diff --git a/Mods/README.md b/Mods/README.md index 8d4fa42..fb19ed3 100644 --- a/Mods/README.md +++ b/Mods/README.md @@ -302,6 +302,12 @@ Also covers the Z-belt hole for improved aesthetics. - Mount for an ethernet coupler to extend / move the ethernet plug somewhere more convenient. +## warriorofwire + +[Openbuilds Drag Chain](https://github.com/VoronDesign/Voron-2/tree/master/Mods/warriorofwire/openbuilds_drag_chain) + +- Collection of models for using an off-the-shelf, cheap, snap opening drag chain for gantry wiring and protecting wires down to the deck. + ## wile.e.coyote [Coroplast Support](https://github.com/VoronDesign/Voron-2/tree/master/Mods/wile.e.coyote) diff --git a/Mods/warriorofwire/openbuilds_drag_chain/README.md b/Mods/warriorofwire/openbuilds_drag_chain/README.md new file mode 100644 index 0000000..cca323e --- /dev/null +++ b/Mods/warriorofwire/openbuilds_drag_chain/README.md @@ -0,0 +1,29 @@ +# Off The Shelf Drag Chains for 2.1 +Note: Tested with 300mm 2.1 build only. + +## Why +* Drag chains with a snap open side are a joy to work on. +* It looks awesome. +* Looming up wires makes them harder to access. +* I hate tape chains. + +## BOM +* Some M3 screws +* A few M5 screws that are a couple millimeters longer than the M5's on the gantry. You'll figure it out. +* [3x Openbuilds 10x15mm 18mm radius Drag Chains](https://openbuildspartstore.com/drag-chain-cable-carrier/) +* All these stls + +## STLs +File | Note +---- | ---- +x_carriage_frame_right_remodeled | Parametrically driven remodel of the right toolhead without the wire tray. The through-screws are modeled like the original stl, but they seem pretty tight from my printer. YMMV, you might need a tap or just start working out more. +x_carriage_dragchain_anchorpoint | You screw your drag chain's floppy end to this side. +x_carriage_wire_cover | Cosmetic wire wrangler interfacing the drag chain to the X carriage. Mounts with a short M3 screw. +xy_drag_chain_bridge | You screw your drag chain's floppy end to this side. Wires go through it and up into the Y chain. +a_corner_wire_guide | Covers your wires around the A corner. Keeps them from chafing against the rail and frame, while keeping them tidily away from the belt. Also, you screw your drag chain's floppy end to this side. +lower_drag_chain_mount | Mounts to the rear lower frame. You'll need to cut an L shaped slot into your bottom panel. Also a great spot to run your bed and heater wires down through. Move this on the rail until you get a little tension on your Z chain. That'll keep it tight and it will look awesome. + +## Known Issues +* I haven't accounted for the toolhead doors yet. +* X carriage screws are a little tight. Probably "won't fix." +* A corner guide could be a little wider in critical places without interfering mechanically with the printer. All my wires fit, but yours might not. diff --git a/Mods/warriorofwire/openbuilds_drag_chain/a_corner_wire_guide.stl b/Mods/warriorofwire/openbuilds_drag_chain/a_corner_wire_guide.stl new file mode 100644 index 0000000..d40428d Binary files /dev/null and b/Mods/warriorofwire/openbuilds_drag_chain/a_corner_wire_guide.stl differ diff --git a/Mods/warriorofwire/openbuilds_drag_chain/lower_drag_chain_mount.stl b/Mods/warriorofwire/openbuilds_drag_chain/lower_drag_chain_mount.stl new file mode 100644 index 0000000..d2037c7 Binary files /dev/null and b/Mods/warriorofwire/openbuilds_drag_chain/lower_drag_chain_mount.stl differ diff --git a/Mods/warriorofwire/openbuilds_drag_chain/x_carriage_dragchain_anchorpoint.stl b/Mods/warriorofwire/openbuilds_drag_chain/x_carriage_dragchain_anchorpoint.stl new file mode 100644 index 0000000..9d93f09 Binary files /dev/null and b/Mods/warriorofwire/openbuilds_drag_chain/x_carriage_dragchain_anchorpoint.stl differ diff --git a/Mods/warriorofwire/openbuilds_drag_chain/x_carriage_frame_right_remodeled.stl b/Mods/warriorofwire/openbuilds_drag_chain/x_carriage_frame_right_remodeled.stl new file mode 100644 index 0000000..4a4263e Binary files /dev/null and b/Mods/warriorofwire/openbuilds_drag_chain/x_carriage_frame_right_remodeled.stl differ diff --git a/Mods/warriorofwire/openbuilds_drag_chain/x_carriage_wire_cover.stl b/Mods/warriorofwire/openbuilds_drag_chain/x_carriage_wire_cover.stl new file mode 100644 index 0000000..15a2bdf Binary files /dev/null and b/Mods/warriorofwire/openbuilds_drag_chain/x_carriage_wire_cover.stl differ diff --git a/Mods/warriorofwire/openbuilds_drag_chain/xy_drag_chain_bridge.stl b/Mods/warriorofwire/openbuilds_drag_chain/xy_drag_chain_bridge.stl new file mode 100644 index 0000000..a92d0a8 Binary files /dev/null and b/Mods/warriorofwire/openbuilds_drag_chain/xy_drag_chain_bridge.stl differ