From 157b9143d9a27f176a2cbf24780c4ebc7f221be9 Mon Sep 17 00:00:00 2001 From: Ben Eastep Date: Sun, 21 Mar 2021 20:51:41 -0600 Subject: [PATCH 1/7] renamed skr bracket for clarity --- ....3_bracket_x2.stl => skr_1.3_1.4_bracket_x2.stl} | Bin 1 file changed, 0 insertions(+), 0 deletions(-) rename STLs/VORON2.4/Electronics_Compartment/DIN_Brackets/{skr_1.3_bracket_x2.stl => skr_1.3_1.4_bracket_x2.stl} (100%) diff --git a/STLs/VORON2.4/Electronics_Compartment/DIN_Brackets/skr_1.3_bracket_x2.stl b/STLs/VORON2.4/Electronics_Compartment/DIN_Brackets/skr_1.3_1.4_bracket_x2.stl similarity index 100% rename from STLs/VORON2.4/Electronics_Compartment/DIN_Brackets/skr_1.3_bracket_x2.stl rename to STLs/VORON2.4/Electronics_Compartment/DIN_Brackets/skr_1.3_1.4_bracket_x2.stl From 83854dde5778c0e49d81d7c5f8f50d086275078f Mon Sep 17 00:00:00 2001 From: shiftingtech <53156353+shiftingtech@users.noreply.github.com> Date: Sun, 11 Jul 2021 17:13:27 -0600 Subject: [PATCH 2/7] Created draft config for V2 Spider --- .../Spider/Voron2_Spider_Config.cfg | 514 ++++++++++++++++++ 1 file changed, 514 insertions(+) create mode 100644 firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg diff --git a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg new file mode 100644 index 0000000..94048c0 --- /dev/null +++ b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg @@ -0,0 +1,514 @@ +## Voron Design VORON2 250/300/350mm Spider TMC2209 UART config + +## *** THINGS TO CHANGE/CHECK: *** +## MCU paths [mcu] section +## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file +## Z Endstop Switch location [safe_z_home] section +## Homing end position [gcode_macro G32] section +## Z Endstop Switch offset for Z0 [stepper_z] section +## Probe points [quad_gantry_level] section +## Min & Max gantry corner postions [quad_gantry_level] section +## PID tune [extruder] and [heater_bed] sections +## Fine tune E steps [extruder] section + +[mcu] +## Obtain definition by "ls -l /dev/serial/by-id/" +##-------------------------------------------------------------------- +serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_000000000000000000000000-if00 + +## Uncomment below if you're using the Raspberry uart0 to communicate with Spider +#restart_method: command + +[printer] +kinematics: corexy +max_velocity: 300 +max_accel: 3000 #Max 4000 +max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V +max_z_accel: 350 +square_corner_velocity: 5.0 + +##################################################################### +# X/Y Stepper Settings +##################################################################### + +[stepper_x] +## Connected to X-MOT (B Motor) +step_pin: PE11 +dir_pin: !PE10 +enable_pin: !PE9 +rotation_distance: 40 +microsteps: 16 +full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper +endstop_pin: ^PB14 +position_min: 0 + +##-------------------------------------------------------------------- + +## Uncomment below for 250mm build +#position_endstop: 250 +#position_max: 250 + +## Uncomment for 300mm build +#position_endstop: 300 +#position_max: 300 + +## Uncomment for 350mm build +#position_endstop: 350 +#position_max: 350 + +##-------------------------------------------------------------------- +homing_speed: 25 #Max 100 +homing_retract_dist: 5 +homing_positive_dir: true + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_x] +uart_pin: PE7 +interpolate: True +run_current: 0.8 +hold_current: 0.7 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +[stepper_y] +## Connected to Y-MOT (A Motor) +step_pin: PD8 +dir_pin: !PB12 +enable_pin: !PD9 +rotation_distance: 40 +microsteps: 16 +full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper +endstop_pin: ^PB13 +position_min: 0 +##-------------------------------------------------------------------- + +## Uncomment for 250mm build +#position_endstop: 250 +#position_max: 250 + +## Uncomment for 300mm build +#position_endstop: 300 +#position_max: 300 + +## Uncomment for 350mm build +#position_endstop: 350 +#position_max: 350 + +##-------------------------------------------------------------------- +homing_speed: 25 #Max 100 +homing_retract_dist: 5 +homing_positive_dir: true + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_y] +uart_pin: PE15 +interpolate: True +run_current: 0.8 +hold_current: 0.7 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +##################################################################### +# Z Stepper Settings +##################################################################### + +## In Z-MOT Position +## Z0 Stepper - Front Left +[stepper_z] +step_pin: PD14 +dir_pin: !PD13 +enable_pin: !PD15 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 16 +## In Z- Position +endstop_pin: ^PA0 +## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) +## (+) value = endstop above Z0, (-) value = endstop below +## Increasing position_endstop brings nozzle closer to the bed +## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config +position_endstop: -0.5 +##-------------------------------------------------------------------- + +## Uncomment below for 250mm build +#position_max: 240 + +## Uncomment below for 300mm build +#position_max: 290 + +## Uncomment below for 350mm build +#position_max: 340 + +##-------------------------------------------------------------------- +position_min: -5 +homing_speed: 8 +second_homing_speed: 3 +homing_retract_dist: 3 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z] +uart_pin: PD10 +uart_address: 0 +interpolate: True +run_current: 0.8 +hold_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## In E1-MOT Position +## Z1 Stepper - Rear Left +[stepper_z1] +step_pin: PE6 +dir_pin: PC13 +enable_pin: !PE5 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 16 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z1] +uart_pin: PC14 +interpolate: True +run_current: 0.8 +hold_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## In E2-MOT Position +## Z2 Stepper - Rear Right +[stepper_z2] +step_pin: PE2 +dir_pin: !PE4 +enable_pin: !PE3 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 16 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z2] +uart_pin: PC15 +interpolate: true +run_current: 0.8 +hold_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## In E3-MOT Position +## Z3 Stepper - Front Right +[stepper_z3] +step_pin: PD12 +dir_pin: PC4 +enable_pin: !PE8 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 16 + +[tmc2209 stepper_z3] +uart_pin: PA15 +interpolate: true +run_current: 0.8 +hold_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +##################################################################### +# Extruder +##################################################################### + +## In E0-MOT Position +[extruder] +step_pin: PD5 +dir_pin: !PD6 +enable_pin: !PD4 + +## Update value below when you perform extruder calibration +## If you ask for 100mm of filament, but in reality it is 98mm: +## rotation_distance = * / 100 +## 22.6789511 is a good starting point for Bondtech 5mm gears +## 34.37086 for Bondtech 8mm gears (Galileo) +rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears +## Update Gear Ratio depending on your Extruder Type +## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio) +## Use 80:20 for M4, M3.1 +## Use 7.5:1 for Galileo +gear_ratio: 50:17 #BMG Gear Ratio +microsteps: 16 +full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree +nozzle_diameter: 0.400 +filament_diameter: 1.75 +## In E0 OUT Position +heater_pin: PB15 +## Validate the following thermistor type to make sure it is correct +sensor_type: ATC Semitec 104GT-2 +sensor_pin: PC0 +min_temp: 10 +max_temp: 270 +max_power: 1.0 +min_extrude_temp: 170 +control = pid +pid_kp = 26.213 +pid_ki = 1.304 +pid_kd = 131.721 +## Try to keep pressure_advance below 1.0 +pressure_advance: 0.05 +## Default is 0.040, leave stock +pressure_advance_smooth_time: 0.040 + +## In E0-MOT Position +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 extruder] +uart_pin: PD7 +interpolate: false +run_current: 0.5 +hold_current: 0.4 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +##################################################################### +# Bed Heater +##################################################################### +[heater_bed] +## SSR Pin - In BED OUT position +heater_pin: PB4 +sensor_type: NTC 100K MGB18-104F39050L32 +sensor_pin: PC3 +## Adjust Max Power so your heater doesn't warp your bed +max_power: 0.6 +min_temp: 0 +max_temp: 120 +control: pid +pid_kp: 58.437 +pid_ki: 2.347 +pid_kd: 363.769 + +##################################################################### +# Probe +##################################################################### + +[probe] +## This probe is not used for Z height, only Quad Gantry Leveling +## In Z+ position +## If your probe is NO instead of NC, add change pin to ^PA3 +pin: ^!PA3 +x_offset: 0 +y_offset: 25.0 +z_offset: 0 +speed: 10.0 +samples: 3 +samples_result: median +sample_retract_dist: 3.0 +samples_tolerance: 0.006 +samples_tolerance_retries: 3 + +##################################################################### +# Fan Control +##################################################################### + +[heater_fan hotend_fan] +## Hotend Fan - FAN0 Connector +pin: PB0 +max_power: 1.0 +#kick_start_time: 0.5 +heater: extruder +heater_temp: 50.0 +## If you are experiencing back flow, you can reduce fan_speed +#fan_speed: 1.0 + +[fan] +## Print Cooling Fan - FAN1 Connector +pin: PB1 +max_power: 0.4 +#kick_start_time: 0.5 +## Depending on your fan, you may need to increase this value +## if your fan will not start. Can change cycle_time (increase) +## if your fan is not able to slow down effectively +off_below: 0.10 + +[heater_fan controller_fan] +## Controller fan - FAN2 Connector +pin: PB2 +#kick_start_time: 0.5 +heater: heater_bed +heater_temp: 45.0 + +#[heater_fan exhaust_fan] +## Exhaust fan - In E2 OUT Positon +#pin: PB3 +#max_power: 1.0 +#shutdown_speed: 0.0 +##kick_start_time: 0.5 +#heater: heater_bed +#heater_temp: 60 +#fan_speed: 1.0 + +##################################################################### +# LED Control +##################################################################### + +#[output_pin caselight ] +## Chamber Lighting - In E1 OUT Position +#pin: PC8 +#pwm: true +#shutdown_value: 0 +#cycle_time: 0.01 + +##################################################################### +# Homing and Gantry Adjustment Routines +##################################################################### + +[idle_timeout] +timeout: 1800 + +[safe_z_home] +## XY Location of the Z Endstop Switch +## Update -10,-10 to the XY coordinates of your endstop pin +## (such as 157,305) after going through Z Endstop Pin +## Location Definition step. +home_xy_position:-10,-10 +speed:100 +z_hop:10 + +[quad_gantry_level] +## Use QUAD_GANTRY_LEVEL to level a gantry. +## Min & Max gantry corners - measure from nozzle at MIN (0,0) and +## MAX (250, 250), (300,300), or (350,350) depending on your printer size +## to respective belt positions + +#-------------------------------------------------------------------- +## Gantry Corners for 250mm Build +## Uncomment for 250mm build +#gantry_corners: +# -60,-10 +# 310, 320 +## Probe points +#points: +# 50,25 +# 50,175 +# 200,175 +# 200,25 + +## Gantry Corners for 300mm Build +## Uncomment for 300mm build +#gantry_corners: +# -60,-10 +# 360,370 +## Probe points +#points: +# 50,25 +# 50,225 +# 250,225 +# 250,25 + +## Gantry Corners for 350mm Build +## Uncomment for 350mm build +#gantry_corners: +# -60,-10 +# 410,420 +## Probe points +#points: +# 50,25 +# 50,275 +# 300,275 +# 300,25 + +#-------------------------------------------------------------------- +speed: 100 +horizontal_move_z: 10 +retries: 5 +retry_tolerance: 0.0075 +max_adjust: 10 + +##################################################################### +# Displays +##################################################################### + +#-------------------------------------------------------------------- + +[display] +# mini12864 LCD Display +lcd_type: uc1701 +cs_pin: PC11 +a0_pin: PD2 +rst_pin: PC10 +encoder_pins: ^PC6,^PC7 +click_pin: ^!PA8 +contrast: 63 +#spi_bus: spi1 +spi_software_mosi_pin: PA7 +spi_software_miso_pin: PA6 +spi_software_sclk_pin: PA5 + +[neopixel fysetc_mini12864] +# To control Neopixel RGB in mini12864 display +pin: PC12 +chain_count: 3 +chain_count: 60 +initial_RED: 0.1 +initial_GREEN: 0.5 +initial_BLUE: 0.0 +color_order: RGB + +# Set RGB values on boot up for each Neopixel. +# Index 1 = display, Index 2 and 3 = Knob +[delayed_gcode setdisplayneopixel] +initial_duration: 1 +gcode: + SET_LED LED=fysetc_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 + SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 + SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 + +#-------------------------------------------------------------------- + + +##################################################################### +# Macros +##################################################################### + +[gcode_macro G32] +gcode: + BED_MESH_CLEAR + G28 + QUAD_GANTRY_LEVEL + G28 + ## Uncomment for for your size printer: + #-------------------------------------------------------------------- + ## Uncomment for 250mm build + #G0 X125 Y125 Z30 F3600 + + ## Uncomment for 300 build + #G0 X150 Y150 Z30 F3600 + + ## Uncomment for 350mm build + #G0 X175 Y175 Z30 F3600 + #-------------------------------------------------------------------- + +[gcode_macro PRINT_START] +# Use PRINT_START for the slicer starting script - please customise for your slicer of choice +gcode: + G32 ; home all axes + G1 Z20 F3000 ; move nozzle away from bed + +[gcode_macro PRINT_END] +# Use PRINT_END for the slicer ending script - please customise for your slicer of choice +gcode: + M400 ; wait for buffer to clear + G92 E0 ; zero the extruder + G1 E-10.0 F3600 ; retract filament + G91 ; relative positioning + G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing + TURN_OFF_HEATERS + M107 ; turn off fan + G1 Z2 F3000 ; move nozzle up 2mm + G90 ; absolute positioning + G0 X125 Y250 F3600 ; park nozzle at rear + BED_MESH_CLEAR + +## Thermistor Types +## "EPCOS 100K B57560G104F" +## "ATC Semitec 104GT-2" +## "NTC 100K beta 3950" +## "Honeywell 100K 135-104LAG-J01" +## "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad) +## "AD595" +## "PT100 INA826" +## "PT1000" From bdaeaee3a294f3821fc4fb5d3bcf7b93dc48270d Mon Sep 17 00:00:00 2001 From: shiftingtech <53156353+shiftingtech@users.noreply.github.com> Date: Thu, 12 Aug 2021 09:59:42 -0600 Subject: [PATCH 3/7] endstop fix updated X & Y Endstops to match wiring diagram --- .../klipper_configurations/Spider/Voron2_Spider_Config.cfg | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg index 94048c0..d60a676 100644 --- a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg +++ b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg @@ -39,7 +39,7 @@ enable_pin: !PE9 rotation_distance: 40 microsteps: 16 full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper -endstop_pin: ^PB14 +endstop_pin: ^PA1 position_min: 0 ##-------------------------------------------------------------------- @@ -78,7 +78,7 @@ enable_pin: !PD9 rotation_distance: 40 microsteps: 16 full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper -endstop_pin: ^PB13 +endstop_pin: ^PA2 position_min: 0 ##-------------------------------------------------------------------- From 25831638b01892f25b5c92b28e6cafe75a8ff059 Mon Sep 17 00:00:00 2001 From: shiftingtech <53156353+shiftingtech@users.noreply.github.com> Date: Sun, 15 Aug 2021 18:03:18 -0600 Subject: [PATCH 4/7] Update Voron2_Spider_Config.cfg Fixed fan max power --- firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg index d60a676..acc842f 100644 --- a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg +++ b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg @@ -317,7 +317,7 @@ heater_temp: 50.0 [fan] ## Print Cooling Fan - FAN1 Connector pin: PB1 -max_power: 0.4 +#max_power: 1.0 #kick_start_time: 0.5 ## Depending on your fan, you may need to increase this value ## if your fan will not start. Can change cycle_time (increase) From 3f449bf14d90999be003d72afe2621292648446c Mon Sep 17 00:00:00 2001 From: shiftingtech <53156353+shiftingtech@users.noreply.github.com> Date: Sun, 15 Aug 2021 18:08:12 -0600 Subject: [PATCH 5/7] Update Voron2_Spider_Config.cfg Removed rogue pixel count --- firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg | 1 - 1 file changed, 1 deletion(-) diff --git a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg index acc842f..e51d374 100644 --- a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg +++ b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg @@ -442,7 +442,6 @@ spi_software_sclk_pin: PA5 # To control Neopixel RGB in mini12864 display pin: PC12 chain_count: 3 -chain_count: 60 initial_RED: 0.1 initial_GREEN: 0.5 initial_BLUE: 0.0 From d5ca5901f901f5c0710619a8d725a599d8e5011b Mon Sep 17 00:00:00 2001 From: shiftingtech <53156353+shiftingtech@users.noreply.github.com> Date: Thu, 2 Sep 2021 22:17:26 -0600 Subject: [PATCH 6/7] Update Voron2_Spider_Config.cfg a few small cleanups to Spider printer.cfg --- .../Spider/Voron2_Spider_Config.cfg | 17 ++++++++--------- 1 file changed, 8 insertions(+), 9 deletions(-) diff --git a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg index e51d374..abab415 100644 --- a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg +++ b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg @@ -34,7 +34,7 @@ square_corner_velocity: 5.0 [stepper_x] ## Connected to X-MOT (B Motor) step_pin: PE11 -dir_pin: !PE10 +dir_pin: PE10 enable_pin: !PE9 rotation_distance: 40 microsteps: 16 @@ -73,7 +73,7 @@ stealthchop_threshold: 0 [stepper_y] ## Connected to Y-MOT (A Motor) step_pin: PD8 -dir_pin: !PB12 +dir_pin: PB12 enable_pin: !PD9 rotation_distance: 40 microsteps: 16 @@ -116,7 +116,7 @@ stealthchop_threshold: 0 ## Z0 Stepper - Front Left [stepper_z] step_pin: PD14 -dir_pin: !PD13 +dir_pin: PD13 enable_pin: !PD15 rotation_distance: 40 gear_ratio: 80:16 @@ -148,7 +148,6 @@ homing_retract_dist: 3 ## Make sure to update below for your relevant driver (2208 or 2209) [tmc2209 stepper_z] uart_pin: PD10 -uart_address: 0 interpolate: True run_current: 0.8 hold_current: 0.8 @@ -159,7 +158,7 @@ stealthchop_threshold: 0 ## Z1 Stepper - Rear Left [stepper_z1] step_pin: PE6 -dir_pin: PC13 +dir_pin: !PC13 enable_pin: !PE5 rotation_distance: 40 gear_ratio: 80:16 @@ -178,7 +177,7 @@ stealthchop_threshold: 0 ## Z2 Stepper - Rear Right [stepper_z2] step_pin: PE2 -dir_pin: !PE4 +dir_pin: PE4 enable_pin: !PE3 rotation_distance: 40 gear_ratio: 80:16 @@ -197,7 +196,7 @@ stealthchop_threshold: 0 ## Z3 Stepper - Front Right [stepper_z3] step_pin: PD12 -dir_pin: PC4 +dir_pin: !PC4 enable_pin: !PE8 rotation_distance: 40 gear_ratio: 80:16 @@ -218,7 +217,7 @@ stealthchop_threshold: 0 ## In E0-MOT Position [extruder] step_pin: PD5 -dir_pin: !PD6 +dir_pin: PD6 enable_pin: !PD4 ## Update value below when you perform extruder calibration @@ -502,7 +501,7 @@ gcode: G0 X125 Y250 F3600 ; park nozzle at rear BED_MESH_CLEAR -## Thermistor Types +## Common Temperature Sensors ## "EPCOS 100K B57560G104F" ## "ATC Semitec 104GT-2" ## "NTC 100K beta 3950" From a4a69bc1151c546aff32a010f60cae82feb99eab Mon Sep 17 00:00:00 2001 From: shiftingtech <53156353+shiftingtech@users.noreply.github.com> Date: Thu, 2 Sep 2021 22:40:06 -0600 Subject: [PATCH 7/7] Update Voron2_Spider_Config.cfg fixed probe definition --- .../klipper_configurations/Spider/Voron2_Spider_Config.cfg | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg index abab415..9fadb1c 100644 --- a/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg +++ b/firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg @@ -287,8 +287,8 @@ pid_kd: 363.769 [probe] ## This probe is not used for Z height, only Quad Gantry Leveling ## In Z+ position -## If your probe is NO instead of NC, add change pin to ^PA3 -pin: ^!PA3 +## If your probe is NO instead of NC, change pin to ^!PA3 +pin: ^PA3 x_offset: 0 y_offset: 25.0 z_offset: 0