volcom8190
commit
707406b613
GPG Key ID:
4AEE18F83AFDEB23
49
Mods/Chron/README.md
Normal file
49
Mods/Chron/README.md
Normal file
@ -0,0 +1,49 @@
|
||||
|
||||
## SKR 1.3 Pins
|
||||
```
|
||||
X_STEP_PIN 2.2
|
||||
X_DIR_PIN 2.6
|
||||
X_ENABLE_PIN 2.1
|
||||
X_MIN_PIN 1.29
|
||||
X_MAX_PIN 1.28
|
||||
X_UART_RX 1.17
|
||||
X_UART_TX 4.29
|
||||
|
||||
Y_STEP_PIN 0.19
|
||||
Y_DIR_PIN 0.20
|
||||
Y_ENABLE_PIN 2.8
|
||||
Y_MIN_PIN 1.27
|
||||
Y_MAX_PIN 1.26
|
||||
Y_UART_RX 1.15
|
||||
Y_UART_TX 1.16
|
||||
|
||||
Z_STEP_PIN 0.22
|
||||
Z_DIR_PIN 2.11
|
||||
Z_ENABLE_PIN 0.21
|
||||
Z_MIN_PIN 1.25
|
||||
Z_MAX_PIN 1.24
|
||||
Z_UART_RX 1.10
|
||||
Z_UART_TX 1.14
|
||||
|
||||
E0_STEP_PIN 2.13
|
||||
E0_DIR_PIN 0.11
|
||||
E0_ENABLE_PIN 2.12
|
||||
E0_UART_RX 1.8
|
||||
E0_UART_TX 1.9
|
||||
|
||||
E1_STEP_PIN 0.1
|
||||
E1_DIR_PIN 0.0
|
||||
E1_ENABLE_PIN 0.10
|
||||
E1_UART_RX 1.1
|
||||
E1_UART_TX 1.4
|
||||
|
||||
HE1 2.4
|
||||
HE0 2.7
|
||||
BED 2.5
|
||||
TH1 (H1 Temp) 0.25
|
||||
TH0 (H0 Temp) 0.24
|
||||
TB (Bed Temp) 0.23
|
||||
FAN 2.3
|
||||
SERVO 2.0
|
||||
```
|
||||
|
||||
504
Mods/Chron/SKR 1.3 Config/printer.cfg
Normal file
504
Mods/Chron/SKR 1.3 Config/printer.cfg
Normal file
@ -0,0 +1,504 @@
|
||||
# CHRONS VORON2 300mm SKR 1.3 TMC2208 UART config
|
||||
|
||||
# *** THINGS TO CHANGE/CHECK: ***
|
||||
# Arduino paths [mcu] section
|
||||
# Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
||||
# FSR switch (z endstop) location [homing_override] section
|
||||
# FSR switch (z endstop) offset for Z0 [stepper_z] section
|
||||
# Probe points [quad_gantry_level] section
|
||||
# Min & Max gantry corner postions [quad_gantry_level] section
|
||||
# PID tune [extruder] and [heater_bed] sections
|
||||
# Fine tune E steps [extruder] section
|
||||
|
||||
# ========================== Pin Definitions ==========================
|
||||
# X_STEP_PIN 2.2
|
||||
# X_DIR_PIN 2.6
|
||||
# X_ENABLE_PIN 2.1
|
||||
# X_MIN_PIN 1.29
|
||||
# X_MAX_PIN 1.28
|
||||
# X_UART_RX 1.17
|
||||
# X_UART_TX 4.29
|
||||
|
||||
# Y_STEP_PIN 0.19
|
||||
# Y_DIR_PIN 0.20
|
||||
# Y_ENABLE_PIN 2.8
|
||||
# Y_MIN_PIN 1.27
|
||||
# Y_MAX_PIN 1.26
|
||||
# Y_UART_RX 1.15
|
||||
# Y_UART_TX 1.16
|
||||
|
||||
# Z_STEP_PIN 0.22
|
||||
# Z_DIR_PIN 2.11
|
||||
# Z_ENABLE_PIN 0.21
|
||||
# Z_MIN_PIN 1.25
|
||||
# Z_MAX_PIN 1.24
|
||||
# Z_UART_RX 1.10
|
||||
# Z_UART_TX 1.14
|
||||
|
||||
# E0_STEP_PIN 2.13
|
||||
# E0_DIR_PIN 0.11
|
||||
# E0_ENABLE_PIN 2.12
|
||||
# E0_UART_RX 1.8
|
||||
# E0_UART_TX 1.9
|
||||
|
||||
# E1_STEP_PIN 0.1
|
||||
# E1_DIR_PIN 0.0
|
||||
# E1_ENABLE_PIN 0.10
|
||||
# E1_UART_RX 1.1
|
||||
# E1_UART_TX 1.4
|
||||
|
||||
# HE1 2.4
|
||||
# HE0 2.7
|
||||
# BED 2.5
|
||||
# TH1 (H1 Temp) 0.25
|
||||
# TH0 (H0 Temp) 0.24
|
||||
# TB (Bed Temp) 0.23
|
||||
# FAN 2.3
|
||||
# SERVO 2.0
|
||||
# =====================================================================
|
||||
|
||||
|
||||
[force_move]
|
||||
enable_force_move: True
|
||||
|
||||
[mcu]
|
||||
# mcu for X/Y/E steppers main MCU
|
||||
# [X in X] - B Motor
|
||||
# [Y in Y] - A Motor
|
||||
# [E in Z] - Extruder
|
||||
# obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify
|
||||
serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.2:1.0
|
||||
|
||||
[mcu z]
|
||||
# mcu for Z steppers
|
||||
# [Z in X] - Front Left
|
||||
# [Z1 in Y] - Rear Left
|
||||
# [Z2 in Z] - Rear Right
|
||||
# [Z3 in E0]- Front Right
|
||||
# obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify
|
||||
serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.3:1.0
|
||||
|
||||
[printer]
|
||||
kinematics: corexy
|
||||
max_velocity: 350
|
||||
max_accel: 4000
|
||||
max_z_velocity: 50
|
||||
max_z_accel: 350
|
||||
# The maximum velocity (in mm/s) that the toolhead may travel a 90
|
||||
# degree corner at. A non-zero value can reduce changes in extruder
|
||||
# flow rates by enabling instantaneous velocity changes of the
|
||||
# toolhead during cornering. This value configures the internal
|
||||
# centripetal velocity cornering algorithm; corners with angles
|
||||
# larger than 90 degrees will have a higher cornering velocity while
|
||||
# corners with angles less than 90 degrees will have a lower
|
||||
# cornering velocity. If this is set to zero then the toolhead will
|
||||
# decelerate to zero at each corner. The default is 5mm/s.
|
||||
#square_corner_velocity: 10.0
|
||||
|
||||
|
||||
#
|
||||
# TMC2208 UART Section for x/y
|
||||
#
|
||||
|
||||
[stepper_x]
|
||||
#connected to X on mcu_xye (B Motor)
|
||||
step_pin: P2.2
|
||||
dir_pin: !P2.6
|
||||
enable_pin: !P2.1
|
||||
step_distance: 0.0125
|
||||
endstop_pin: P1.29
|
||||
position_min: 0
|
||||
position_endstop: 305
|
||||
position_max: 305
|
||||
homing_speed: 50
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
[tmc2208 stepper_x]
|
||||
uart_pin: P1.17
|
||||
microsteps: 16
|
||||
interpolate: True
|
||||
run_current: 0.8
|
||||
hold_current: 0.5
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 250
|
||||
|
||||
[stepper_y]
|
||||
#connected to Y on mcu_xye (A Motor)
|
||||
step_pin: P0.19
|
||||
dir_pin: !P0.20
|
||||
enable_pin: !P2.8
|
||||
step_distance: 0.0125
|
||||
endstop_pin: P1.27
|
||||
position_min: 0
|
||||
position_endstop: 305
|
||||
position_max: 305
|
||||
homing_speed: 50
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
[tmc2208 stepper_y]
|
||||
uart_pin: P1.15
|
||||
microsteps: 16
|
||||
interpolate: True
|
||||
run_current: 0.8
|
||||
hold_current: 0.5
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 250
|
||||
|
||||
#
|
||||
# TMC2208 UART Section for z
|
||||
#
|
||||
|
||||
#Z MCU - IN X
|
||||
# Z0 Stepper - Front Left
|
||||
[stepper_z]
|
||||
step_pin: z:P2.2
|
||||
dir_pin: !z:P2.6
|
||||
enable_pin: !z:P2.1
|
||||
step_distance: 0.00250
|
||||
endstop_pin: !z:P1.25
|
||||
# Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||
# (+) value = endstop above Z0, (-) value = endstop below
|
||||
position_endstop: -0.5
|
||||
position_max: 240
|
||||
position_min: -5
|
||||
homing_speed: 15.0
|
||||
second_homing_speed: 3.0
|
||||
homing_retract_dist: 3.0
|
||||
|
||||
[tmc2208 stepper_z]
|
||||
uart_pin: z:P1.17
|
||||
microsteps: 16
|
||||
interpolate: True
|
||||
run_current: 0.90
|
||||
hold_current: 0.80
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 50
|
||||
|
||||
#Z MCU - IN Y
|
||||
# Z1 Stepper - Rear Left
|
||||
[stepper_z1]
|
||||
step_pin: z:P0.19
|
||||
dir_pin: z:P0.20
|
||||
enable_pin: !z:P2.8
|
||||
step_distance: 0.00250
|
||||
|
||||
|
||||
[tmc2208 stepper_z1]
|
||||
uart_pin: z:P1.15
|
||||
microsteps: 16
|
||||
interpolate: True
|
||||
run_current: 0.80
|
||||
hold_current: 0.80
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 50
|
||||
|
||||
#Z MCU - IN Z
|
||||
# Z2 Stepper - Rear Right
|
||||
[stepper_z2]
|
||||
step_pin: z:P0.22
|
||||
dir_pin: !z:P2.11
|
||||
enable_pin: !z:P0.21
|
||||
step_distance: 0.00250
|
||||
|
||||
[tmc2208 stepper_z2]
|
||||
uart_pin: z:P1.10
|
||||
microsteps: 16
|
||||
interpolate: True
|
||||
run_current: 0.90
|
||||
hold_current: 0.80
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 50
|
||||
|
||||
#Z MCU - IN E0
|
||||
# Z3 Stepper - Front Right
|
||||
[stepper_z3]
|
||||
step_pin: z:P2.13
|
||||
dir_pin: z:P0.11
|
||||
enable_pin: !z:P2.12
|
||||
step_distance: 0.00250
|
||||
|
||||
[tmc2208 stepper_z3]
|
||||
uart_pin: z:P1.8
|
||||
microsteps: 16
|
||||
interpolate: True
|
||||
run_current: 0.90
|
||||
hold_current: 0.80
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 50
|
||||
|
||||
#
|
||||
# bed heater, extruder and nozzle heater
|
||||
#
|
||||
|
||||
#Z on MCU X/Y
|
||||
[extruder]
|
||||
step_pin: P2.13
|
||||
dir_pin: P0.11
|
||||
enable_pin: !P2.12
|
||||
# 16 microsteps -m3 0.001875
|
||||
step_distance: 0.00180180
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.75
|
||||
heater_pin: P2.5
|
||||
sensor_type: NTC 100K beta 3950
|
||||
sensor_pin: P0.24
|
||||
smooth_time: 3.0
|
||||
min_temp: 10
|
||||
max_temp: 270
|
||||
max_power: 0.75
|
||||
min_extrude_temp: 170
|
||||
max_extrude_only_distance: 1150
|
||||
max_extrude_cross_section: 9999
|
||||
# PA can be disabled by declaring a 0.0 value
|
||||
pressure_advance: 0.0
|
||||
# time seconds to look ahead for PA moves default is 0.010 or 10ms
|
||||
pressure_advance_lookahead_time: 0.010
|
||||
control = pid
|
||||
pid_kp = 26.213
|
||||
pid_ki = 1.304
|
||||
pid_kd = 131.721
|
||||
|
||||
#Z on MCU X/Y
|
||||
[tmc2208 extruder]
|
||||
uart_pin: P1.10
|
||||
microsteps: 16
|
||||
interpolate: True
|
||||
run_current: 1.0
|
||||
hold_current: 1.0
|
||||
sense_resistor: 0.110
|
||||
stealthchop_threshold: 5
|
||||
|
||||
|
||||
[probe]
|
||||
# Inductive Probe
|
||||
# Z height probe. One may define this section to enable Z height
|
||||
# probing hardware. When this section is enabled, PROBE and
|
||||
# QUERY_PROBE extended g-code commands become available. The probe
|
||||
# section also creates a virtual "probe:z_virtual_endstop" pin. One
|
||||
# may set the stepper_z endstop_pin to this virtual pin on cartesian
|
||||
# style printers that use the probe in place of a z endstop.
|
||||
pin: !z:P1.24
|
||||
# Z_MAX on mcu_z
|
||||
x_offset: 0
|
||||
# Offset (in mm) for inductive probe Y direction from nozzle
|
||||
y_offset: 25.0
|
||||
z_offset: 0
|
||||
# Speed (in mm/s) of the Z axis when probing. The default is 5mm/s.
|
||||
speed: 2.0
|
||||
samples: 4
|
||||
# How far to retract (in mm) from the probe point for multi-probe samples
|
||||
sample_retract_dist: 3.0
|
||||
samples_tolerance: 0.100
|
||||
# The maximum Z distance (in mm) that a sample may differ from other
|
||||
# samples. If this tolerance is exceeded then either an error is
|
||||
# reported or the attempt is restarted (see
|
||||
# samples_tolerance_retries). The default is 0.100mm.
|
||||
samples_tolerance_retries: 3
|
||||
# The number of times to retry if a sample is found that exceeds
|
||||
# samples_tolerance. On a retry, all current samples are discarded
|
||||
# and the probe attempt is restarted. If a valid set of samples are
|
||||
# not obtained in the given number of retries then an error is
|
||||
# reported. The default is zero which causes an error to be reported
|
||||
# on the first sample that exceeds samples_tolerance
|
||||
|
||||
|
||||
#
|
||||
# Fan control
|
||||
#
|
||||
|
||||
[fan]
|
||||
# print cooling fans
|
||||
pin: P2.4
|
||||
#max_power: 0.5
|
||||
kick_start_time: 0.5
|
||||
cycle_time: 0.001
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
# Hotend fan MCU Z
|
||||
pin: P2.7
|
||||
#max_power: 0.8
|
||||
#shutdown_speed: 0.0
|
||||
kick_start_time: 0.5
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
#fan_speed: 1.0
|
||||
|
||||
#[heater_fan controller_fan]
|
||||
# Controller fan
|
||||
#pin: z:ar10
|
||||
# D10 on mcu_z
|
||||
#kick_start_time: 0.500
|
||||
#heater: heater_bed
|
||||
#heater_temp: 45.0
|
||||
|
||||
[heater_fan exhaust_fan]
|
||||
pin: z:P2.4
|
||||
#max_power: 1.0
|
||||
#shutdown_speed: 0.0
|
||||
kick_start_time: 5.0
|
||||
heater: heater_bed
|
||||
heater_temp: 60
|
||||
#fan_speed: 1.0
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: z:P2.5
|
||||
sensor_type: NTC 100K MGB18-104F39050L32
|
||||
#pullup_resistor: 5500
|
||||
sensor_pin: z:P0.25
|
||||
smooth_time: 3.0
|
||||
max_power: 1.0
|
||||
min_temp: 0
|
||||
max_temp: 110
|
||||
control: pid
|
||||
pid_kp: 58.437
|
||||
pid_ki: 2.347
|
||||
pid_kd: 363.769
|
||||
|
||||
[idle_timeout]
|
||||
timeout: 1800
|
||||
|
||||
[verify_heater heater_bed]
|
||||
hysteresis: 0.5
|
||||
check_gain_time: 120
|
||||
|
||||
[homing_override]
|
||||
axes: z
|
||||
set_position_z: 0
|
||||
gcode:
|
||||
G90
|
||||
G0 Z5 F600
|
||||
G28 X Y
|
||||
# XY Location of the FSR Switch
|
||||
G0 X99.7 Y305 F3600
|
||||
G28 Z
|
||||
G0 Z10 F1800
|
||||
G0 X150 Y150 Z30 F3600
|
||||
|
||||
|
||||
[quad_gantry_level]
|
||||
# Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||
# Min & Max gantry corners - measure from nozzle at MIN (0,0) and MAX (300,300) to respective belt positions
|
||||
gantry_corners:
|
||||
-55,-7
|
||||
355,370
|
||||
# Probe points
|
||||
points:
|
||||
60,60
|
||||
60,240
|
||||
240,240
|
||||
240,60
|
||||
# The speed (in mm/s) of non-probing moves during the calibration.
|
||||
# The default is 50.
|
||||
speed: 50
|
||||
# The height (in mm) that the head should be commanded to move to
|
||||
# just prior to starting a probe operation. The default is 5
|
||||
horizontal_move_z: 10
|
||||
# number of times to retry if the stepper movements aren't within tolerance
|
||||
retries: 5
|
||||
# if retries are enabled then retry if any z_stepper movement was greater
|
||||
# than the retry_tolerance
|
||||
retry_tolerance: 0.0075
|
||||
# Saftey limit if an ajustment greater than this value is requested
|
||||
# quad_gantry_level will abort.
|
||||
max_adjust: 10
|
||||
|
||||
|
||||
# BED_MESH_CALIBRATE
|
||||
[bed_mesh]
|
||||
speed: 200
|
||||
horizontal_move_z: 10
|
||||
min_point: 20,20
|
||||
max_point: 280,280
|
||||
probe_count: 10,10
|
||||
fade_start: 0.5
|
||||
fade_end: 25.0
|
||||
split_delta_z: .025
|
||||
move_check_distance: 5.0
|
||||
mesh_pps: 0,0
|
||||
algorithm: bicubic
|
||||
|
||||
|
||||
[display]
|
||||
# RepRapDiscount 128x64 Full Graphic Smart Controller
|
||||
lcd_type: st7920
|
||||
cs_pin: z:P1.19
|
||||
sclk_pin: z:P1.20
|
||||
sid_pin: z:P1.18
|
||||
# LCD connector on mcu_z
|
||||
menu_timeout: 40
|
||||
# Timeout for menu. Being inactive this amount of seconds will exit the menu
|
||||
# Default is 0 seconds (disabled)
|
||||
encoder_pins: ^z:P3.26, ^z:P3.25
|
||||
click_pin: ^!z:P0.28
|
||||
#kill_pin: ^!z:
|
||||
|
||||
|
||||
### Macros ###
|
||||
|
||||
[gcode_macro G32]
|
||||
gcode:
|
||||
G28
|
||||
QUAD_GANTRY_LEVEL
|
||||
G28
|
||||
G0 X150 Y150 Z20 F6000
|
||||
|
||||
[gcode_macro PRINT_START]
|
||||
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
||||
gcode:
|
||||
M117 Homing... ; display message
|
||||
G28 ; home all axes
|
||||
G1 Z20 F3000 ; move nozzle away from bed
|
||||
M117 Preheat (Print) ; display message
|
||||
M104 S0 ; turn off hotend while waiting for bed to get to temp)
|
||||
|
||||
[gcode_macro PRINT_END]
|
||||
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
||||
gcode:
|
||||
M400 ; wait for buffer to clear
|
||||
G92 E0 ; zero the extruder
|
||||
G1 E-10.0 F3600 ; retract filament
|
||||
G91 ; relative positioning
|
||||
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
||||
TURN_OFF_HEATERS
|
||||
M107 ; turn off fan
|
||||
G1 Z2 F3000 ; move nozzle up 2mm
|
||||
G90 ; absolute positioning
|
||||
G0 X125 Y250 F3600 ; park nozzle at rear
|
||||
M117 Finished!
|
||||
|
||||
[gcode_macro LOAD_FILAMENT]
|
||||
gcode:
|
||||
M83 ; set extruder to relative
|
||||
G1 E750 F1800 ; quickly load filament to down bowden
|
||||
G1 E30 F300 ; slower extrusion for hotend path
|
||||
G1 E15 F150 ; prime nozzle with filament
|
||||
M82 ; set extruder to absolute
|
||||
|
||||
[gcode_macro UNLOAD_FILAMENT]
|
||||
gcode:
|
||||
M83 ; set extruder to relative
|
||||
G1 E10 F300 ; extrude a little to soften tip
|
||||
G1 E-780 F1800 ; retract filament completely
|
||||
M82 ; set extruder to absolute
|
||||
|
||||
[gcode_macro quad_me]
|
||||
gcode:
|
||||
G28
|
||||
quad_gantry_level
|
||||
G28
|
||||
quad_gantry_level
|
||||
G28
|
||||
quad_gantry_level
|
||||
G28
|
||||
G1 X150 Y150 Z20
|
||||
|
||||
# Sensor Types
|
||||
# "EPCOS 100K B57560G104F"
|
||||
# "ATC Semitec 104GT-2"
|
||||
# "NTC 100K beta 3950"
|
||||
# "Honeywell 100K 135-104LAG-J01"
|
||||
# "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
|
||||
# "AD595"
|
||||
# "PT100 INA826"
|
||||
BIN
Mods/Chron/skr_1.3.png
Normal file
BIN
Mods/Chron/skr_1.3.png
Normal file
Binary file not shown.
|
After Width: | Height: | Size: 716 KiB |
Loading…
Reference in New Issue
Block a user