From c4e87f7715e39b4852c81e9f2cf0738c163a27f3 Mon Sep 17 00:00:00 2001
From: Maglin <jeremiah.rempel@cox.net>
Date: Sun, 18 Nov 2018 12:31:19 -0600
Subject: [PATCH] Updating Config CAO 16NOV18

Just a few tuning changes
---
 .../Maglin Klipper Config/printer.cfg         | 63 ++++++++++++++-----
 1 file changed, 47 insertions(+), 16 deletions(-)

diff --git a/Firmware/Klipper/Voron_2.1/Klipper/Configurations/Maglin Klipper Config/printer.cfg b/Firmware/Klipper/Voron_2.1/Klipper/Configurations/Maglin Klipper Config/printer.cfg
index be705ee..b6db492 100644
--- a/Firmware/Klipper/Voron_2.1/Klipper/Configurations/Maglin Klipper Config/printer.cfg	
+++ b/Firmware/Klipper/Voron_2.1/Klipper/Configurations/Maglin Klipper Config/printer.cfg	
@@ -54,7 +54,7 @@ step_distance: 0.00250
 endstop_pin: ^!z:ar2
 # position endstop is to set your Z offset
 position_endstop: 1.95
-position_max: 250
+position_max: 255
 position_min: -25
 homing_speed: 12
 homing_positive_dir: false
@@ -93,13 +93,11 @@ speed: 5
 [homing_override]
 gcode:
     G90
-    G0 Z15 F2000
-	G28 X Y
+    G28 X Y
     G0 X250.2 Y234.5 F6000
     G28 Z
-    G0 Z5 F3000
+    G0 Z10 F3000
 axes: z
-set_position_z: 0
 
 #    macro to level the gantry.  use G32 in the terminal to call
 [gcode_macro g32]
@@ -212,28 +210,52 @@ gcode:
     G0 X254 Y0
     G0 X256 Y55
     G0 Z10
-
+    
+#    use probe_repeatability in your terminal to test 
+#    your inductive probe's repeatability
+[gcode_macro probe_repeatability]
+gcode:
+    G28
+    G32
+    G0 Z10 F9000
+    G0 X125 Y125 F9000
+    G4 P1000
+    probe
+    G0 Z10 F9000
+    G4 P1000
+    probe
+    G0 Z10 F9000
+    G4 P1000
+    probe
+    G0 Z10 F9000
+    G4 P1000
+    probe
+    G0 Z10 F9000
+    G4 P1000
+    probe
+    G0 Z10 F9000
+    
 [extruder]
 # on E0 stepper pins of main MCU
 step_pin: ar26
 dir_pin: ar28
 enable_pin: !ar24
 step_distance: 0.001761
-nozzle_diameter: 0.400
+nozzle_diameter: 0.50
 # PA can be disabled by declaring a 0.0 value
-pressure_advance: 0.05
+pressure_advance: 0.04
 # time seconds to look ahead for PA moves default is 0.010 or 10ms
-pressure_advance_lookahead_time: 0.020
+pressure_advance_lookahead_time: 0.010
 filament_diameter: 1.750
 max_extrude_only_distance: 800.0
 heater_pin: ar10
 sensor_type: ATC Semitec 104GT-2
 sensor_pin: analog13
-smooth_time: 2.0
-control: pid
-pid_Kp: 21.759
-pid_Ki: 1.107
-pid_Kd: 106.889
+smooth_time: 1.0
+#control: pid
+#pid_Kp: 21.759
+#pid_Ki: 1.107
+#pid_Kd: 106.889
 min_extrude_temp: 170
 min_temp: 0
 max_temp: 300
@@ -244,14 +266,14 @@ max_temp: 300
 # Due to large temp swing on print cooling fan I've changed this
 # to stop mid print heater faults.
 [verify_heater extruder]
-heating_gain: 1
+heating_gain: 2
 #   The minimum temperature (in Celsius) that the heater must increase
 #   by when approaching a new target temperature. The default is 2.
 check_gain_time: 40
 #   The amount of time (in seconds) that the heating_gain must be met
 #   in before an error is raised. The default is 20 seconds for
 #   extruders and 60 seconds for heater_bed.
-hysteresis: 5
+hysteresis: 10
 #   The difference between the target temperature and the current
 #   temperature for the heater to be considered within range of the
 #   target temperature. The default is 5.
@@ -354,3 +376,12 @@ gcode:
     G0 X125 Y245 F6000
     M84
 timeout: 1800
+
+#*# <---------------------- SAVE_CONFIG ---------------------->
+#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
+#*#
+#*# [extruder]
+#*# control = pid
+#*# pid_kp = 16.724
+#*# pid_ki = 0.587
+#*# pid_kd = 119.160