Created draft config for V2 Spider
This commit is contained in:
shiftingtech
parent
7dcd95e984
commit
83854dde57
GPG Key ID:
4AEE18F83AFDEB23
514
firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg
Normal file
514
firmware/klipper_configurations/Spider/Voron2_Spider_Config.cfg
Normal file
@ -0,0 +1,514 @@
|
|||||||
|
## Voron Design VORON2 250/300/350mm Spider TMC2209 UART config
|
||||||
|
|
||||||
|
## *** THINGS TO CHANGE/CHECK: ***
|
||||||
|
## MCU paths [mcu] section
|
||||||
|
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
||||||
|
## Z Endstop Switch location [safe_z_home] section
|
||||||
|
## Homing end position [gcode_macro G32] section
|
||||||
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
||||||
|
## Probe points [quad_gantry_level] section
|
||||||
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
||||||
|
## PID tune [extruder] and [heater_bed] sections
|
||||||
|
## Fine tune E steps [extruder] section
|
||||||
|
|
||||||
|
[mcu]
|
||||||
|
## Obtain definition by "ls -l /dev/serial/by-id/"
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_000000000000000000000000-if00
|
||||||
|
|
||||||
|
## Uncomment below if you're using the Raspberry uart0 to communicate with Spider
|
||||||
|
#restart_method: command
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: corexy
|
||||||
|
max_velocity: 300
|
||||||
|
max_accel: 3000 #Max 4000
|
||||||
|
max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V
|
||||||
|
max_z_accel: 350
|
||||||
|
square_corner_velocity: 5.0
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# X/Y Stepper Settings
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
[stepper_x]
|
||||||
|
## Connected to X-MOT (B Motor)
|
||||||
|
step_pin: PE11
|
||||||
|
dir_pin: !PE10
|
||||||
|
enable_pin: !PE9
|
||||||
|
rotation_distance: 40
|
||||||
|
microsteps: 16
|
||||||
|
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
||||||
|
endstop_pin: ^PB14
|
||||||
|
position_min: 0
|
||||||
|
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
|
||||||
|
## Uncomment below for 250mm build
|
||||||
|
#position_endstop: 250
|
||||||
|
#position_max: 250
|
||||||
|
|
||||||
|
## Uncomment for 300mm build
|
||||||
|
#position_endstop: 300
|
||||||
|
#position_max: 300
|
||||||
|
|
||||||
|
## Uncomment for 350mm build
|
||||||
|
#position_endstop: 350
|
||||||
|
#position_max: 350
|
||||||
|
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
homing_speed: 25 #Max 100
|
||||||
|
homing_retract_dist: 5
|
||||||
|
homing_positive_dir: true
|
||||||
|
|
||||||
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
|
[tmc2209 stepper_x]
|
||||||
|
uart_pin: PE7
|
||||||
|
interpolate: True
|
||||||
|
run_current: 0.8
|
||||||
|
hold_current: 0.7
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
[stepper_y]
|
||||||
|
## Connected to Y-MOT (A Motor)
|
||||||
|
step_pin: PD8
|
||||||
|
dir_pin: !PB12
|
||||||
|
enable_pin: !PD9
|
||||||
|
rotation_distance: 40
|
||||||
|
microsteps: 16
|
||||||
|
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
||||||
|
endstop_pin: ^PB13
|
||||||
|
position_min: 0
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
|
||||||
|
## Uncomment for 250mm build
|
||||||
|
#position_endstop: 250
|
||||||
|
#position_max: 250
|
||||||
|
|
||||||
|
## Uncomment for 300mm build
|
||||||
|
#position_endstop: 300
|
||||||
|
#position_max: 300
|
||||||
|
|
||||||
|
## Uncomment for 350mm build
|
||||||
|
#position_endstop: 350
|
||||||
|
#position_max: 350
|
||||||
|
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
homing_speed: 25 #Max 100
|
||||||
|
homing_retract_dist: 5
|
||||||
|
homing_positive_dir: true
|
||||||
|
|
||||||
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
|
[tmc2209 stepper_y]
|
||||||
|
uart_pin: PE15
|
||||||
|
interpolate: True
|
||||||
|
run_current: 0.8
|
||||||
|
hold_current: 0.7
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Z Stepper Settings
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
## In Z-MOT Position
|
||||||
|
## Z0 Stepper - Front Left
|
||||||
|
[stepper_z]
|
||||||
|
step_pin: PD14
|
||||||
|
dir_pin: !PD13
|
||||||
|
enable_pin: !PD15
|
||||||
|
rotation_distance: 40
|
||||||
|
gear_ratio: 80:16
|
||||||
|
microsteps: 16
|
||||||
|
## In Z- Position
|
||||||
|
endstop_pin: ^PA0
|
||||||
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||||
|
## (+) value = endstop above Z0, (-) value = endstop below
|
||||||
|
## Increasing position_endstop brings nozzle closer to the bed
|
||||||
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
||||||
|
position_endstop: -0.5
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
|
||||||
|
## Uncomment below for 250mm build
|
||||||
|
#position_max: 240
|
||||||
|
|
||||||
|
## Uncomment below for 300mm build
|
||||||
|
#position_max: 290
|
||||||
|
|
||||||
|
## Uncomment below for 350mm build
|
||||||
|
#position_max: 340
|
||||||
|
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
position_min: -5
|
||||||
|
homing_speed: 8
|
||||||
|
second_homing_speed: 3
|
||||||
|
homing_retract_dist: 3
|
||||||
|
|
||||||
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
|
[tmc2209 stepper_z]
|
||||||
|
uart_pin: PD10
|
||||||
|
uart_address: 0
|
||||||
|
interpolate: True
|
||||||
|
run_current: 0.8
|
||||||
|
hold_current: 0.8
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
## In E1-MOT Position
|
||||||
|
## Z1 Stepper - Rear Left
|
||||||
|
[stepper_z1]
|
||||||
|
step_pin: PE6
|
||||||
|
dir_pin: PC13
|
||||||
|
enable_pin: !PE5
|
||||||
|
rotation_distance: 40
|
||||||
|
gear_ratio: 80:16
|
||||||
|
microsteps: 16
|
||||||
|
|
||||||
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
|
[tmc2209 stepper_z1]
|
||||||
|
uart_pin: PC14
|
||||||
|
interpolate: True
|
||||||
|
run_current: 0.8
|
||||||
|
hold_current: 0.8
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
## In E2-MOT Position
|
||||||
|
## Z2 Stepper - Rear Right
|
||||||
|
[stepper_z2]
|
||||||
|
step_pin: PE2
|
||||||
|
dir_pin: !PE4
|
||||||
|
enable_pin: !PE3
|
||||||
|
rotation_distance: 40
|
||||||
|
gear_ratio: 80:16
|
||||||
|
microsteps: 16
|
||||||
|
|
||||||
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
|
[tmc2209 stepper_z2]
|
||||||
|
uart_pin: PC15
|
||||||
|
interpolate: true
|
||||||
|
run_current: 0.8
|
||||||
|
hold_current: 0.8
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
## In E3-MOT Position
|
||||||
|
## Z3 Stepper - Front Right
|
||||||
|
[stepper_z3]
|
||||||
|
step_pin: PD12
|
||||||
|
dir_pin: PC4
|
||||||
|
enable_pin: !PE8
|
||||||
|
rotation_distance: 40
|
||||||
|
gear_ratio: 80:16
|
||||||
|
microsteps: 16
|
||||||
|
|
||||||
|
[tmc2209 stepper_z3]
|
||||||
|
uart_pin: PA15
|
||||||
|
interpolate: true
|
||||||
|
run_current: 0.8
|
||||||
|
hold_current: 0.8
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Extruder
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
## In E0-MOT Position
|
||||||
|
[extruder]
|
||||||
|
step_pin: PD5
|
||||||
|
dir_pin: !PD6
|
||||||
|
enable_pin: !PD4
|
||||||
|
|
||||||
|
## Update value below when you perform extruder calibration
|
||||||
|
## If you ask for 100mm of filament, but in reality it is 98mm:
|
||||||
|
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
||||||
|
## 22.6789511 is a good starting point for Bondtech 5mm gears
|
||||||
|
## 34.37086 for Bondtech 8mm gears (Galileo)
|
||||||
|
rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears
|
||||||
|
## Update Gear Ratio depending on your Extruder Type
|
||||||
|
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
|
||||||
|
## Use 80:20 for M4, M3.1
|
||||||
|
## Use 7.5:1 for Galileo
|
||||||
|
gear_ratio: 50:17 #BMG Gear Ratio
|
||||||
|
microsteps: 16
|
||||||
|
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.75
|
||||||
|
## In E0 OUT Position
|
||||||
|
heater_pin: PB15
|
||||||
|
## Validate the following thermistor type to make sure it is correct
|
||||||
|
sensor_type: ATC Semitec 104GT-2
|
||||||
|
sensor_pin: PC0
|
||||||
|
min_temp: 10
|
||||||
|
max_temp: 270
|
||||||
|
max_power: 1.0
|
||||||
|
min_extrude_temp: 170
|
||||||
|
control = pid
|
||||||
|
pid_kp = 26.213
|
||||||
|
pid_ki = 1.304
|
||||||
|
pid_kd = 131.721
|
||||||
|
## Try to keep pressure_advance below 1.0
|
||||||
|
pressure_advance: 0.05
|
||||||
|
## Default is 0.040, leave stock
|
||||||
|
pressure_advance_smooth_time: 0.040
|
||||||
|
|
||||||
|
## In E0-MOT Position
|
||||||
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
|
[tmc2209 extruder]
|
||||||
|
uart_pin: PD7
|
||||||
|
interpolate: false
|
||||||
|
run_current: 0.5
|
||||||
|
hold_current: 0.4
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Bed Heater
|
||||||
|
#####################################################################
|
||||||
|
[heater_bed]
|
||||||
|
## SSR Pin - In BED OUT position
|
||||||
|
heater_pin: PB4
|
||||||
|
sensor_type: NTC 100K MGB18-104F39050L32
|
||||||
|
sensor_pin: PC3
|
||||||
|
## Adjust Max Power so your heater doesn't warp your bed
|
||||||
|
max_power: 0.6
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 120
|
||||||
|
control: pid
|
||||||
|
pid_kp: 58.437
|
||||||
|
pid_ki: 2.347
|
||||||
|
pid_kd: 363.769
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Probe
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
[probe]
|
||||||
|
## This probe is not used for Z height, only Quad Gantry Leveling
|
||||||
|
## In Z+ position
|
||||||
|
## If your probe is NO instead of NC, add change pin to ^PA3
|
||||||
|
pin: ^!PA3
|
||||||
|
x_offset: 0
|
||||||
|
y_offset: 25.0
|
||||||
|
z_offset: 0
|
||||||
|
speed: 10.0
|
||||||
|
samples: 3
|
||||||
|
samples_result: median
|
||||||
|
sample_retract_dist: 3.0
|
||||||
|
samples_tolerance: 0.006
|
||||||
|
samples_tolerance_retries: 3
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Fan Control
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
[heater_fan hotend_fan]
|
||||||
|
## Hotend Fan - FAN0 Connector
|
||||||
|
pin: PB0
|
||||||
|
max_power: 1.0
|
||||||
|
#kick_start_time: 0.5
|
||||||
|
heater: extruder
|
||||||
|
heater_temp: 50.0
|
||||||
|
## If you are experiencing back flow, you can reduce fan_speed
|
||||||
|
#fan_speed: 1.0
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
## Print Cooling Fan - FAN1 Connector
|
||||||
|
pin: PB1
|
||||||
|
max_power: 0.4
|
||||||
|
#kick_start_time: 0.5
|
||||||
|
## Depending on your fan, you may need to increase this value
|
||||||
|
## if your fan will not start. Can change cycle_time (increase)
|
||||||
|
## if your fan is not able to slow down effectively
|
||||||
|
off_below: 0.10
|
||||||
|
|
||||||
|
[heater_fan controller_fan]
|
||||||
|
## Controller fan - FAN2 Connector
|
||||||
|
pin: PB2
|
||||||
|
#kick_start_time: 0.5
|
||||||
|
heater: heater_bed
|
||||||
|
heater_temp: 45.0
|
||||||
|
|
||||||
|
#[heater_fan exhaust_fan]
|
||||||
|
## Exhaust fan - In E2 OUT Positon
|
||||||
|
#pin: PB3
|
||||||
|
#max_power: 1.0
|
||||||
|
#shutdown_speed: 0.0
|
||||||
|
##kick_start_time: 0.5
|
||||||
|
#heater: heater_bed
|
||||||
|
#heater_temp: 60
|
||||||
|
#fan_speed: 1.0
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# LED Control
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
#[output_pin caselight ]
|
||||||
|
## Chamber Lighting - In E1 OUT Position
|
||||||
|
#pin: PC8
|
||||||
|
#pwm: true
|
||||||
|
#shutdown_value: 0
|
||||||
|
#cycle_time: 0.01
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Homing and Gantry Adjustment Routines
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
[idle_timeout]
|
||||||
|
timeout: 1800
|
||||||
|
|
||||||
|
[safe_z_home]
|
||||||
|
## XY Location of the Z Endstop Switch
|
||||||
|
## Update -10,-10 to the XY coordinates of your endstop pin
|
||||||
|
## (such as 157,305) after going through Z Endstop Pin
|
||||||
|
## Location Definition step.
|
||||||
|
home_xy_position:-10,-10
|
||||||
|
speed:100
|
||||||
|
z_hop:10
|
||||||
|
|
||||||
|
[quad_gantry_level]
|
||||||
|
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||||
|
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
||||||
|
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
||||||
|
## to respective belt positions
|
||||||
|
|
||||||
|
#--------------------------------------------------------------------
|
||||||
|
## Gantry Corners for 250mm Build
|
||||||
|
## Uncomment for 250mm build
|
||||||
|
#gantry_corners:
|
||||||
|
# -60,-10
|
||||||
|
# 310, 320
|
||||||
|
## Probe points
|
||||||
|
#points:
|
||||||
|
# 50,25
|
||||||
|
# 50,175
|
||||||
|
# 200,175
|
||||||
|
# 200,25
|
||||||
|
|
||||||
|
## Gantry Corners for 300mm Build
|
||||||
|
## Uncomment for 300mm build
|
||||||
|
#gantry_corners:
|
||||||
|
# -60,-10
|
||||||
|
# 360,370
|
||||||
|
## Probe points
|
||||||
|
#points:
|
||||||
|
# 50,25
|
||||||
|
# 50,225
|
||||||
|
# 250,225
|
||||||
|
# 250,25
|
||||||
|
|
||||||
|
## Gantry Corners for 350mm Build
|
||||||
|
## Uncomment for 350mm build
|
||||||
|
#gantry_corners:
|
||||||
|
# -60,-10
|
||||||
|
# 410,420
|
||||||
|
## Probe points
|
||||||
|
#points:
|
||||||
|
# 50,25
|
||||||
|
# 50,275
|
||||||
|
# 300,275
|
||||||
|
# 300,25
|
||||||
|
|
||||||
|
#--------------------------------------------------------------------
|
||||||
|
speed: 100
|
||||||
|
horizontal_move_z: 10
|
||||||
|
retries: 5
|
||||||
|
retry_tolerance: 0.0075
|
||||||
|
max_adjust: 10
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Displays
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
#--------------------------------------------------------------------
|
||||||
|
|
||||||
|
[display]
|
||||||
|
# mini12864 LCD Display
|
||||||
|
lcd_type: uc1701
|
||||||
|
cs_pin: PC11
|
||||||
|
a0_pin: PD2
|
||||||
|
rst_pin: PC10
|
||||||
|
encoder_pins: ^PC6,^PC7
|
||||||
|
click_pin: ^!PA8
|
||||||
|
contrast: 63
|
||||||
|
#spi_bus: spi1
|
||||||
|
spi_software_mosi_pin: PA7
|
||||||
|
spi_software_miso_pin: PA6
|
||||||
|
spi_software_sclk_pin: PA5
|
||||||
|
|
||||||
|
[neopixel fysetc_mini12864]
|
||||||
|
# To control Neopixel RGB in mini12864 display
|
||||||
|
pin: PC12
|
||||||
|
chain_count: 3
|
||||||
|
chain_count: 60
|
||||||
|
initial_RED: 0.1
|
||||||
|
initial_GREEN: 0.5
|
||||||
|
initial_BLUE: 0.0
|
||||||
|
color_order: RGB
|
||||||
|
|
||||||
|
# Set RGB values on boot up for each Neopixel.
|
||||||
|
# Index 1 = display, Index 2 and 3 = Knob
|
||||||
|
[delayed_gcode setdisplayneopixel]
|
||||||
|
initial_duration: 1
|
||||||
|
gcode:
|
||||||
|
SET_LED LED=fysetc_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
|
||||||
|
SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
|
||||||
|
SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3
|
||||||
|
|
||||||
|
#--------------------------------------------------------------------
|
||||||
|
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Macros
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
[gcode_macro G32]
|
||||||
|
gcode:
|
||||||
|
BED_MESH_CLEAR
|
||||||
|
G28
|
||||||
|
QUAD_GANTRY_LEVEL
|
||||||
|
G28
|
||||||
|
## Uncomment for for your size printer:
|
||||||
|
#--------------------------------------------------------------------
|
||||||
|
## Uncomment for 250mm build
|
||||||
|
#G0 X125 Y125 Z30 F3600
|
||||||
|
|
||||||
|
## Uncomment for 300 build
|
||||||
|
#G0 X150 Y150 Z30 F3600
|
||||||
|
|
||||||
|
## Uncomment for 350mm build
|
||||||
|
#G0 X175 Y175 Z30 F3600
|
||||||
|
#--------------------------------------------------------------------
|
||||||
|
|
||||||
|
[gcode_macro PRINT_START]
|
||||||
|
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
||||||
|
gcode:
|
||||||
|
G32 ; home all axes
|
||||||
|
G1 Z20 F3000 ; move nozzle away from bed
|
||||||
|
|
||||||
|
[gcode_macro PRINT_END]
|
||||||
|
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
||||||
|
gcode:
|
||||||
|
M400 ; wait for buffer to clear
|
||||||
|
G92 E0 ; zero the extruder
|
||||||
|
G1 E-10.0 F3600 ; retract filament
|
||||||
|
G91 ; relative positioning
|
||||||
|
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
||||||
|
TURN_OFF_HEATERS
|
||||||
|
M107 ; turn off fan
|
||||||
|
G1 Z2 F3000 ; move nozzle up 2mm
|
||||||
|
G90 ; absolute positioning
|
||||||
|
G0 X125 Y250 F3600 ; park nozzle at rear
|
||||||
|
BED_MESH_CLEAR
|
||||||
|
|
||||||
|
## Thermistor Types
|
||||||
|
## "EPCOS 100K B57560G104F"
|
||||||
|
## "ATC Semitec 104GT-2"
|
||||||
|
## "NTC 100K beta 3950"
|
||||||
|
## "Honeywell 100K 135-104LAG-J01"
|
||||||
|
## "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
|
||||||
|
## "AD595"
|
||||||
|
## "PT100 INA826"
|
||||||
|
## "PT1000"
|
||||||
Loading…
Reference in New Issue
Block a user