From 3780605aae455ca33a78db45379173542fa355c4 Mon Sep 17 00:00:00 2001 From: chron-kh <51377081+chron-kh@users.noreply.github.com> Date: Fri, 26 Jul 2019 13:48:19 -0400 Subject: [PATCH] Delete SKR 1.3 Config --- Mods/Chron/SKR 1.3 Config | 504 -------------------------------------- 1 file changed, 504 deletions(-) delete mode 100644 Mods/Chron/SKR 1.3 Config diff --git a/Mods/Chron/SKR 1.3 Config b/Mods/Chron/SKR 1.3 Config deleted file mode 100644 index f82aab3..0000000 --- a/Mods/Chron/SKR 1.3 Config +++ /dev/null @@ -1,504 +0,0 @@ -# CHRONS VORON2 300mm SKR 1.3 TMC2208 UART config - -# *** THINGS TO CHANGE/CHECK: *** -# Arduino paths [mcu] section -# Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file -# FSR switch (z endstop) location [homing_override] section -# FSR switch (z endstop) offset for Z0 [stepper_z] section -# Probe points [quad_gantry_level] section -# Min & Max gantry corner postions [quad_gantry_level] section -# PID tune [extruder] and [heater_bed] sections -# Fine tune E steps [extruder] section - -# ========================== Pin Definitions ========================== -# X_STEP_PIN 2.2 -# X_DIR_PIN 2.6 -# X_ENABLE_PIN 2.1 -# X_MIN_PIN 1.29 -# X_MAX_PIN 1.28 -# X_UART_RX 1.17 -# X_UART_TX 4.29 - -# Y_STEP_PIN 0.19 -# Y_DIR_PIN 0.20 -# Y_ENABLE_PIN 2.8 -# Y_MIN_PIN 1.27 -# Y_MAX_PIN 1.26 -# Y_UART_RX 1.15 -# Y_UART_TX 1.16 - -# Z_STEP_PIN 0.22 -# Z_DIR_PIN 2.11 -# Z_ENABLE_PIN 0.21 -# Z_MIN_PIN 1.25 -# Z_MAX_PIN 1.24 -# Z_UART_RX 1.10 -# Z_UART_TX 1.14 - -# E0_STEP_PIN 2.13 -# E0_DIR_PIN 0.11 -# E0_ENABLE_PIN 2.12 -# E0_UART_RX 1.8 -# E0_UART_TX 1.9 - -# E1_STEP_PIN 0.1 -# E1_DIR_PIN 0.0 -# E1_ENABLE_PIN 0.10 -# E1_UART_RX 1.1 -# E1_UART_TX 1.4 - -# HE1 2.4 -# HE0 2.7 -# BED 2.5 -# TH1 (H1 Temp) 0.25 -# TH0 (H0 Temp) 0.24 -# TB (Bed Temp) 0.23 -# FAN 2.3 -# SERVO 2.0 -# ===================================================================== - - -[force_move] -enable_force_move: True - -[mcu] -# mcu for X/Y/E steppers main MCU -# [X in X] - B Motor -# [Y in Y] - A Motor -# [E in Z] - Extruder -# obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify -serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.2:1.0 - -[mcu z] -# mcu for Z steppers -# [Z in X] - Front Left -# [Z1 in Y] - Rear Left -# [Z2 in Z] - Rear Right -# [Z3 in E0]- Front Right -# obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify -serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.3:1.0 - -[printer] -kinematics: corexy -max_velocity: 350 -max_accel: 4000 -max_z_velocity: 50 -max_z_accel: 350 -# The maximum velocity (in mm/s) that the toolhead may travel a 90 -# degree corner at. A non-zero value can reduce changes in extruder -# flow rates by enabling instantaneous velocity changes of the -# toolhead during cornering. This value configures the internal -# centripetal velocity cornering algorithm; corners with angles -# larger than 90 degrees will have a higher cornering velocity while -# corners with angles less than 90 degrees will have a lower -# cornering velocity. If this is set to zero then the toolhead will -# decelerate to zero at each corner. The default is 5mm/s. -#square_corner_velocity: 10.0 - - -# -# TMC2208 UART Section for x/y -# - -[stepper_x] -#connected to X on mcu_xye (B Motor) -step_pin: P2.2 -dir_pin: !P2.6 -enable_pin: !P2.1 -step_distance: 0.0125 -endstop_pin: P1.29 -position_min: 0 -position_endstop: 305 -position_max: 305 -homing_speed: 50 -homing_retract_dist: 5 -homing_positive_dir: true - -[tmc2208 stepper_x] -uart_pin: P1.17 -microsteps: 16 -interpolate: True -run_current: 0.8 -hold_current: 0.5 -sense_resistor: 0.110 -stealthchop_threshold: 250 - -[stepper_y] -#connected to Y on mcu_xye (A Motor) -step_pin: P0.19 -dir_pin: !P0.20 -enable_pin: !P2.8 -step_distance: 0.0125 -endstop_pin: P1.27 -position_min: 0 -position_endstop: 305 -position_max: 305 -homing_speed: 50 -homing_retract_dist: 5 -homing_positive_dir: true - -[tmc2208 stepper_y] -uart_pin: P1.15 -microsteps: 16 -interpolate: True -run_current: 0.8 -hold_current: 0.5 -sense_resistor: 0.110 -stealthchop_threshold: 250 - -# -# TMC2208 UART Section for z -# - -#Z MCU - IN X -# Z0 Stepper - Front Left -[stepper_z] -step_pin: z:P2.2 -dir_pin: !z:P2.6 -enable_pin: !z:P2.1 -step_distance: 0.00250 -endstop_pin: !z:P1.25 -# Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) -# (+) value = endstop above Z0, (-) value = endstop below -position_endstop: -0.5 -position_max: 240 -position_min: -5 -homing_speed: 15.0 -second_homing_speed: 3.0 -homing_retract_dist: 3.0 - -[tmc2208 stepper_z] -uart_pin: z:P1.17 -microsteps: 16 -interpolate: True -run_current: 0.90 -hold_current: 0.80 -sense_resistor: 0.110 -stealthchop_threshold: 50 - -#Z MCU - IN Y -# Z1 Stepper - Rear Left -[stepper_z1] -step_pin: z:P0.19 -dir_pin: z:P0.20 -enable_pin: !z:P2.8 -step_distance: 0.00250 - - -[tmc2208 stepper_z1] -uart_pin: z:P1.15 -microsteps: 16 -interpolate: True -run_current: 0.80 -hold_current: 0.80 -sense_resistor: 0.110 -stealthchop_threshold: 50 - -#Z MCU - IN Z -# Z2 Stepper - Rear Right -[stepper_z2] -step_pin: z:P0.22 -dir_pin: !z:P2.11 -enable_pin: !z:P0.21 -step_distance: 0.00250 - -[tmc2208 stepper_z2] -uart_pin: z:P1.10 -microsteps: 16 -interpolate: True -run_current: 0.90 -hold_current: 0.80 -sense_resistor: 0.110 -stealthchop_threshold: 50 - -#Z MCU - IN E0 -# Z3 Stepper - Front Right -[stepper_z3] -step_pin: z:P2.13 -dir_pin: z:P0.11 -enable_pin: !z:P2.12 -step_distance: 0.00250 - -[tmc2208 stepper_z3] -uart_pin: z:P1.8 -microsteps: 16 -interpolate: True -run_current: 0.90 -hold_current: 0.80 -sense_resistor: 0.110 -stealthchop_threshold: 50 - -# -# bed heater, extruder and nozzle heater -# - -#Z on MCU X/Y -[extruder] -step_pin: P2.13 -dir_pin: P0.11 -enable_pin: !P2.12 -# 16 microsteps -m3 0.001875 -step_distance: 0.00180180 -nozzle_diameter: 0.400 -filament_diameter: 1.75 -heater_pin: P2.5 -sensor_type: NTC 100K beta 3950 -sensor_pin: P0.24 -smooth_time: 3.0 -min_temp: 10 -max_temp: 270 -max_power: 0.75 -min_extrude_temp: 170 -max_extrude_only_distance: 1150 -max_extrude_cross_section: 9999 -# PA can be disabled by declaring a 0.0 value -pressure_advance: 0.0 -# time seconds to look ahead for PA moves default is 0.010 or 10ms -pressure_advance_lookahead_time: 0.010 -control = pid -pid_kp = 26.213 -pid_ki = 1.304 -pid_kd = 131.721 - -#Z on MCU X/Y -[tmc2208 extruder] -uart_pin: P1.10 -microsteps: 16 -interpolate: True -run_current: 1.0 -hold_current: 1.0 -sense_resistor: 0.110 -stealthchop_threshold: 5 - - -[probe] -# Inductive Probe -# Z height probe. One may define this section to enable Z height -# probing hardware. When this section is enabled, PROBE and -# QUERY_PROBE extended g-code commands become available. The probe -# section also creates a virtual "probe:z_virtual_endstop" pin. One -# may set the stepper_z endstop_pin to this virtual pin on cartesian -# style printers that use the probe in place of a z endstop. -pin: !z:P1.24 -# Z_MAX on mcu_z -x_offset: 0 -# Offset (in mm) for inductive probe Y direction from nozzle -y_offset: 25.0 -z_offset: 0 -# Speed (in mm/s) of the Z axis when probing. The default is 5mm/s. -speed: 2.0 -samples: 4 -# How far to retract (in mm) from the probe point for multi-probe samples -sample_retract_dist: 3.0 -samples_tolerance: 0.100 -# The maximum Z distance (in mm) that a sample may differ from other -# samples. If this tolerance is exceeded then either an error is -# reported or the attempt is restarted (see -# samples_tolerance_retries). The default is 0.100mm. -samples_tolerance_retries: 3 -# The number of times to retry if a sample is found that exceeds -# samples_tolerance. On a retry, all current samples are discarded -# and the probe attempt is restarted. If a valid set of samples are -# not obtained in the given number of retries then an error is -# reported. The default is zero which causes an error to be reported -# on the first sample that exceeds samples_tolerance - - -# -# Fan control -# - -[fan] -# print cooling fans -pin: P2.4 -#max_power: 0.5 -kick_start_time: 0.5 -cycle_time: 0.001 - -[heater_fan hotend_fan] -# Hotend fan MCU Z -pin: P2.7 -#max_power: 0.8 -#shutdown_speed: 0.0 -kick_start_time: 0.5 -heater: extruder -heater_temp: 50.0 -#fan_speed: 1.0 - -#[heater_fan controller_fan] -# Controller fan -#pin: z:ar10 -# D10 on mcu_z -#kick_start_time: 0.500 -#heater: heater_bed -#heater_temp: 45.0 - -[heater_fan exhaust_fan] -pin: z:P2.4 -#max_power: 1.0 -#shutdown_speed: 0.0 -kick_start_time: 5.0 -heater: heater_bed -heater_temp: 60 -#fan_speed: 1.0 - -[heater_bed] -heater_pin: z:P2.5 -sensor_type: NTC 100K MGB18-104F39050L32 -#pullup_resistor: 5500 -sensor_pin: z:P0.25 -smooth_time: 3.0 -max_power: 1.0 -min_temp: 0 -max_temp: 110 -control: pid -pid_kp: 58.437 -pid_ki: 2.347 -pid_kd: 363.769 - -[idle_timeout] -timeout: 1800 - -[verify_heater heater_bed] -hysteresis: 0.5 -check_gain_time: 120 - -[homing_override] -axes: z -set_position_z: 0 -gcode: - G90 - G0 Z5 F600 - G28 X Y - # XY Location of the FSR Switch - G0 X99.7 Y305 F3600 - G28 Z - G0 Z10 F1800 - G0 X150 Y150 Z30 F3600 - - -[quad_gantry_level] -# Use QUAD_GANTRY_LEVEL to level a gantry. -# Min & Max gantry corners - measure from nozzle at MIN (0,0) and MAX (300,300) to respective belt positions -gantry_corners: - -55,-7 - 355,370 -# Probe points -points: - 60,60 - 60,240 - 240,240 - 240,60 - # The speed (in mm/s) of non-probing moves during the calibration. -# The default is 50. -speed: 50 -# The height (in mm) that the head should be commanded to move to -# just prior to starting a probe operation. The default is 5 -horizontal_move_z: 10 -# number of times to retry if the stepper movements aren't within tolerance -retries: 5 -# if retries are enabled then retry if any z_stepper movement was greater -# than the retry_tolerance -retry_tolerance: 0.0075 -# Saftey limit if an ajustment greater than this value is requested -# quad_gantry_level will abort. -max_adjust: 10 - - -# BED_MESH_CALIBRATE -[bed_mesh] -speed: 200 -horizontal_move_z: 10 -min_point: 20,20 -max_point: 280,280 -probe_count: 10,10 -fade_start: 0.5 -fade_end: 25.0 -split_delta_z: .025 -move_check_distance: 5.0 -mesh_pps: 0,0 -algorithm: bicubic - - -[display] -# RepRapDiscount 128x64 Full Graphic Smart Controller -lcd_type: st7920 -cs_pin: z:P1.19 -sclk_pin: z:P1.20 -sid_pin: z:P1.18 -# LCD connector on mcu_z -menu_timeout: 40 -# Timeout for menu. Being inactive this amount of seconds will exit the menu -# Default is 0 seconds (disabled) -encoder_pins: ^z:P3.26, ^z:P3.25 -click_pin: ^!z:P0.28 -#kill_pin: ^!z: - - -### Macros ### - -[gcode_macro G32] -gcode: - G28 - QUAD_GANTRY_LEVEL - G28 - G0 X150 Y150 Z20 F6000 - -[gcode_macro PRINT_START] -# Use PRINT_START for the slicer starting script - please customise for your slicer of choice -gcode: - M117 Homing... ; display message - G28 ; home all axes - G1 Z20 F3000 ; move nozzle away from bed - M117 Preheat (Print) ; display message - M104 S0 ; turn off hotend while waiting for bed to get to temp) - -[gcode_macro PRINT_END] -# Use PRINT_END for the slicer ending script - please customise for your slicer of choice -gcode: - M400 ; wait for buffer to clear - G92 E0 ; zero the extruder - G1 E-10.0 F3600 ; retract filament - G91 ; relative positioning - G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing - TURN_OFF_HEATERS - M107 ; turn off fan - G1 Z2 F3000 ; move nozzle up 2mm - G90 ; absolute positioning - G0 X125 Y250 F3600 ; park nozzle at rear - M117 Finished! - -[gcode_macro LOAD_FILAMENT] -gcode: - M83 ; set extruder to relative - G1 E750 F1800 ; quickly load filament to down bowden - G1 E30 F300 ; slower extrusion for hotend path - G1 E15 F150 ; prime nozzle with filament - M82 ; set extruder to absolute - -[gcode_macro UNLOAD_FILAMENT] -gcode: - M83 ; set extruder to relative - G1 E10 F300 ; extrude a little to soften tip - G1 E-780 F1800 ; retract filament completely - M82 ; set extruder to absolute - -[gcode_macro quad_me] -gcode: - G28 - quad_gantry_level - G28 - quad_gantry_level - G28 - quad_gantry_level - G28 - G1 X150 Y150 Z20 - -# Sensor Types -# "EPCOS 100K B57560G104F" -# "ATC Semitec 104GT-2" -# "NTC 100K beta 3950" -# "Honeywell 100K 135-104LAG-J01" -# "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad) -# "AD595" -# "PT100 INA826"