 clip_multipart_objects = 0 compatible_printers = "0.8mm - ABS";"0.8mm - PC" compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 elefant_foot_compensation = 0 ensure_vertical_shell_thickness = 0 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.8 external_perimeter_speed = 35 external_perimeters_first = 0 extra_perimeters = 0 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.8 fill_angle = 45 fill_density = 0% fill_pattern = gyroid first_layer_acceleration = 0 first_layer_extrusion_width = 0.8 first_layer_height = 100% first_layer_speed = 30 gap_fill_speed = 35 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.8 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 0.1 infill_speed = 80 inherits = interface_shells = 0 layer_height = 0.4 max_print_speed = 300 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.8 perimeter_speed = 50 perimeters = 2 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 1 skirt_distance = 3 skirt_height = 1 skirts = 2 small_perimeter_speed = 25 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.8 solid_infill_speed = 80 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_auto = 1 support_material_buildplate_only = 1 support_material_contact_distance = 0.2 support_material_enforce_layers = 2 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 35 support_material_synchronize_layers = 0 support_material_threshold = 60 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 0 threads = 16 top_infill_extrusion_width = 0.8 top_solid_infill_speed = 40 top_solid_layers = 4 travel_speed = 300 wipe_tower = 0 wipe_tower_bridging = 10 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 [print:V320 0.2mm Layer Height - Chains] avoid_crossing_perimeters = 0 bottom_solid_layers = 5 bridge_acceleration = 0 bridge_angle = 0 bridge_flow_ratio = 0.8 bridge_speed = 20 brim_width = 0 clip_multipart_objects = 0 compatible_printers = compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 elefant_foot_compensation = 0 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.4 external_perimeter_speed = 50 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.4 fill_angle = 45 fill_density = 40% fill_pattern = cubic first_layer_acceleration = 0 first_layer_extrusion_width = 0.4 first_layer_height = 120% first_layer_speed = 30 gap_fill_speed = 40 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.4 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 100 inherits = interface_shells = 0 layer_height = 0.2 max_print_speed = 300 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = V320-[input_filename_base].gcode overhangs = 0 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.4 perimeter_speed = 70 perimeters = 3 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 1 skirt_distance = 3 skirt_height = 1 skirts = 3 small_perimeter_speed = 50 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.4 solid_infill_speed = 100 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_auto = 1 support_material_buildplate_only = 1 support_material_contact_distance = 0.2 support_material_enforce_layers = 2 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 50 support_material_synchronize_layers = 0 support_material_threshold = 60 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 0 threads = 16 top_infill_extrusion_width = 0.4 top_solid_infill_speed = 50 top_solid_layers = 5 travel_speed = 300 wipe_tower = 0 wipe_tower_bridging = 10 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 [print:V320 0.2mm Layer Height - VORON PARTS] avoid_crossing_perimeters = 0 bottom_solid_layers = 5 bridge_acceleration = 0 bridge_angle = 0 bridge_flow_ratio = 0.8 bridge_speed = 20 brim_width = 0 clip_multipart_objects = 0 compatible_printers = compatible_printers_condition = complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 elefant_foot_compensation = 0 ensure_vertical_shell_thickness = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.4 external_perimeter_speed = 50 external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.4 fill_angle = 45 fill_density = 40% fill_pattern = cubic first_layer_acceleration = 0 first_layer_extrusion_width = 0.4 first_layer_height = 120% first_layer_speed = 25 gap_fill_speed = 35 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.4 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 25% infill_speed = 100 inherits = interface_shells = 0 layer_height = 0.2 max_print_speed = 300 max_volumetric_extrusion_rate_slope_negative = 0 max_volumetric_extrusion_rate_slope_positive = 0 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = V320-[input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.4 perimeter_speed = 70 perimeters = 4 post_process = print_settings_id = raft_layers = 0 resolution = 0 seam_position = aligned single_extruder_multi_material_priming = 1 skirt_distance = 3 skirt_height = 1 skirts = 3 small_perimeter_speed = 30 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.4 solid_infill_speed = 100 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_auto = 1 support_material_buildplate_only = 1 support_material_contact_distance = 0.2 support_material_enforce_layers = 2 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = rectilinear support_material_spacing = 2.5 support_material_speed = 50 support_material_synchronize_layers = 0 support_material_threshold = 60 support_material_with_sheath = 1 support_material_xy_spacing = 50% thin_walls = 1 threads = 16 top_infill_extrusion_width = 0.4 top_solid_infill_speed = 50 top_solid_layers = 5 travel_speed = 300 wipe_tower = 0 wipe_tower_bridging = 10 wipe_tower_rotation_angle = 0 wipe_tower_width = 60 wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 [filament:ABS+] bed_temperature = 95 bridge_fan_speed = 10 compatible_printers = compatible_printers_condition = cooling = 0 disable_fan_first_layers = 5 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.97 fan_always_on = 1 fan_below_layer_time = 30 filament_colour = #000000 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 11 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = ABS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 100 first_layer_temperature = 235 inherits = max_fan_speed = 20 min_fan_speed = 5 min_print_speed = 15 slowdown_below_layer_time = 1 start_filament_gcode = "; Filament gcode\n; M572 D0 S0.1 ;Pressure Advance" temperature = 235 [filament:ABS-Ziro] bed_temperature = 105 bridge_fan_speed = 50 compatible_printers = compatible_printers_condition = cooling = 1 disable_fan_first_layers = 10 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.91 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FF8000 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 11 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = ABS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 110 first_layer_temperature = 240 inherits = max_fan_speed = 0 min_fan_speed = 0 min_print_speed = 15 slowdown_below_layer_time = 60 start_filament_gcode = "; Filament gcode\nM572 D0 S0.1 ;Pressure Advance" temperature = 240 [filament:Paramount ABS] bed_temperature = 100 bridge_fan_speed = 20 compatible_printers = compatible_printers_condition = cooling = 0 disable_fan_first_layers = 5 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.92 fan_always_on = 1 fan_below_layer_time = 45 filament_colour = #000000 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 11 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = ABS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 105 first_layer_temperature = 245 inherits = max_fan_speed = 20 min_fan_speed = 5 min_print_speed = 15 slowdown_below_layer_time = 1 start_filament_gcode = "; Filament gcode\n; M572 D0 S0.1 ;Pressure Advance" temperature = 240 [filament:V6 - ABS - BN] bed_temperature = 100 bridge_fan_speed = 50 compatible_printers = compatible_printers_condition = cooling = 1 disable_fan_first_layers = 4 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.92 fan_always_on = 0 fan_below_layer_time = 45 filament_colour = #00FF80 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 11 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = ABS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 100 first_layer_temperature = 235 inherits = max_fan_speed = 20 min_fan_speed = 0 min_print_speed = 10 slowdown_below_layer_time = 45 start_filament_gcode = ";Filament gcode" temperature = 235 [filament:V6 - ABS - SN] bed_temperature = 100 bridge_fan_speed = 50 compatible_printers = "0.4mm - ABS";"0.6mm - ABS" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 4 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.92 fan_always_on = 0 fan_below_layer_time = 45 filament_colour = #00FF80 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 11 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = ABS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 100 first_layer_temperature = 245 inherits = max_fan_speed = 20 min_fan_speed = 0 min_print_speed = 10 slowdown_below_layer_time = 45 start_filament_gcode = "; Filament gcode" temperature = 245 [filament:V6 - ABS - SN - EXTRA COOLING] bed_temperature = 100 bridge_fan_speed = 50 compatible_printers = "0.4mm - ABS";"0.6mm - ABS" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 4 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.92 fan_always_on = 0 fan_below_layer_time = 45 filament_colour = #00FF80 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 11 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = ABS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 100 first_layer_temperature = 245 inherits = max_fan_speed = 45 min_fan_speed = 0 min_print_speed = 10 slowdown_below_layer_time = 45 start_filament_gcode = "; Filament gcode" temperature = 245 [filament:V6 - PETG - BN] bed_temperature = 75 bridge_fan_speed = 50 compatible_printers = "0.4mm - PETG" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 3 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.925 fan_always_on = 1 fan_below_layer_time = 20 filament_colour = #FF0000 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 10 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = PET filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 80 first_layer_temperature = 237 inherits = max_fan_speed = 50 min_fan_speed = 30 min_print_speed = 5 slowdown_below_layer_time = 10 start_filament_gcode = ";Filament gcode" temperature = 235 [filament:V6 - PETG - SN] bed_temperature = 75 bridge_fan_speed = 50 compatible_printers = "0.4mm - PETG" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 3 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.925 fan_always_on = 1 fan_below_layer_time = 20 filament_colour = #FF0000 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 10 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = PET filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 80 first_layer_temperature = 247 inherits = max_fan_speed = 50 min_fan_speed = 30 min_print_speed = 5 slowdown_below_layer_time = 10 start_filament_gcode = ";Filament gcode" temperature = 240 [filament:V6 - PLA - BN] bed_temperature = 65 bridge_fan_speed = 100 compatible_printers = "0.4mm - PLA" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 1 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 100 filament_colour = #0080FF filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 15 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = PLA filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 70 first_layer_temperature = 215 inherits = max_fan_speed = 100 min_fan_speed = 85 min_print_speed = 15 slowdown_below_layer_time = 10 start_filament_gcode = ";Filament gcode" temperature = 210 [filament:V6 - PLA - SN] bed_temperature = 65 bridge_fan_speed = 100 compatible_printers = "0.4mm - PLA" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 1 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 100 filament_colour = #0080FF filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 15 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = PLA filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 70 first_layer_temperature = 220 inherits = max_fan_speed = 100 min_fan_speed = 85 min_print_speed = 15 slowdown_below_layer_time = 10 start_filament_gcode = ";Filament gcode" temperature = 215 [filament:V6 - Priline PC - BN] bed_temperature = 100 bridge_fan_speed = 40 compatible_printers = "0.4mm - PC";"0.6mm - PC" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 4 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 0 filament_colour = #8000FF filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 50 filament_density = 1.22 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 11 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = PC filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 100 first_layer_temperature = 270 inherits = max_fan_speed = 0 min_fan_speed = 0 min_print_speed = 15 slowdown_below_layer_time = 60 start_filament_gcode = ";Filament gcode" temperature = 270 [filament:V6 - Priline PC - SN] bed_temperature = 100 bridge_fan_speed = 40 compatible_printers = "0.4mm - PC";"0.6mm - PC" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 4 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 0 filament_colour = #8000FF filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 50 filament_density = 1.22 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 11 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = PC filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 100 first_layer_temperature = 275 inherits = max_fan_speed = 0 min_fan_speed = 0 min_print_speed = 15 slowdown_below_layer_time = 60 start_filament_gcode = ";Filament gcode" temperature = 275 [filament:VOLCANO - ABS - BN] bed_temperature = 100 bridge_fan_speed = 50 compatible_printers = "0.4mm - ABS";"0.6mm - ABS";"0.8mm - ABS" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 4 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.92 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #00FF80 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 30 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = ABS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 100 first_layer_temperature = 235 inherits = max_fan_speed = 20 min_fan_speed = 0 min_print_speed = 10 slowdown_below_layer_time = 45 start_filament_gcode = ";Filament gcode" temperature = 235 [filament:VOLCANO - ABS - SN] bed_temperature = 100 bridge_fan_speed = 50 compatible_printers = "0.4mm - ABS";"0.6mm - ABS";"0.8mm - ABS" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 4 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.92 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #00FF80 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 30 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = ABS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 100 first_layer_temperature = 245 inherits = max_fan_speed = 20 min_fan_speed = 0 min_print_speed = 10 slowdown_below_layer_time = 45 start_filament_gcode = "; Filament gcode" temperature = 245 [filament:VOLCANO - ABS - SN - EXTRA COOLING] bed_temperature = 100 bridge_fan_speed = 50 compatible_printers = "0.4mm - ABS";"0.6mm - ABS";"0.8mm - ABS" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 4 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.92 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #00FF80 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 30 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = ABS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 100 first_layer_temperature = 245 inherits = max_fan_speed = 45 min_fan_speed = 0 min_print_speed = 10 slowdown_below_layer_time = 45 start_filament_gcode = "; Filament gcode" temperature = 245 [filament:VOLCANO - Priline PC - BN] bed_temperature = 100 bridge_fan_speed = 40 compatible_printers = "0.4mm - PC";"0.6mm - PC";"0.8mm - PC" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 4 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 0 filament_colour = #8000FF filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 50 filament_density = 1.22 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 30 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = PC filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 100 first_layer_temperature = 270 inherits = max_fan_speed = 0 min_fan_speed = 0 min_print_speed = 15 slowdown_below_layer_time = 60 start_filament_gcode = ";Filament gcode" temperature = 270 [filament:VOLCANO - Priline PC - SN] bed_temperature = 100 bridge_fan_speed = 40 compatible_printers = "0.4mm - PC";"0.6mm - PC";"0.8mm - PC" compatible_printers_condition = cooling = 1 disable_fan_first_layers = 4 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 0 filament_colour = #8000FF filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 50 filament_density = 1.22 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 30 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = PC filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 100 first_layer_temperature = 275 inherits = max_fan_speed = 0 min_fan_speed = 0 min_print_speed = 15 slowdown_below_layer_time = 60 start_filament_gcode = ";Filament gcode" temperature = 275 [filament:Veracity ABS] bed_temperature = 105 bridge_fan_speed = 40 compatible_printers = compatible_printers_condition = cooling = 1 disable_fan_first_layers = 5 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" extrusion_multiplier = 0.92 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #000000 filament_cooling_final_speed = 3.4 filament_cooling_initial_speed = 2.2 filament_cooling_moves = 4 filament_cost = 30 filament_density = 1.25 filament_diameter = 1.75 filament_load_time = 0 filament_loading_speed = 28 filament_loading_speed_start = 3 filament_max_volumetric_speed = 11 filament_minimal_purge_on_wipe_tower = 15 filament_notes = "" filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" filament_settings_id = "" filament_soluble = 0 filament_toolchange_delay = 0 filament_type = ABS filament_unload_time = 0 filament_unloading_speed = 90 filament_unloading_speed_start = 100 first_layer_bed_temperature = 105 first_layer_temperature = 250 inherits = max_fan_speed = 40 min_fan_speed = 10 min_print_speed = 15 slowdown_below_layer_time = 60 start_filament_gcode = "; Filament gcode\n; M572 D0 S0.1 ;Pressure Advance" temperature = 250 [printer:0.4mm - ABS] bed_shape = 0x0,320x0,320x320,0x320 before_layer_gcode = between_objects_gcode = cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = default_print_profile = deretract_speed = 30 end_gcode = M98 P"print_end.g" extra_loading_move = -2 extruder_colour = #00FF00 extruder_offset = 0x0 gcode_flavor = reprap host_type = octoprint inherits = layer_gcode = machine_max_acceleration_e = 10000,5000 machine_max_acceleration_extruding = 1500,1250 machine_max_acceleration_retracting = 1500,1250 machine_max_acceleration_x = 9000,1000 machine_max_acceleration_y = 9000,1000 machine_max_acceleration_z = 500,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,200 machine_max_feedrate_y = 500,200 machine_max_feedrate_z = 12,12 machine_max_jerk_e = 2.5,2.5 machine_max_jerk_x = 10,10 machine_max_jerk_y = 10,10 machine_max_jerk_z = 0.2,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.3 max_print_height = 300 min_layer_height = 0.07 nozzle_diameter = 0.4 parking_pos_retraction = 92 print_host = printer_model = printer_notes = printer_settings_id = printer_variant = printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 3 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 6.5 retract_length_toolchange = 10 retract_lift = 0.4 retract_lift_above = 0 retract_lift_below = 300 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 80 serial_port = serial_speed = 250000 silent_mode = 1 single_extruder_multi_material = 0 start_gcode = T0\nM104 S0 ;cancel S3D set temp\nG21 ; set units to mm\nG90 ; use absolute coordinates\nT0 ; select tool 0\nG92 E0.0 ; reset e count\nM220 S100 ; reset speed multiplier\nM140 S[first_layer_bed_temperature] ; set bed temperature and do not wait\nM104 S[temperature_0] ; set print head temperature and do not wait\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\n\nG32; home all and adjust gantry compensation\n\nM109 S[temperature_0] ; set print head temperature and wait\n; === pause for heating ===\nG1 E2 F200 ; prime extruder\nG92 E0.0 ; reset e count toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 0 z_offset = 0 [printer:0.4mm - PC] bed_shape = 0x0,350x0,350x350,0x350 before_layer_gcode = between_objects_gcode = cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = default_print_profile = deretract_speed = 30 end_gcode = print_end ;end script from macro extra_loading_move = -2 extruder_colour = #8000FF extruder_offset = 0x0 gcode_flavor = reprap host_type = octoprint inherits = layer_gcode = machine_max_acceleration_e = 10000,5000 machine_max_acceleration_extruding = 1500,1250 machine_max_acceleration_retracting = 1500,1250 machine_max_acceleration_x = 9000,1000 machine_max_acceleration_y = 9000,1000 machine_max_acceleration_z = 500,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,200 machine_max_feedrate_y = 500,200 machine_max_feedrate_z = 12,12 machine_max_jerk_e = 2.5,2.5 machine_max_jerk_x = 10,10 machine_max_jerk_y = 10,10 machine_max_jerk_z = 0.2,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.3 max_print_height = 325 min_layer_height = 0.07 nozzle_diameter = 0.4 parking_pos_retraction = 92 print_host = printer_model = printer_notes = printer_settings_id = printer_variant = printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 3 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 6.5 retract_length_toolchange = 10 retract_lift = 0.4 retract_lift_above = 0 retract_lift_below = 300 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 80 serial_port = serial_speed = 250000 silent_mode = 1 single_extruder_multi_material = 0 start_gcode = print_start_1 ;start script from macro portion 1\n\nM140 S[first_layer_bed_temperature] ; set bed temperature and do not wait\nM109 S190 ; set print head temperature and wait\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\n\nprint_start_2 ;start script from macro portion 2\n\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\nM109 S[first_layer_temperature] ; set print head temperature and wait\n\nprint_start_3 ;start script from macro portion 3\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 1 z_offset = 0 [printer:0.4mm - PETG] bed_shape = 0x0,350x0,350x350,0x350 before_layer_gcode = between_objects_gcode = cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = default_print_profile = deretract_speed = 30 end_gcode = print_end ;end script from macro extra_loading_move = -2 extruder_colour = #FF8040 extruder_offset = 0x0 gcode_flavor = reprap host_type = octoprint inherits = layer_gcode = machine_max_acceleration_e = 10000,5000 machine_max_acceleration_extruding = 1500,1250 machine_max_acceleration_retracting = 1500,1250 machine_max_acceleration_x = 9000,1000 machine_max_acceleration_y = 9000,1000 machine_max_acceleration_z = 500,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,200 machine_max_feedrate_y = 500,200 machine_max_feedrate_z = 12,12 machine_max_jerk_e = 2.5,2.5 machine_max_jerk_x = 10,10 machine_max_jerk_y = 10,10 machine_max_jerk_z = 0.2,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.3 max_print_height = 325 min_layer_height = 0.07 nozzle_diameter = 0.4 parking_pos_retraction = 92 print_host = printer_model = printer_notes = printer_settings_id = printer_variant = printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 3 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 7.5 retract_length_toolchange = 10 retract_lift = 0.4 retract_lift_above = 0 retract_lift_below = 300 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 80 serial_port = serial_speed = 250000 silent_mode = 1 single_extruder_multi_material = 0 start_gcode = print_start_1 ;start script from macro portion 1\n\nM140 S[first_layer_bed_temperature] ; set bed temperature and do not wait\nM109 S190 ; set print head temperature and wait\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\n\nprint_start_2 ;start script from macro portion 2\n\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\nM109 S[first_layer_temperature] ; set print head temperature and wait\n\nprint_start_3 ;start script from macro portion 3 toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 1 z_offset = 0 [printer:0.4mm - PLA] bed_shape = 0x0,350x0,350x350,0x350 before_layer_gcode = between_objects_gcode = cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = default_print_profile = deretract_speed = 30 end_gcode = print_end ;end script from macro extra_loading_move = -2 extruder_colour = #FF0000 extruder_offset = 0x0 gcode_flavor = reprap host_type = octoprint inherits = layer_gcode = machine_max_acceleration_e = 10000,5000 machine_max_acceleration_extruding = 1500,1250 machine_max_acceleration_retracting = 1500,1250 machine_max_acceleration_x = 9000,1000 machine_max_acceleration_y = 9000,1000 machine_max_acceleration_z = 500,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,200 machine_max_feedrate_y = 500,200 machine_max_feedrate_z = 12,12 machine_max_jerk_e = 2.5,2.5 machine_max_jerk_x = 10,10 machine_max_jerk_y = 10,10 machine_max_jerk_z = 0.2,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.3 max_print_height = 325 min_layer_height = 0.07 nozzle_diameter = 0.4 parking_pos_retraction = 92 print_host = printer_model = printer_notes = printer_settings_id = printer_variant = printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 3 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 6.5 retract_length_toolchange = 10 retract_lift = 0.4 retract_lift_above = 0 retract_lift_below = 300 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 80 serial_port = serial_speed = 250000 silent_mode = 1 single_extruder_multi_material = 0 start_gcode = print_start_1 ;start script from macro portion 1\n\nM140 S[first_layer_bed_temperature] ; set bed temperature and do not wait\nM109 S190 ; set print head temperature and wait\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\n\nprint_start_2 ;start script from macro portion 2\n\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\nM109 S[first_layer_temperature] ; set print head temperature and wait\n\nprint_start_3 ;start script from macro portion 3 toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 1 z_offset = 0 [printer:0.6mm - ABS] bed_shape = 0x0,350x0,350x350,0x350 before_layer_gcode = between_objects_gcode = cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = default_print_profile = deretract_speed = 30 end_gcode = print_end ;end script from macro extra_loading_move = -2 extruder_colour = #00FF00 extruder_offset = 0x0 gcode_flavor = reprap host_type = octoprint inherits = layer_gcode = machine_max_acceleration_e = 10000,5000 machine_max_acceleration_extruding = 1500,1250 machine_max_acceleration_retracting = 1500,1250 machine_max_acceleration_x = 9000,1000 machine_max_acceleration_y = 9000,1000 machine_max_acceleration_z = 500,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,200 machine_max_feedrate_y = 500,200 machine_max_feedrate_z = 12,12 machine_max_jerk_e = 2.5,2.5 machine_max_jerk_x = 10,10 machine_max_jerk_y = 10,10 machine_max_jerk_z = 0.2,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.45 max_print_height = 325 min_layer_height = 0.15 nozzle_diameter = 0.6 parking_pos_retraction = 92 print_host = printer_model = printer_notes = printer_settings_id = printer_variant = printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 3 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 6.5 retract_length_toolchange = 10 retract_lift = 0.4 retract_lift_above = 0 retract_lift_below = 300 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 80 serial_port = serial_speed = 250000 silent_mode = 1 single_extruder_multi_material = 0 start_gcode = print_start_1 ;start script from macro portion 1\n\nM140 S[first_layer_bed_temperature] ; set bed temperature and do not wait\nM109 S190 ; set print head temperature and wait\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\n\nprint_start_2 ;start script from macro portion 2\n\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\nM109 S[first_layer_temperature] ; set print head temperature and wait\n\nprint_start_3 ;start script from macro portion 3 toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 1 z_offset = 0 [printer:0.6mm - PC] bed_shape = 0x0,350x0,350x350,0x350 before_layer_gcode = between_objects_gcode = cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = default_print_profile = deretract_speed = 30 end_gcode = print_end ;end script from macro extra_loading_move = -2 extruder_colour = #8000FF extruder_offset = 0x0 gcode_flavor = reprap host_type = octoprint inherits = layer_gcode = machine_max_acceleration_e = 10000,5000 machine_max_acceleration_extruding = 1500,1250 machine_max_acceleration_retracting = 1500,1250 machine_max_acceleration_x = 9000,1000 machine_max_acceleration_y = 9000,1000 machine_max_acceleration_z = 500,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,200 machine_max_feedrate_y = 500,200 machine_max_feedrate_z = 12,12 machine_max_jerk_e = 2.5,2.5 machine_max_jerk_x = 10,10 machine_max_jerk_y = 10,10 machine_max_jerk_z = 0.2,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.45 max_print_height = 325 min_layer_height = 0.15 nozzle_diameter = 0.6 parking_pos_retraction = 92 print_host = printer_model = printer_notes = printer_settings_id = printer_variant = printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 3 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 6.5 retract_length_toolchange = 10 retract_lift = 0.4 retract_lift_above = 0 retract_lift_below = 300 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 80 serial_port = serial_speed = 250000 silent_mode = 1 single_extruder_multi_material = 0 start_gcode = print_start_1 ;start script from macro portion 1\n\nM140 S[first_layer_bed_temperature] ; set bed temperature and do not wait\nM109 S190 ; set print head temperature and wait\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\n\nprint_start_2 ;start script from macro portion 2\n\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\nM109 S[first_layer_temperature] ; set print head temperature and wait\n\nprint_start_3 ;start script from macro portion 3 toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 1 z_offset = 0 [printer:0.8mm - ABS] bed_shape = 0x0,350x0,350x350,0x350 before_layer_gcode = between_objects_gcode = cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = default_print_profile = deretract_speed = 30 end_gcode = print_end ;end script from macro extra_loading_move = -2 extruder_colour = #00FF00 extruder_offset = 0x0 gcode_flavor = reprap host_type = octoprint inherits = layer_gcode = machine_max_acceleration_e = 10000,5000 machine_max_acceleration_extruding = 1500,1250 machine_max_acceleration_retracting = 1500,1250 machine_max_acceleration_x = 9000,1000 machine_max_acceleration_y = 9000,1000 machine_max_acceleration_z = 500,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,200 machine_max_feedrate_y = 500,200 machine_max_feedrate_z = 12,12 machine_max_jerk_e = 2.5,2.5 machine_max_jerk_x = 10,10 machine_max_jerk_y = 10,10 machine_max_jerk_z = 0.2,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.6 max_print_height = 325 min_layer_height = 0.2 nozzle_diameter = 0.8 parking_pos_retraction = 92 print_host = printer_model = printer_notes = printer_settings_id = printer_variant = printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 10 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 6.5 retract_length_toolchange = 10 retract_lift = 0.4 retract_lift_above = 0 retract_lift_below = 300 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 80 serial_port = serial_speed = 250000 silent_mode = 1 single_extruder_multi_material = 0 start_gcode = print_start_1 ;start script from macro portion 1\n\nM140 S[first_layer_bed_temperature] ; set bed temperature and do not wait\nM109 S190 ; set print head temperature and wait\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\n\nprint_start_2 ;start script from macro portion 2\n\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\nM109 S[first_layer_temperature] ; set print head temperature and wait\n\nprint_start_3 ;start script from macro portion 3 toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 1 z_offset = 0 [printer:0.8mm - PC] bed_shape = 0x0,350x0,350x350,0x350 before_layer_gcode = between_objects_gcode = cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = default_print_profile = deretract_speed = 30 end_gcode = print_end ;end script from macro extra_loading_move = -2 extruder_colour = #8000FF extruder_offset = 0x0 gcode_flavor = reprap host_type = octoprint inherits = layer_gcode = machine_max_acceleration_e = 10000,5000 machine_max_acceleration_extruding = 1500,1250 machine_max_acceleration_retracting = 1500,1250 machine_max_acceleration_x = 9000,1000 machine_max_acceleration_y = 9000,1000 machine_max_acceleration_z = 500,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,200 machine_max_feedrate_y = 500,200 machine_max_feedrate_z = 12,12 machine_max_jerk_e = 2.5,2.5 machine_max_jerk_x = 10,10 machine_max_jerk_y = 10,10 machine_max_jerk_z = 0.2,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.6 max_print_height = 325 min_layer_height = 0.2 nozzle_diameter = 0.8 parking_pos_retraction = 92 print_host = printer_model = printer_notes = printer_settings_id = printer_variant = printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 10 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 6.56 retract_length_toolchange = 10 retract_lift = 0.4 retract_lift_above = 0 retract_lift_below = 300 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 80 serial_port = serial_speed = 250000 silent_mode = 1 single_extruder_multi_material = 0 start_gcode = print_start_1 ;start script from macro portion 1\n\nM140 S[first_layer_bed_temperature] ; set bed temperature and do not wait\nM109 S190 ; set print head temperature and wait\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\n\nprint_start_2 ;start script from macro portion 2\n\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\nM109 S[first_layer_temperature] ; set print head temperature and wait\n\nprint_start_3 ;start script from macro portion 3 toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 1 z_offset = 0 [printer:V320 Setting Testing] bed_shape = 0x0,320x0,320x320,0x320 before_layer_gcode = between_objects_gcode = cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = default_print_profile = deretract_speed = 30 end_gcode = M98 P"print_end.g" extra_loading_move = -2 extruder_colour = #00FF00 extruder_offset = 0x0 gcode_flavor = reprap host_type = octoprint inherits = layer_gcode = machine_max_acceleration_e = 10000,5000 machine_max_acceleration_extruding = 1500,1250 machine_max_acceleration_retracting = 1500,1250 machine_max_acceleration_x = 9000,1000 machine_max_acceleration_y = 9000,1000 machine_max_acceleration_z = 500,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,200 machine_max_feedrate_y = 500,200 machine_max_feedrate_z = 12,12 machine_max_jerk_e = 2.5,2.5 machine_max_jerk_x = 10,10 machine_max_jerk_y = 10,10 machine_max_jerk_z = 0.2,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.3 max_print_height = 300 min_layer_height = 0.07 nozzle_diameter = 0.4 parking_pos_retraction = 92 print_host = printer_model = printer_notes = printer_settings_id = printer_variant = printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 3 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 6.5 retract_length_toolchange = 10 retract_lift = 0.4 retract_lift_above = 0 retract_lift_below = 300 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 80 serial_port = serial_speed = 250000 silent_mode = 1 single_extruder_multi_material = 0 start_gcode = T0\nM104 S0 ;cancel S3D set temp\nG21 ; set units to mm\nG90 ; use absolute coordinates\nT0 ; select tool 0\nG92 E0.0 ; reset e count\nM220 S100 ; reset speed multiplier\nM140 S[first_layer_bed_temperature] ; set bed temperature and do not wait\nM104 S[temperature_0] ; set print head temperature and do not wait\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\n\nG32; home all and adjust gantry compensation\n\nM109 S[temperature_0] ; set print head temperature and wait\n; === pause for heating ===\nG1 E2 F200 ; prime extruder\nG92 E0.0 ; reset e count\n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 0 z_offset = 0 [printer:V320 V2.1 - 0.4mm Nozzle - ABS ] bed_shape = 0x0,320x0,320x320,0x320 before_layer_gcode = between_objects_gcode = cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = default_print_profile = deretract_speed = 30 end_gcode = M98 P"print_end.g" extra_loading_move = -2 extruder_colour = #00FF00 extruder_offset = 0x0 gcode_flavor = reprap host_type = octoprint inherits = layer_gcode = ; pause as layer code\n; {if layer_z ==3.04}M226 ; pause at height for filament swap{endif}\n; {if layer_z ==3.64}M226 ; pause at height for filament swap{endif} machine_max_acceleration_e = 10000,5000 machine_max_acceleration_extruding = 1500,1250 machine_max_acceleration_retracting = 1500,1250 machine_max_acceleration_x = 9000,1000 machine_max_acceleration_y = 9000,1000 machine_max_acceleration_z = 500,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,200 machine_max_feedrate_y = 500,200 machine_max_feedrate_z = 12,12 machine_max_jerk_e = 2.5,2.5 machine_max_jerk_x = 10,10 machine_max_jerk_y = 10,10 machine_max_jerk_z = 0.2,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.3 max_print_height = 300 min_layer_height = 0.07 nozzle_diameter = 0.4 parking_pos_retraction = 92 print_host = printer_model = printer_notes = printer_settings_id = printer_variant = printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 3 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 5 retract_length_toolchange = 10 retract_lift = 0.6 retract_lift_above = 0 retract_lift_below = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 80 serial_port = serial_speed = 250000 silent_mode = 1 single_extruder_multi_material = 0 start_gcode = T0\nM104 S0 ;cancel S3D set temp\nG21 ; set units to mm\nG90 ; use absolute coordinates\nT0 ; select tool 0\nG92 E0.0 ; reset e count\nM220 S100 ; reset speed multiplier\nM140 S[first_layer_bed_temperature] ; set bed temperature and do not wait\nM104 S[temperature_0] ; set print head temperature and do not wait\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\n\nG32; home all and adjust gantry compensation\n\nM109 S[temperature_0] ; set print head temperature and wait\n; === pause for heating ===\nG1 E2 F200 ; prime extruder\nG92 E0.0 ; reset e count toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 1 z_offset = 0 [printer:VORON V2 - 0.4mm Nozzle - ABS - Slic3r_config_bundle] bed_shape = 0x0,250x0,250x250,0x250 before_layer_gcode = between_objects_gcode = cooling_tube_length = 5 cooling_tube_retraction = 91.5 default_filament_profile = default_print_profile = deretract_speed = 30 end_gcode = M98 P"print_end.g" extra_loading_move = -2 extruder_colour = #00FF00 extruder_offset = 0x0 gcode_flavor = reprap host_type = octoprint inherits = layer_gcode = ; pause as layer code\n; {if layer_z ==7.64}M226 ; pause at height for filament swap{endif}\n; {if layer_z ==10.84}M226 ; pause at height for filament swap{endif} machine_max_acceleration_e = 10000,5000 machine_max_acceleration_extruding = 1500,1250 machine_max_acceleration_retracting = 1500,1250 machine_max_acceleration_x = 9000,1000 machine_max_acceleration_y = 9000,1000 machine_max_acceleration_z = 500,200 machine_max_feedrate_e = 120,120 machine_max_feedrate_x = 500,200 machine_max_feedrate_y = 500,200 machine_max_feedrate_z = 12,12 machine_max_jerk_e = 2.5,2.5 machine_max_jerk_x = 10,10 machine_max_jerk_y = 10,10 machine_max_jerk_z = 0.2,0.4 machine_min_extruding_rate = 0,0 machine_min_travel_rate = 0,0 max_layer_height = 0.3 max_print_height = 250 min_layer_height = 0.07 nozzle_diameter = 0.4 parking_pos_retraction = 92 print_host = printer_model = printer_notes = printer_settings_id = printer_variant = printer_vendor = printhost_apikey = printhost_cafile = remaining_times = 0 retract_before_travel = 3 retract_before_wipe = 0% retract_layer_change = 0 retract_length = 5 retract_length_toolchange = 10 retract_lift = 0.6 retract_lift_above = 0 retract_lift_below = 300 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 80 serial_port = serial_speed = 250000 silent_mode = 1 single_extruder_multi_material = 0 start_gcode = T0\nM104 S0 ;cancel S3D set temp\nG21 ; set units to mm\nG90 ; use absolute coordinates\n\nT0 ; select tool 0\nG92 E0.0 ; reset e count\nM220 S100 ; reset speed multiplier\nM140 S[first_layer_bed_temperature] ; set bed temperature and do not wait\nM104 S[first_layer_temperature_0] ; set print head temperature and do not wait\nM190 S[first_layer_bed_temperature] ; set bed temperature and wait\n\nG32; home all and adjust gantry compensation\n\nM109 S[first_layer_temperature_0] ; set print head temperature and wait\n; === pause for heating ===\nG1 E2 F200 ; prime extruder\nG92 E0.0 ; reset e count toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 1 use_volumetric_e = 0 variable_layer_height = 1 wipe = 0 z_offset = 0 [presets] print = V320 0.2mm Layer Height - VORON PARTS printer = V320 V2.1 - 0.4mm Nozzle - ABS filament = Paramount ABS